SUPER MICRO Computer AS 1020C-3 Connecting the Control Panel

5-6

AS1020C-3 User's Manual

Figure 5-2. Front Control Panel Header Pins (JF1)

Connecting the Control Panel

JF1 contains header pins for various fro nt control panel connectors. See Figure

5-2 for the pin locations of th e various front control panel buttons an d LED indica-

tors and refer to section 5-9 for details. Note that even and odd numbered pins

are on opposite sides of each header.

All JF1 wires have been bundled into single keyed ri bbon cable to simplify their

connection. The red wire in the r ibbon cable plugs into pin 1 of JF1. Connect

the other end of the cable to the Contro l Panel printed circuit board, located just

behind the system status LEDs in the chassis.

See the Connector Deﬁ nitions section in this chapter for details and pin descrip -

tions of JF1.

NMI

x (key)

Vcc

Reset

Power

Ground

x (key)

Power LED

HDD LED

NIC1

NIC2

OH/Fan Fail LED

Power Fail LED

Ground

2 1

20 19

Contents

Main Printed in the United States of America Manual Revision 1.0 Release Date: October 13, 2006 Preface About This Manual Manual Organization Page Page vi Table of Contents Preface Chapter 1: Introduction Chapter 2: Server Installation Chapter 3: System Interface Chapter 4: System Safety Chapter 5: Advanced Serverboard Setup vii viii Chapter 6: Advanced Chassis Setup ix Chapter 7: BIOS Appendices: Page 1-1 Chapter 1 Introduction 1-1 Overview 1-2 Ser verboa rd Featur es Page 1-4 1-3 Server Chassis Features System Power Serial Attached SCSI (SAS) Subsystem Control Panel I/O Backplane Cooling System nVidia nForce Pro 2200 1-4 Contacting Supermicro Headquarters Europe Asia-Paci c 2-1 Chapter 2 Server Installation 2-1 Overview 2-2 Unpacking the System 2-3 Preparing for Setup 2-2 Warnings and Precautions! !! Rack Precautions Server Precautions Rack Mounting Considerations 2-4 Installing the Rack Rails 2-4 Installing the System into a Rack Identifying the Sections of the Rails 2-5 Installing the Chassis Rails 2-6 Installing the Server into the Rack Page 2-8 2-5 Checking the Serverboard Setup 2-9 2-6 Checking the Drive Bay Setup 2-10 3-1 Chapter 3 System Interface 3-1 Overview 3-2 Control Panel Buttons 3-3 Control Panel LEDs 3-4 SAS Drive Carrier LEDs Page 4-1 Chapter 4 System Safety 4-1 Electrical Safety Precautions 4-2 4-2 General Safety Precautions 4-3 4-3 ESD Precautions 4-4 4-4 Operating Precautions OR 5-1 Chapter 5 Advanced Serverboard Setup 5-1 Handling the Serverboard Precautions Unpacking 5-2 5-3 Processor and Heatsink Installation CPU Backplates 5-2 Mounting the Serverboard into a Chassis 5-3 Installing the Processor Page 5-5 5-4 Connecting Cables Connecting Data Cables Connecting Power Cables 5-6 Connecting the Control Panel 5-7 5-5 I/O Ports 5-6 Installing Memory CAUTION 5-8 5-9 5-7 Adding PCI Cards 5-10 AS1020C-3 User's Manual 5-8 Serverboard Details Figure 5-5. H8DCR-3 Serverboard Layout (not drawn to scale) Note: Jumpers not indicated are for test purposes only. 5-11 H8DCR-3 Quick Reference Jumpers Description Default Setting Connectors Description Onboard Indicators Description 5-12 5-9 Connector De nitions ATX Power Connector Processor Power Connector Auxiliary Power Connector NMI Button 5-13 Overheat/Fan Fail LED NIC1 LED NIC2 LED HDD LED 5-14 Reset Button Power Button Universal Serial Bus Ports (USB0/1) LAN1/2 (Ethernet Ports) 5-15 Fan Headers Serial Ports Extra USB Headers Chassis Intrusion 5-16 ATX PS/2 Keyboard and PS/2 Mouse Ports PS_SMBUS Overheat LED Power LED/Speaker 5-17 Wake-On-LAN Wake-On-Ring SMBus Header Alarm Reset Header 5-18 Power Fail Connector Compact Flash Power Connector JSLED1 Header I2C for SAS Connector 5-10 Jumper Settings Explanation of Jumpers CMOS Clear 5-20 I2C to PCI Enable/Disable 3rd Power Supply Fail Signal Enable/Disable Compact Flash Master/Slave VGA Enable/Disable 5-21 Watch Dog Enable/Disable Onboard Speaker Enable/ Disable SAS Controller Enable/ Disable 5-22 PCI-X Slot Frequency Select LAN1/2 Enable/Disable 5-23 5-11 Onboard Indicators LAN1/LAN2 LEDs +3.3V Standby LED SAS Activity LEDs 5-24 5-12 Floppy, IDE and SAS Connections Floppy Connector 5-25 IDE Connectors SAS Ports 5-26 5-13 Enabling SAS RAID Serial Attached SCSI (SAS) Enabling SAS RAID 5-27 SAS Controller Utility Creating a RAID Array Page 5-29 Additional Functions 5-30 5-14 Installing Drivers 6-1 Chapter 6 Advanced Chassis Setup Tools Required 6-1 Static-Sensitive Devices Precautions 6-2 6-2 Control Panel 6-3 6-3 System Fans System Fan Failure Replacing System Cooling Fans 6-4 6-4 Drive Bay Installation/Removal Removing the Front Bezel 6-5 Accessing the Drive Bays 6-6 Serial Attached SCSI (SAS) Drive Installation 6-7 6-8 CD-ROM and Floppy Drive Installation 6-9 6-5 Power Supply Power Supply Failure Removing/Replacing the Power Supply Page 7-1 Chapter 7 BIOS 7-1 Introduction Starting the Setup Utility 7-2 Main Menu 7-3 Advanced Settings Menu Page Page Page Page Page Page Page Hyper Transport Con guration AMD PowerNow Con guration Page Page Page 7-4 Boot Menu OS Installation 7-5 Security Menu 7-6 Exit Menu Page Appendix A BIOS Error Beep Codes A-1 A-1 AMIBIOS Error Beep Codes Beep Code Error Message Description Page B-1 Appendix B BIOS POST Checkpoint Codes B-1 Uncompressed Initialization Codes B-2 B-2 Bootblock Recovery Codes The bootblock recovery checkpoint codes are listed in order of execution: B-3 B-3 Uncompressed Initialization Codes B-4 B-5 B-6 B-7 Page Appendix C System Speci cations