Manuals / Brands / TV and Video / Satellite TV System / TechniSat / TV and Video / Satellite TV System

TechniSat DIGITY CI Operating Manual 7.5.2 Delete all programmes, 7.5.3 Updating software

1 50

Download 50 pages, 2.07 Mb

7.5.2 Delete all programmes

This function allows you to delete totally the programme

memory banks.

> Use the arrow keys up/down to mark the line Delete

all programmes.

> Press OK. The message “Do you really want to delete

all programmes?” will be displayed

Use the arrow keys left/right to indicate Yes or

Abort.

> Confirm by pressing OK.

Please note any messages displayed on your screen.

7.5.3 Updating software

In addition, you have the facility to update the operating

software of your receiver via satellite (ASTRA 19° East).

> Use the arrow keys up/down to mark the item

Update software.

> Press OK. The sub-menu Update software will be

displayed.

(Fig. 7-15)

To update your software, mark the item Update

software.

> Use the OK key to switch the software update function

On.

> Press the Menu key to return to normal operation.

In order for the new software to be downloaded

overnight, the receiver must remain in stand-by

mode. The download procedure is indicated by a

blinking LED light on the unit.This procedure

must not be interrupted by switching the unit on

or off, nor may it be disconnected from the mains

power supply.

> To start the update of the operating software manually,

press the red function key (Test) in the menu

Software Update .

To download any new software that may be available,

follow the instructions displayed on your screen.

Should the parameters of the data channel used to download

software updates have changed, you can correct them in this

menu as described under Point 7.4.3 (manual programme

search). Current transponder data can be obtained from your

specialist retailer. In general, however, you should not make

any changes in this menu.

Note:

This function should not be activated if you have

made changes in the menues Basic Settings

and LNB configuration, as any changes made

there would be deleted when this function is

performed, and you would have to repeat the

changes there

32

(Fig. 7-15)

bed_anl_DIGITY CI_Quark3_en.qxd 31.01.03 16:47 Seite 32

Contents

Main Operating Manual DDIIGGIITTYY CCII 1 Contents Page 2 Illustrations Remote control Front panel Rear panel 3 Please read this first Important operating information Environmental note: Safety Note: When not in operation: Connecting the DVB receiver to a satellite installation VCRAnalogue Receiver 4 Connections 4.1 Mains power connection 4.2 External unit 4.2.1 Single unit operation 4.2.2 Operating an additional receiver in a single- receiver installation 5 Installation 5.1 OSD language 5.2 Basic settings (Fig. 5-2) (Fig. 5-3) 5.3 Audio/Video settings (Fig. 5-4) (Fig. 5-5) 5.3.1 Image format TV set: 5.3.2 Language (Audio signal) 5.4 LNB setting/Adjusting to external unit/Satellite selection 5-6) (Fig. 5-7) (Fig. 5-8) 5.4.1 Switching DiSEqC on and off 5.4.2 Setting the switching matrix and the LNB characteristics 5.4.3 Additional Settings (Fig. 5-9) 5.4.4 Rotating antenna 6 Operation 6.1 Switching on and off 6.2 Programme selection 6.2.1 Using the Programme keys up/down 6.2.2 Using the numeric keys 6.2.3 Using the programme list (Fig. 6-1) 6.2.3.1 Selecting a list (Fig. 6-2) (Fig. 6-3) 6.3 Volume control 6.4 Reception of encrypted programmes 6.4.1 Multifeed options (Fig. 6-5) (Fig. 6-8) 6.5 Selecting a different language 6.6 Switching between TV and Radio 6.7 Return to previous programme 6.8 Display clock and programme information 6.9 Additional programme information 6.10 Transponder Information (Fig. 6-9) (Fig. 6-10) 6.11 Electronic Programme Guide 6.11.1 Calling up the Electronic Programme Guide 6.12 Timer 6.12.1 Programming via EPG: (Fig. 6-11) 6.12.2 Manual programming/Changing timer set- tings (Fig. 6-12) Page 6.13 Video text 6.13.1 Using the video text decoder of your television set 6.13.2 Using the internal video text decoder (Fig. 6-14) 7 Changing basic programming 7.1 Configuring the programme list (Fig. 7-3) 7.1.1 Calling up the programme list 7-1) 7.1.3 Deleting programmes 7.1.3.1 Deleting from the Favourites list 7.1.3.2 Deleting from the Total list 7.1.4 Sorting programmes (Fig. 7-5). 7.1.5 Blocking access to programmes (parental control) 7.2 Changing the PIN (Fig. 7-6) 7.3 Unblocking access control for individual programmes 7.4 Programme Search (Fig. 7-7) (Fig. 7-8) 7.4.1 Satellite (Fig. 7-9) 7.4.2 Transponder (Fig. 7-10) 7.4.3 Manual search (Fig. 7-11) 7.4.4 Integrating programmes after a search (Fig. 7-12) 7.5 Restoring basic programming/ Delete all (Fig. 7-13) (Fig. 7-14) 7.5.1 Activating default setting 7.5.2 Delete all programmes 7.5.3 Updating software (Fig. 7-15) 7.6 System configuration 7.7 Encryption system (Fig. 8-3) (Fig. 8-1) and switch the 8 Operation in conjunction with a rotary antenna (Fig. 8-2) 8.1.2 Setting Eastern limit 8.1.3 Setting Western limit 8.2 Geo-positioning (Fig. 8- 9) 8.3 Setting the satellite position 8.3.1 Selecting satellite positions 8.3.1.1 Selecting a pre-programmed satellite position (Fig. 8-10) 8.3.1.2 Setting user-defined satellite positions (User Satellite) (Fig. 8-11) 8.3.2 Adjusting the satellite antenna 8.3.2.1 Test-Transponder/LNB-configuration (Fig 8-12) 8.3.2.2 Antenna manual adjustment 8.3.2.3 Automatic fine adjustment (Autofocus) 8.3.3 Saving satellite positions (Fig. 8-14) (Fig. 8-15) (Figs. 8- 16 and 8-17) 8.4 List of current satellites 8.5 Deleting a satellite position 8.6 Reference position 9 Technical Terms Page Page 10 Technical data Page 11 Trouble-shooting guide ? Problem Possible cause Solution 12 Annexure Co-ordinates of selected German cities (1) Co-ordinates of selected German cities (2) Co-ordinates of selected German cities (3) For everyday use Switching on and off Programme selection Using the programme keys up/down Using the numeric keys