Manuals / Sun Microsystems / Computer Equipment / Server

Sun Microsystems T6320 D.3 Sun OpenGL for Solaris Software, D.4 Man Pages, host% fbconfig -list

Models: T6320

1 150

Download 150 pages 45.06 Kb

Page 141

D.3 Sun OpenGL for Solaris Software

Note – The XVR-50 graphics accelerator video composite sync is an XOR composite sync.

Note – Not all resolutions are supported by all monitors. Using resolutions that are not supported by the monitor may damage the monitor. Please refer to your monitor manuals for supported resolutions.

The default resolution is dictated either by EDID information from the connected monitor or by the console resolution that is set (see TABLE D-1). When no monitor is connected to supply EDID information, the default resolution is 1024 x 768 @ 75 Hz.

D.3 Sun OpenGL for Solaris Software

The Sun OpenGL 1.5 for Solaris software supports the XVR-50 graphics accelerator through software implementation.

D.4 Man Pages

The XVR-50 graphics accelerator man pages describe how you can query and set frame buffer attributes such as screen resolutions and visual configurations.

Use the fbconfig(1M) man page for configuring all Sun graphics accelerators. SUNWpfb_config(1M) contains XVR-50 device-specific configuration information. To get a list of all graphics devices on your system, type:

host% fbconfig -list

This example shows a list of graphics devices displayed:

Device-Filename	Specific Config Program
---------------	-----------------------
/dev/fbs/pfb0	SUNWpfb_config

Appendix D XVR-50 Graphics Accelerator D-3

Image 141

Sun Microsystems T6320 service manual D.3 Sun OpenGL for Solaris Software, D.4 Man Pages, host% fbconfig -list

