See “Basic Operations of the Function Menu” (page 39) for more information.

3Digital audio signal input/output section

1DIGITAL AUDIO (AES/EBU) IN 1/2, 3/4 connectors

DIGITAL AUDIO (AES/EBU)

IN

1/2

3/4

OUT

1/23/4

2DIGITAL AUDIO (AES/EBU) OUT 1/2, 3/4 connectors

aDIGITAL AUDIO (AES/EBU) IN (digital audio input) 1/2, 3/4 connectors (BNC type)

These input AES/EBU format digital audio signals. The left connector (1/2) corresponds to audio channels 1 and 2, and the right connector (3/4) corresponds to audio channels 3 and 4.

bDIGITAL AUDIO (AES/EBU) OUT (digital audio output) 1/2, 3/4 connectors (BNC type)

These output AES/EBU format digital audio signals. When the unit is shipped from the factory, the 1/2 connector is set to audio channel 1/2, and the 3/4 connector is set to audio channel 3/4. You can change these settings with setup menu item 827 AES/EBU AUDIO OUTPUT SELECT (see page 105).

To treat the input and output signals of these connectors as non-audio signals, set the maintenance menu item M37: AUDIO CONFIG >M372: NON-AUDIO INPUT (recording) (see page 108) and setup menu item 823 NON- AUDIO FLAG PB (playback).

4 HDSDI signal input/output section

1 HDSDI INPUT connector

2HDSDI OUTPUT 1, 2 (SUPER) connectors

HDSDI INPUT

HDSDI OUTPUT

1

2

 

(SUPER)

aHDSDI INPUT (HDSDI signal input) connector (BNC type)

This inputs an HDSDI format video/audio signal.

bHDSDI OUTPUT 1, 2 (SUPER) (HDSDI signal output 1, 2 (superimpose)) connectors (BNC type)

These output HDSDI format video/audio signals. When editing with two PDW-HD1500 units, connect a cable between these connectors on the player unit and the HDSDI INPUT connector on the recorder unit.

You can superimpose timecodes, menu settings, error messages, or other information on the output of the HDSDI OUTPUT 2 (SUPER) connector with the setting for CHAR SEL on the HOME page of the function menu or with the setting for setup menu item 028 HD CHARACTER. You can always disable to superimpose the data independent of the setting for CHAR SEL with the setting for setup menu item 028.

See “Basic Operations of the Function Menu” (page 39)

 

 

 

for more information about the CHAR SEL settings.

 

 

 

2Chapter

item 028 HD CHARACTER.

 

 

See page 93 for more information about the setup menu

 

To treat the input and output signals of these connectors as

Names

 

non-audio signals, set the maintenance menu item M37:

and

AUDIO CONFIG >M372: NON-AUDIO INPUT

ofFunctions

(recording) (see page 108) and setup menu item 823 NON-

 

AUDIO FLAG PB (playback).

 

 

 

5 Timecode input/output section

Parts

 

 

 

1 TIME CODE IN connector

 

 

 

2 TIME CODE OUT

 

 

 

connector

 

 

TIME CODE

 

 

IN

OUT

 

 

 

 

 

 

aTIME CODE IN connector (BNC type)

This inputs an SMPTE timecode generated by an external device.

bTIME CODE OUT connector (BNC type)

This outputs the following timecode, depending on the operating state of this unit.

During playback: Playback timecode

During recording: The timecode from the internal timecode generator or the timecode input to the TIME CODE IN connector

When setup menu item 611 TC OUTPUT PHASE IN EE MODE is set to “muting”, no timecode is output.

Rear Panel 23