Name | Description | Options | Default |
On time | Number of seconds that the each air pulse lasts | 1.0 sec. | |
| during filter cleaning. |
|
|
| If |
|
|
| service department may ask you to change this |
|
|
| setting. |
|
|
Off time | Number of seconds between air pulses during | 1.0 sec. | |
| filter cleaning. |
|
|
| If |
|
|
| service department may ask you to change this |
|
|
| setting. |
|
|
| Slide Gate Options | (Only available on 7/50D Plus systems) |
|
|
| |
| Slide gate |
| When this option is enabled, the controller | disabled, | disabled |
|
|
|
| opens the slide gate between the station and | enabled |
|
|
|
|
| the receiver during the dump delay and during |
|
|
|
|
|
|
|
|
| |
|
|
| Enable this option if and only if the station has a |
|
|
|
|
|
| slide gate instead of a flapper and demand |
|
|
|
|
|
| switch. |
|
|
|
| Purge Options |
|
|
|
|
|
| Purge |
| When enabled, this option allows the system to | disabled, | disabled |
|
|
|
| empty the material line completely after every | enabled |
|
|
|
|
| convey to this station. The station’s pump |
|
|
|
|
|
| continues to draw without picking up material for |
|
|
|
|
|
| an extra period of time after conveying is |
|
|
|
|
|
| finished. |
|
|
|
|
|
| Enable this option if and only if you are using a |
|
|
|
|
|
| purge valve for this station. This option cannot |
|
|
|
|
|
| be used with a |
|
|
|
| Purge duration |
| Number of seconds allowed for purging. The | 20 sec. |
| |
|
|
| station’s vacuum valve remains open for the |
|
|
|
|
|
| convey time plus this time. |
|
|
|
|
|
| Adjust this setting to the amount of time |
|
|
|
|
|
| required for material to travel from the pickup |
|
|
|
|
|
| point (purge valve) to the station. |
|
|
|
| Purge valve |
| Number (address) for the purge valve used with | 0 (= not |
| |
|
|
| this station. |
| assigned) |
|
|
|
| Set this to match the number (address) for the |
|
|
|
|
|
| purge valve that services this station. If another |
|
|
|
|
|
| station has the purge valve that services this |
|
|
|
|
|
| station, enter the number of that station (range: |
|
|
|
|
|
|
|
|
| |
|
|
| station, enter the number (address) of that valve |
|
|
|
|
|
| (range: |
|
|
|
| Material Proofing Options |
|
|
|
| |
| Material proofing |
| When this option is enabled, the controller | disabled, | disabled |
|
|
|
| issues an alarm for the station if the number for | enabled |
|
|
|
|
| “Material set to” does not match the number for |
|
|
|
|
|
| the actual material. These numbers refer to |
|
|
|
|
|
| material lines. |
|
|
|
|
|
| Enable this option if and only if your facility has |
|
|
|
|
|
| installed the option of material proofing and you |
|
|
|
|
|
| want to check the material line connected to this |
|
|
|
|
|
| station. |
|
|
|
7/50D Plus or 7/50D Controller | Chapter 6: Configurable Settings | 76 |