Contents

Sun Microsystems, Inc Sun BladeTM T6320 Server Module Service ManualThis distribution may include materials developed by third parties 2. Sun Blade T6320 Server Module Diagnostics ContentsPreface 1. Sun Blade T6320 Server Module Product Descriptioniv Sun Blade T6320 Server Module Service Manual June 3. Replacing Hot-Swappable and Hot-Pluggable Components 4. Replacing Cold-Swappable ComponentsContents vi Sun Blade T6320 Server Module Service Manual June D. XVR-50 Graphics Accelerator A. SpecificationsIndex-1 IndexChecking Device Configuration D-5 HD15 Video Output Port D-6Preface Using UNIX CommandsTypographic Conventions Accessing Sun DocumentationShell Prompts http//docs.sun.com/app/docs/prod/blade.t6320Preface moduleThird-Party Web Sites Documentation, Support, and TrainingSun Welcomes Your Comments Section 1.4, “Additional Service Related Information” on page Section 1.2, “Support for RAID Storage Configurations” on pageSun Blade T6320 Server Module Product Description 1.1 Component OverviewFIGURE 1-1 Sun Blade T6320 Server Module With Chassis 1-2 Sun Blade T6320 Server Module Service Manual JuneFIGURE 1-2 Front and Rear Panels Front ViewRear View two connectors Four connector dongle cable UCP-4Three connector dongle cable UCP-3 RJ-45 serial USB two connectors 1-4 Sun Blade T6320 Server Module Service Manual Juneduring normal system operation 1-6 Sun Blade T6320 Server Module Service Manual June TABLE 1-1 Sun Blade T6320 Server Module Features ContinuedTABLE 1-2 Interfaces With the chassis and FIGURE A-2FB-DIMMs RAID Expansion Module Service processor http//docs.sun.com/app/docs/prod/blade.srvrwith NVRAM EEPROM with ILOM and ALOM Battery Hard drives Section 4.4, “Removing and Replacing the Service Processor” on pageReplacement Instructions 1-8 Sun Blade T6320 Server Module Service Manual JuneSection 4.3.1, “Removing the DIMMs” on pageBL = blade server module NEM1 NEM0 1.1.1 Multicore Processor Information1.2 Support for RAID Storage Configurations Uniform Command-Line Interface Users GuideSun StorageTek RAID Manager Software Users Guide 1.3 Finding the Serial Number 1.2.2 Sun Blade RAID 0/1 G2 Expansion Module1.2.1 Sun Blade RAID 5 Expansion Module FIGURE 1-6 Serial Number and MAC Address Location 1-12 Sun Blade T6320 Server Module Service Manual JuneMAC address Serial numberALOM CMT example 1-14 Sun Blade T6320 Server Module Service Manual June 1.4 Additional Service Related Informationsc showplatform Slot Number 5 Domain StatusSection 2.2, “Memory Configuration and Fault Handling” on page Sun Blade T6320 Server Module DiagnosticsSection 2.5, “Using the ILOM Web Interface For Diagnostics” on page Section 2.3, “Interpreting System LEDs” on pageSun Integrated Lights out Manager 2.0 User’s Guide 2.1 Sun Blade T6320 Server Module Diagnostics OverviewChapter 2 Sun Blade T6320 Server Module Diagnostics SP/faultmgt FIGURE 2-1 Diagnostic FlowchartSection 2.5.3, “Displaying System Faults” on page connected and the chassis has powerSystem Faults” on Check the OK LED. The OK LED is located on the front of the Sun BladeSection 4.2, “Common Procedures for Parts Replacement” on page FRU-name deemed faulty and disabledSection 2.7.2, “Clearing PSH Detected Faults” on page Section 2.7.3, “Clearing the PSH Fault From the ILOM Logs” on page2.2 Memory Configuration and Fault Handling 2.2.1 FB-DIMM Configuration GuidelinesWhen Upgrading Memory When Replacing Faulty FB-DIMMs 2.2.1.1 DIMM Installation RulesFour DIMMs installed FIGURE 2-3 FB-DIMM Installation RulesEight DIMMs installed Sixteen DIMMs installedFB-DIMM Configuration and Installation You can also use TABLE 2-2 to identify the DIMMs you want to removeFIGURE 2-4 DIMM Locate Button and DIMM LEDs 2.2.1.2 Memory Fault Handling 2.2.1.3 Troubleshooting Memory FaultsTABLE 2-2 FB-DIMM Configuration and Installation Continued 2.3.1 Front Panel LEDs and Buttons 2.3 Interpreting System LEDsFIGURE 2-5 Front Panel and Hard Drive LEDs The LEDs have assigned meanings, described in TABLEFront View TABLE 2-3 LED Behavior and MeaningTABLE 2-4 LED Behaviors With Assigned Meanings 2-14 Sun Blade T6320 Server Module Service Manual JuneChapter 2 Sun Blade T6320 Server Module Diagnostics TABLE 2-4 LED Behaviors With Assigned Meanings ContinuedTABLE 2-5 Front Panel Buttons 2.4 Using ILOM for Diagnosis and Repair