Proper Vacuum Pump Connections | Sterling Plumbing 882.00254.00

Figure 14: Proper Vacuum Pump Connections

Black Power Flat Cable

Vacuum Tube

Grey Network Flat Cable

ArmorBlock Mounting Plate Kit

Yellow Patch Cord, 20 ft. (6 m)Part No. A0556696 Part No. A0555190

Two (2) Cords Required

4 Input / 4 Output ArmorBlock

Part No. A0558296

ArmorBlock Base

Part No. A0555191

Vacuum Pump

7/50D Plus or 7/50D Controller

Chapter 3: Installation

31

Image 32

Sterling Plumbing 882.00254.00 specifications Proper Vacuum Pump Connections

Contents

SCC 7-Pump 50D & D Plus-Station Controllers Parts and Service Department Shipping Information Table of Contents Maintenance Controller Safety Tags Safety Symbols Used in this Manual SafetyHow to Use This Manual Wear Safety Glasses and Work Gloves Responsibility General Responsibility Operator Responsibility Maintenance ResponsibilityReporting a Safety Defect General Description Functional DescriptionModels Covered in This Manual Standard Features Mechanical FeaturesElectrical Features Controller Features Optional Features Safety Devices and InterlocksSafety Circuit Standards Fail Safe Operation Safety Device Lock-Outs Installation System Installation OverviewUncrating Mounting the Control Panel Making Control Panel Power Drop Wiring Connections Electrical ConnectionsRunning KwikLink Cables About KwikLink Flat Cables Installing KwikLink Cable Installing Assembled Mounting Plates Setting Up and Installing Mounting PlatesSetting Up Mounting Plates Terminating Cable Runs Discard the standard resistor cap to eliminate confusion Installing Inside KwikLink Connectors with Blank Caps Proper Termination Connections Addressing and Installing ArmorBlocks Setting Armorblock AddressesAddressing Armorblocks ArmorBlock Address Ranges Installing ArmorBlocks Using seal block to pierce cable Securing the Seal Block to the Cable Base Installing KwikLink Connectors Connecting the Controller to the Network Connecting the Remote Interface to the Main Controller Proper Controller and Remote Interface Connections Connecting the Power Supply Enclosure to the Network Proper Power Supply Enclosure Connections Connecting Vacuum Receivers to the Network 50D 4-Connector ArmorBlock Connections Plus Connections Connecting Vacuum Pumps and Filter Chambers to the Network Connecting Vacuum Pumps Proper Vacuum Pump Connections Connecting Filter Chambers Proper Filter Chamber Connections Connecting Central Alarms to the Network Proper Central Alarm Connections Alarm Horn C-O1 Setup Basic Menu Flow for Setup Setting Up the System Setting the Number of Stations and the Number of Pumps 50D Plus Screen shown Checking Addressing and Wiring for System Components Page Page Setting Up Alarm Silences Setting Up Pump Staging Setting Up Touch Switch Delay Setting Up Stations Setting Up a Single Station 50D Plus shown Copying Settings from One Station to Others To copy the selected station’s settings to one other station Setting Up Pumps Setting Up a Single PumpPage Copying Settings from One Pump to Others To copy the selected pump’s settings to one other pump To copy the current pump’s settings to all other pumps Finishing Setup Setting Up Passwords Page Initial Startup Starting and Stopping the System OperationOverview Basic Tasks Reviewing Station Status Color Label Description Reviewing Pump Status Color Label Description Logging On and Logging Off Enabling and Disabling Stations and Pumps Reviewing and Adjusting Basic Station Settings Reaching and Reading the Station Operator Screens Adjusting Convey Time and Dump Delay Navigating among the Station Operator Screens Activating and Stopping Priority Convey for a Station Changing the Mixture for a Remote Proportioning Valve Advanced Tasks Changing the Line with Material Proofing Reviewing and Resetting a Pump Hour Meter Transferring Stations to a Standby Pump Page Page Alarms Reviewing Alarms Clearing the Alarm Log Touch Continue Silencing Alarms Maintenance Preventative MaintenanceCorrective Maintenance Network Scanner Module Considerations Memory Module Considerations Configurable SettingsOptions for Station Setup 50D Plus or 7/50D Controller Configurable Settings Blow Back Options Only available on 7/50D Plus systems Only available on 7/50D Plus systems 50D Plus or 7/50D Controller Configurable Settings Options for Pump Setup 50D Plus or 7/50D Controller Configurable Settings Troubleshooting General Troubleshooting Station Alarms Alarm message Possible cause Pump Alarms System Alarms Optional Components WarrantyAppendix Drawings and Diagrams Pump 50 station Controller with ??? Display Typical System Installation Layout 50D Plus or 7/50D Controller Appendix Spare Parts List Returned Material PolicyAC Voltage DC Voltage Safety Tag Information Warranty ReturnsController Safety Tags Controller Identification Serial Number Tag Service Department Technical Assistance Contact InformationParts Department Sales Department