iMAINTENANCE connectors

These are the USB connectors for maintenance.

Note

Do not connect USB devices to this unit for any purpose other than maintenance.

j SDSDI OUTPUT 1, 2 (SUPER) (SDI signal outputs 1, 2 (superimpose)) connectors (BNC type)

 

 

These output SDSDI format video/audio signals.

 

 

Chapter

 

When the unit is shipped from the factory, audio signal

 

output is eight channels with no switching, and RP188

 

 

2

 

timecode output is set to on. You can change these settings

 

with setup menu item 828 SDI AUDIO OUTPUT

Names

 

 

SELECT and setup menu item 920 SD-SDI H-ANC

 

 

and

 

CONTROL.

 

 

 

The output from the 2 (SUPER) connector can have

Functions

 

 

timecode, menu settings, alarm messages, and other text

 

 

 

 

information superimposed. To turn superimposition off,

of

 

set CHAR SEL on the HOME page of the function menu

 

to “OFF”.

 

 

Parts

 

 

 

 

See “Items in the extended menu” (page 96) for more

 

 

 

 

information.

 

 

 

 

See “Basic Operations of the Function Menu” (page 39)

 

 

for more information.

 

 

 

 

1 Power supply section

 

 

 

 

 

 

 

 

 

 

1 POWER switch

 

 

 

 

 

 

2 - AC IN connector

 

 

POWER

 

AC IN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

aPOWER (main power) switch

Press the : side to power on the unit. Press the a side to power off.

When using the unit, normally leave the POWER switch in the : (on) position, and use the on/standby button on the front panel to switch the unit between the operating state and standby state.

Note

Before turning the main power off, always check to be sure that the unit is in the standby state, and then press the main power switch to the a side.

b-AC IN connector

Connect to an AC power supply with the power cord (not supplied).

2 Analog audio signal input/output section

1 ANALOG AUDIO INPUT 1, 2 connectors

2 ANALOG AUDIO OUTPUT 1, 2 connectors

ANALOG AUDIO INPUT

 

ANALOG AUDIO OUTPUT

 

AUDIO MONITOR

 

 

 

 

 

1

2

1

2

R

L

3AUDIO MONITOR R, L connectors

aANALOG AUDIO INPUT 1, 2 connectors (XLR 3- pin, female)

These input analog audio signals.

With A1 INPUT or A2 INPUT on page P2 AUDIO, and A3 INPUT or A4 INPUT on page P3 AUDIO of the function menu (see page 41), you can select whether the signal input to connector 1 is assigned to audio channel 1or 3, and whether the signal input to connector 2 is assigned to audio channel 2 or 4.

You can set the reference input level with the maintenance menu item M37: AUDIO CONFIG (see page 108). (Factory default setting: +4 dB)

Microphone settings

If you have connected a microphone to this unit, you can set input level, AGC, and limiter values for the microphone with setup menu items 834, 839, 840, and 841 (see page 105).

Note

An unpleasant sound may be output if you have connected a microphone to the ANALOG AUDIO INPUT 1 or 2 connector and power the microphone on with the input level too high. Check the input level setting before connecting a microphone.

bANALOG AUDIO OUTPUT 1, 2 connectors (XLR

3-pin, male)

These output analog audio signals.

When the unit is shipped from the factory, the 1 connector is set to audio channel 1, and the 2 connector is set to audio channel 2. You can change these settings with setup menu item 824 ANALOG LINE OUTPUT SELECT (see page 104).

You can set the output level with the maintenance menu item M37: AUDIO CONFIG (see page 108). (Factory default setting: +4 dB)

Non-audio signals are muted.

cAUDIO MONITOR R, L connectors (XLR 3-pin,

male)

This outputs an audio signal for monitoring.

The monitored channel is selected with MONITR L and MONITR R on page P2 AUDIO of the function menu.

22 Rear Panel