Verification 2.3.2 Ethernet Port LEDshttp//docs.sun.com/app/docs/prod/blade.6000mod Service Required LED FRU LEDs FRUID PROMs Event Logs Alerts ILOMfru at location is OK 2.5 Using the ILOM Web Interface For DiagnosticsILOM CLI -show /SP/network 2.5.1 Changing POST Settings With the ILOM Web Interface1. Select the Remote Control tab and the Diagnostics tab FIGURE 2.5.2 Changing POST Settings With the ILOM CLI 2.5.3 Displaying System Faults1. Type the show command to see the current POST settings 2.5.3.1 Viewing Fault Status Using the ILOM Web Interface 2.5.3.2 Viewing Fault Status Using the ILOM CLI FIGURE 2-11 Faulted Component ID WindowFIGURE 2-12 Component Management Page - Fault Status 2.5.4 Displaying the Environmental Status with the ILOM CLI show /SP/faultmgmtChapter 2 Sun Blade T6320 Server Module Diagnostics 3. Double click on the sensor reading that you want to check FIGURE2.5.6 Displaying FRU Information 2.5.6.1 Using the ILOM Web Interface to Display FRU Information1. Select the System Information and Components tabs 2. Click on the component to view the FRU information FIGURE2.5.6.2 Using the CLI to Display FRU Information Chapter 2 Sun Blade T6320 Server Module DiagnosticsFIGURE 2-15 Static FRU Information in the ILOM Web Interface show /SYS/MB At the - prompt, type the show commandsc showfru SYS/SP container 2.6.1 Controlling How POST Runs 2.6 Running POSTTABLE 2-6 Parameters Used For POST Configuration 2-32 Sun Blade T6320 Server Module Service Manual June FIGURE 2-16 Flowchart of ILOM Variables for POST Configuration2. Select the Diagnostics Tab 2.6.2.1 Using the Web Interface to Change POST Parameters3. Select the POST settings that you require 2.6.2 Changing POST Parameters6. Select a power control setting and Select Save FIGURE 5. Select the Remote Power Control TabFIGURE 2-17 Setting POST Parameters With the ILOM Web Interface 2-34 Sun Blade T6320 Server Module Service Manual JuneFIGURE 2-18 Changing Power Settings with the ILOM Web Interface 1. Verify the current post parameters with the show command. Type 2.6.2.2 Using the CLI to Change POST Parameters2. Type the set command to change the POST parameters show /HOST/diagcs MSG = test-error-message 3. Power cycle the server module to run POST2.6.3 Interpreting POST Messages 1. Interpret the POST messagesSee Section 2.9, “Managing Components With Automatic System Recovery 2.6.4 Clearing POST Detected FaultsCommands” on page show /SP/faultmgmt3. In the Actions menu, select Enable Component 2.6.4.1 Clearing Faults With the Web Interface1. Select the tabs System Information and Components tabs FIGURE 2. Select the radio button for the component that you must clearPOST detected faults 2.6.4.2 Clearing Faults With the ILOM CLI3. Reboot the server module show /SP/faultmgmt2.6.4.3 Clearing Faults Manually with ILOM 2.7 Using the Solaris Predictive Self-Healing Feature2.6.4.4 Clearing Hard Drive Faults show /SP/faultmgmt2.7.1.1 Using the fmadm faulty Command 2.7.1 Identifying Faults With the fmadm faulty and fmdump Commands# fmdump 2.7.1.2 Using the fmdump Command2.7.2 Clearing PSH Detected Faults c. Follow the suggested actions to repair the faultb. Type the message ID in the SUNW-MSG-ID field, and press Lookup 2.7.3 Clearing the PSH Fault From the ILOM Logs 1. After replacing a faulty FRU, boot the system3. Clear the fault from all persistent fault records 2.8.1 Checking the Message Buffer 2.8 Collecting Information From Solaris OS Files and Commands1. Log in as superuser show /SP/faultmgmt2. Type the syslogd command 2.9 Managing Components With Automatic System Recovery Commands1. Log in as superuser 2. Type the following command 3. If you want to view all logged messages, type this command2-48 Sun Blade T6320 Server Module Service Manual June TABLE 2-8 ASR Commands1. At the - prompt, type the show command 2.9.1 Displaying System Components With the show /SYS Command2.10 Exercising the System With SunVTS 2.10.1 Checking SunVTS Software Installation2. Enable the remote display. On the display system, type 2.10.2 Exercising the System Using SunVTS Software2.10.3 Steps for Exercising the System With SunVTS Software SunVTS 6.4 Test Reference Manual for SPARC Platforms2-52 Sun Blade T6320 Server Module Service Manual June 4. Start SunVTS software# /opt/SUNWvts/bin/sunvts -display display-system0 