Menu items in the 300s, relating to editing operations
Item number | Item name | Settings |
|
| ||||
344 | ASSEMBLE AUTO EDIT | Set whether to record 2 seconds of postroll when an additional clip is |
|
| ||||
| POSTROLL RECORDING | recorded by sending the AUTO EDIT command |
|
| ||||
|
|
| from a nonlinear editing system connected to the REMOTE(9P) |
|
| |||
|
|
| connector on the rear panel. |
|
| |||
|
|
|
|
|
|
|
| |
|
|
| Note |
|
|
|
| |
|
|
| When | using a linear editing system, postroll will not be recorded |
|
| ||
|
|
| regardless of this setting. |
|
| |||
|
|
| off: Do not record postroll. |
|
| |||
|
|
| on: Records approximately 2 seconds of postroll. |
|
| |||
|
|
|
|
|
|
|
| |
|
| Menu items in the 400s, relating to preroll |
|
| ||||
|
|
|
|
|
|
|
| |
Item number | Item name | Settings |
|
| ||||
401 | FUNCTION MODE AFTER | Select the state that the unit goes into after a |
|
| ||||
|
|
| stop: Stops (the stop mode). |
|
| |||
|
|
| still: Still playback (in jog and shuttle mode). |
|
| |||
|
|
|
|
|
|
|
| |
|
| Menu items in the 500s, relating to disc protection |
|
| ||||
|
|
|
|
|
|
|
| |
Item number | Item name | Settings |
|
| ||||
501 | STILL TIMER | To protect the disc against shock and vibrations, and to lengthen the life |
|
| ||||
|
|
| of the laser diodes, the unit automatically enters standby off mode |
|
| |||
|
|
| whenever a specified time elapses in a disc stop mode (stop mode or the |
|
| |||
|
|
| still picture mode of search mode). This allows you to set the time after |
|
| |||
|
|
| which the unit exits a disc stop mode and enters standby off mode. |
|
| |||
|
|
| 0.5 s (0.5 sec)... 8 m (8 min)... 30 m (30 min): Can be set in the range |
|
| |||
|
|
| from 0.5 seconds to 30 minutes. |
|
| |||
|
|
| off: Do not put into standby off mode. |
|
| |||
|
|
|
|
|
| |||
| Menu items in the 600s, relating to the timecode, metadata, and UMID |
|
| |||||
|
|
|
|
|
|
|
| |
Item number | Item name | Settings |
|
| ||||
601 | VITC POSITION | In 59.94i mode | Select the line into which to insert VITC signals (SD output) |
|
| |||
|
| 12H ... [16H] ... 20H: Any line from line 12 through line 20. |
|
| ||||
|
|
|
|
|
|
| ||
|
|
| Notes |
|
|
| ||
|
|
| • You can insert VITC signals in two places. To insert in two places, set |
|
| |||
|
|
| both item 601 and item 602. |
|
| |||
|
|
| • In 59.94i mode (J), output of wide picture information is given priority if |
|
| |||
|
|
| OUTPUT in setup menu item 731 is set to “auto” and the VITC insertion |
|
| |||
|
|
| line is set to line 16. |
|
| |||
|
|
| • In 59.94i mode (UC), output of wide picture information is given priority |
|
| |||
|
|
| if OUTPUT in setup menu item 731 is set to “auto” and the VITC |
|
| |||
|
|
| insertion line is set to line 20. |
|
| |||
|
|
|
|
|
| |||
|
| In 50i mode | Select the line into which to insert VITC signals (SD output) |
|
| |||
|
|
| 9H ... [19H] ... 22H: Any line from line 9 through line 22. |
|
| |||
|
|
|
|
|
| |||
|
|
| Note |
|
|
| ||
|
|
| You can insert VITC signals in two places. To insert in two places, set |
|
| |||
|
|
| both item 601 and item 602. |
|
| |||
|
|
|
|
|
|
|
|
|
Menus 7 Chapter
Setup Menu 99