Sterling Plumbing 882.00254.00 instruction

Figure 8: Proper Controller and Remote Interface Connections

Black Power Flat Cable

Vacuum Tube

Grey Network Flat Cable

Power or Network Tap/Cable Drop

Part No. A0555195

One (1) Cord Required & is Connected, as Shown, to the Grey Network Flat Cable

Main Touch-Screen

Control Display

Blue Cable, 20 ft. (6 m)

One (1) Cord is Needed per Display, as Shown Connected to the Marked Terminals of the Main & Remote Control Boxes

Remote Touch-Screen

Control Display

ArmorBlock Mounting Plate Kit Part No. A0556696

7/50D Plus or 7/50D Controller

Chapter 3: Installation

25

Image 26

Sterling Plumbing 882.00254.00 specifications Proper Controller and Remote Interface Connections

Contents

SCC 7-Pump 50D & D Plus-Station Controllers Parts and Service Department Shipping Information Table of Contents Maintenance Controller Safety Tags Safety Symbols Used in this Manual SafetyHow to Use This Manual Wear Safety Glasses and Work Gloves Responsibility General Responsibility Operator Responsibility Maintenance ResponsibilityReporting a Safety Defect General Description Functional DescriptionModels Covered in This Manual Electrical Features Standard FeaturesMechanical Features Controller Features Safety Circuit Standards Optional FeaturesSafety Devices and Interlocks Fail Safe Operation Safety Device Lock-Outs Uncrating InstallationSystem Installation Overview Mounting the Control Panel Running KwikLink Cables Making Control Panel Power Drop Wiring ConnectionsElectrical Connections About KwikLink Flat Cables Installing KwikLink Cable Installing Assembled Mounting Plates Setting Up and Installing Mounting PlatesSetting Up Mounting Plates Terminating Cable Runs Discard the standard resistor cap to eliminate confusion Installing Inside KwikLink Connectors with Blank Caps Proper Termination Connections Addressing Armorblocks Addressing and Installing ArmorBlocksSetting Armorblock Addresses ArmorBlock Address Ranges Installing ArmorBlocks Using seal block to pierce cable Securing the Seal Block to the Cable Base Installing KwikLink Connectors Connecting the Controller to the Network Connecting the Remote Interface to the Main Controller Proper Controller and Remote Interface Connections Connecting the Power Supply Enclosure to the Network Proper Power Supply Enclosure Connections Connecting Vacuum Receivers to the Network 50D 4-Connector ArmorBlock Connections Plus Connections Connecting Vacuum Pumps and Filter Chambers to the Network Connecting Vacuum Pumps Proper Vacuum Pump Connections Connecting Filter Chambers Proper Filter Chamber Connections Connecting Central Alarms to the Network Proper Central Alarm Connections Alarm Horn C-O1 Setup Basic Menu Flow for Setup Setting Up the System Setting the Number of Stations and the Number of Pumps 50D Plus Screen shown Checking Addressing and Wiring for System Components Page Page Setting Up Alarm Silences Setting Up Pump Staging Setting Up Touch Switch Delay Setting Up Stations Setting Up a Single Station 50D Plus shown Copying Settings from One Station to Others To copy the selected station’s settings to one other station Setting Up Pumps Setting Up a Single PumpPage Copying Settings from One Pump to Others To copy the selected pump’s settings to one other pump To copy the current pump’s settings to all other pumps Finishing Setup Setting Up Passwords Page Initial Startup Starting and Stopping the System OperationOverview Basic Tasks Reviewing Station Status Color Label Description Reviewing Pump Status Color Label Description Logging On and Logging Off Enabling and Disabling Stations and Pumps Reviewing and Adjusting Basic Station Settings Reaching and Reading the Station Operator Screens Adjusting Convey Time and Dump Delay Navigating among the Station Operator Screens Activating and Stopping Priority Convey for a Station Changing the Mixture for a Remote Proportioning Valve Advanced Tasks Changing the Line with Material Proofing Reviewing and Resetting a Pump Hour Meter Transferring Stations to a Standby Pump Page Page Alarms Reviewing Alarms Clearing the Alarm Log Touch Continue Silencing Alarms Corrective Maintenance MaintenancePreventative Maintenance Network Scanner Module Considerations Memory Module Considerations Configurable SettingsOptions for Station Setup 50D Plus or 7/50D Controller Configurable Settings Blow Back Options Only available on 7/50D Plus systems Only available on 7/50D Plus systems 50D Plus or 7/50D Controller Configurable Settings Options for Pump Setup 50D Plus or 7/50D Controller Configurable Settings Troubleshooting General Troubleshooting Station Alarms Alarm message Possible cause Pump Alarms System Alarms Optional Components WarrantyAppendix Drawings and Diagrams Pump 50 station Controller with ??? Display Typical System Installation Layout 50D Plus or 7/50D Controller Appendix AC Voltage Spare Parts ListReturned Material Policy DC Voltage Controller Safety Tags Safety Tag InformationWarranty Returns Controller Identification Serial Number Tag Parts Department Service DepartmentTechnical Assistance Contact Information Sales Department