FIGURE 2-20 SunVTS BI7. Start testing 5. Optional Select the test category you want to run6. Optional Customize individual tests 2.11.1 To Reset the Root Password to the Factory Default 2.11 Resetting the Password to the Factory Default4. Change the root password 1. Remove the server module from the modular system chassisChapter 2 Sun Blade T6320 Server Module Diagnostics Page 3.1 Hot-Pluggable Hard Drives Replacing Hot-Swappable and Hot- Pluggable Components3.2 Hot-Plugging a Hard Drive Section 3.1, “Hot-Pluggable Hard Drives” on page2. Type the Solaris OS commands required to stop using the hard drive 3.2.1 Rules for Hot-Plugging3.2.2 Removing a Hard Drive 5. Grasp the latch and pull the drive out of the drive slot 4. Push the latch release button FIGUREAmber LED Service Action Required Green LED3.2.3 Replacing a Hard Drive or Installing a New Hard Drive 1. If necessary, remove the hard drive filler panel2. Slide the drive into the bay until it is fully seated FIGURE 4. Perform administrative tasks to reconfigure the hard drive 3.3 Adding PCI ExpressModules3. Close the latch to lock the drive in place 3-6 Sun Blade T6320 Server Module Service Manual June Section 4.1, “Safety Information” on page 4.1 Safety InformationSection 4.2, “Common Procedures for Parts Replacement” on page Section 4.4, “Removing and Replacing the Service Processor” on page4.1.1 Safety Symbols 4.1.2 Electrostatic Discharge Safety4.1.2.1 Using an Antistatic Wrist Strap 4.1.2.2 Using an Antistatic Mat 4.2 Common Procedures for Parts Replacement4.2.1 Required Tools 4.2.2 Shutting Down the System4. Shut down the Solaris OS using the shutdown 1Mcommand 4.2.3 Using the ILOM Web Interface to Shut Down the Server Module1. Log in as superuser or equivalent 2. Notify affected users4.2.4 Using the ILOM CLI to Shut Down the Server Module FIGURE 4-1 Powering Off the Server Module with the ILOM Web InterfaceChapter 4 Replacing Cold-Swappable Components 2. At the ILOM - prompt, type the set /SYS/PS0 two connectors Four connector dongle cable UCP-4Three connector dongle cable UCP-3 RJ-45 serial USB two connectors DB-9 serial, male TTYA4-8 Sun Blade T6320 Server Module Service Manual June 4. Open the ejector levers FIGURE6. Set the server module on an antistatic mat 7. Attach an antistatic wrist strapFIGURE 4-4 Stack Five Server Modules or Fewer 4.3 Removing and Replacing DIMMs 4.3.1 Removing the DIMMs9. Lift the cover off the chassis FIGURE 4-6 DIMM Locate Button and DIMM LEDs 2. Locate the DIMMs that you want to replace FIGUREFB-DIMM Configuration Sixteen DIMMs installedFB-DIMM Configuration 2. Ensure that the connector ejector tabs are in the open position 1. Place the replacement DIMMs on an antistatic mat4.3.2 Replacing the DIMMs 6. Place DIMMs on an antistatic mat4.4 Removing and Replacing the Service Processor 4.4.1 Removing the Service Processor4.3.2.1 Verifying DIMM Installation 4. Place the service processor card on an antistatic mat The PROM is keyed to ensure proper orientation 4.4.2 Replacing the Service Processor3. Place the service processor on an antistatic mat 4.5 Removing and Replacing the Battery on the Service Processor4.5.1 Replacing the Battery on the Service Processor 1. Remove the replacement battery from the packageFIGURE 4-11 Removing the Battery From the Service Processor 4.6 Replacing or Installing the Sun Blade RAID 5 Expansion Module Removing the RAID 5 Expansion Modulehttp//docs.sun.com/app/docs/prod/blade.6000disk~blade6000dskmod 2. Lift the card free from the connector 4.6.1 Installing the RAID 5 Expansion Module3. Lift the REM free from the gray plastic standoff 1. Place the card under the tabs of the gray plastic standoff FIGURE1. Power-up the computer and storage systems Verifying the RAID 5 Expansion Module Installationa. Ensure that all hard disk drives are securely installed d. Power-on the computer systemIn the following example, the HBA is the first device that is listed 5. Return to the root node by using the unselect-dev command 4.6.2 Configuring the RAID 5 Expansion ModuleUniform Command-Line Interface User’s Guide 4.6.3 Creating a Bootable Array With the RAID 5 Expansion Module4.7 Removing and Replacing the Sun Blade G2 RAID 0/1 Expansion Module 4.6.4 Additional Information4-26 Sun Blade T6320 Server Module Service Manual June 4.7.1 Replacing the RAID 0/1 Expansion Module1. Place the card under the tabs of the gray plastic standoff FIGURE FIGURE 4-14 Removing the RAID Expansion Module4.7.2 Verifying the RAID 0/1 Expansion Module Installation FIGURE 4-15 Replacing the RAID 0/1 Expansion ModuleChapter 4 Replacing Cold-Swappable Components 4.8.2 Reinstalling the Server Module in the Chassis 4.8 Finishing Component Replacement4.8.1 Replacing the Cover 1. Place the cover on the chassisThe ILOM software boots The server module powers on with 3.3v standby powerFIGURE 4-17 Inserting the Server Module in the Chassis Chapter 4 Replacing Cold-Swappable Components4-30 Sun Blade T6320 Server Module Service Manual June A.1 Physical Specifications SpecificationsSection A.1, “Physical Specifications” on page A-1 Section A.2, “Motherboard Block Diagram” on page A-3Operating Temperature and Altitude A.1.1 System Environmental SpecificationsNon-Operating Temperature and Altitude A-2 Sun Blade T6320 Server Module Service Manual JuneAppendix A Specifications A-3 A.2 Motherboard Block DiagramA-4 Sun Blade T6320 Server Module Service Manual June “About Creating a Bootable Array on a SPARC System” on page Creating a Bootable Array With the Sun Blade RAID 5 Expansion Module“Creating a Bootable Array Task Map” on page “Modifying the Miniroot Directory On the Install Server” on pageB.1 About Creating a Bootable Array on a SPARC System B.2 Creating a Bootable Array Task Map1. Install and connect the HBA and disk drives 6. Modify two locations on the network install server B.3 Modifying the Miniroot Directory On the Install Server7. Build a logical drive on which to install the Solaris 10 5/08 OS SUNWaac StorMan SUNWgccruntimeTo Modify the Miniroot Directory # pkgadd -R installdirpath/Solaris10/Tools/Boot -d. SUNWaac To Modify the Product Installation Directory# pkgadd -R installdirpath/Solaris10/Tools/Boot -d. SUNWgccruntime # pkgadd -R installdirpath/Solaris10/Tools/Boot -d. StorManTo Create a Logical Drive Using a Network Install Server B.5 Building a Logical Drive On Which to Install the Solaris OS“To Create a Logical Drive Using a Network Install Server” on page “To Create a Logical Drive Without a Network Install Server” on pageLabeling the drive Partitioning the drive Preparing a file system 4. Insert the path to your CDROM drive To Create a Logical Drive Without a Network Install ServerSC network configuration is IP Address Gateway address Netmask Ethernet Address 00144FE5AD6BTo Delete a Logical Drive on the REM To delete a logical drive on the REM, use the DELETE card-number To Label the Newly Created Logical DriveB.6 Next Steps # format# init Uniform Command-Line Interface User’s Guide B.6.1 Additional Informationhttp//docs.sun.com/app/docs/coll/dsk-cntrl Sun StorageTek RAID Manager Software User’s GuideC.1 Preparing to Install the Solaris OS Installing the Solaris OS and the RAID 5 Expansion Module DriverTo Prepare to Install the Solaris OS “Preparing to Install the Solaris OS” on pageTo Install the RAID 5 Expansion Module Driver With the Solaris OS C.2 Installing the RAID 5 Expansion Module Driver With the Solaris OS2. Specify that you want to perform a Manual Reboot 3. Use the df command to verify the following5. Apply the HBA driver package, SUNWaac 7. Reboot the system6. Apply any patches that are specifically required for the system # rebootC.3.1 Additional Information C.3 Next StepsUniform Command-Line Interface User’s Guide http//docs.sun.com/app/docs/prod/stortek.raid.hbaSection D.1, “Features” on page D-1 D.1 FeaturesSection D.6, “Default Color Depth” on page D-4 Section D.7, “Checking Device Configuration” on page D-5D.2 Video Formats host% fbconfig -res \?host% fbconfig -list D.3 Sun OpenGL for Solaris SoftwareD.4 Man Pages To access the fbconfig man page, type D.6 Default Color DepthTo access the XVR-50 graphics accelerator man page, type 8. Set the desired screen resolution. For example, typeD.7 Checking Device Configuration host% fbconfig -dev pfb0 -propt2. Log out and then log back in for the change to take effect D.8 HD15 Video Output Port host% fbconfig -dev pfb0 -prconfIndex Page Page Page UltraSPARC T1 processor and PSH actions, 2-5 DIMMsvideo formats, HD15, D-2 video, Sun XVR-50, D-1 voltage and current sensor status, displayingIndex-6 Sun Blade T6320 Server Module Service Manual June