TechniSat DIGITY CI Operating Manual 6 Operation

15

LOF high band

In this line, use the numeric keys to enter the LOF of the

high band of your LNB.

Switchover LOF low//high

In this line, use the numeric keys to enter the frequency at

which your LNB switches from the low band to the high band.

Press OK to accept the setting and store it in memory.

Signal/Quality

If you have entered the parameters of the test transponder

correctly, this line will indicate the signal strength and quality.

5.4.4 Rotating antenna

If you are operating the receiver in conjunction with a rotating

antenna driven by a DiSEqC motor ( Level 1.2), switch the

DiSEqC Control (Point 5.4.1) on and please note Point

8of the operating manmual.

6 Operation

6.1 Switching on and off

> Switch the receiver on by pressing the On/Standby

key on the front panel of the unit, or on the remote

control.

> Pressing the same key again - on the unit or on the

remote control - will switch the receiver off again.

> The unit is now in standby mode, ready for use.

Please note:

When switching the receiver off, all current settings are

automatically stored in memory. For this reason the

unit can only be switched on again after a period of

approx. 15 seconds.

6.2 Programme selection

6.2.1 Using the Programme keys up/down

> You can switch from one programme to another, one

slot at a time, using the programme keys up/down

either on the receiver itself or on the remote control

unit.

6.2.2 Using the numeric keys

> You can use the numeric keysto enter the desired

programme number directly.

For example:

1for programme slot 1

1, then 4for programme slot 14

2, then 3, then 4for programme slot 234

bed_anl_DIGITY CI_Quark3_en.qxd 31.01.03 16:47 Seite 15

Contents

Main Operating Manual DDIIGGIITTYY CCII 1 Contents Page 2 Illustrations Remote control Front panel Rear panel 3 Please read this first Important operating information Environmental note: Safety Note: When not in operation: Connecting the DVB receiver to a satellite installation VCRAnalogue Receiver 4 Connections 4.1 Mains power connection 4.2 External unit 4.2.1 Single unit operation 4.2.2 Operating an additional receiver in a single- receiver installation 5 Installation 5.1 OSD language 5.2 Basic settings (Fig. 5-2) (Fig. 5-3) 5.3 Audio/Video settings (Fig. 5-4) (Fig. 5-5) 5.3.1 Image format TV set: 5.3.2 Language (Audio signal) 5.4 LNB setting/Adjusting to external unit/Satellite selection 5-6) (Fig. 5-7) (Fig. 5-8) 5.4.1 Switching DiSEqC on and off 5.4.2 Setting the switching matrix and the LNB characteristics 5.4.3 Additional Settings (Fig. 5-9) 5.4.4 Rotating antenna 6 Operation 6.1 Switching on and off 6.2 Programme selection 6.2.1 Using the Programme keys up/down 6.2.2 Using the numeric keys 6.2.3 Using the programme list (Fig. 6-1) 6.2.3.1 Selecting a list (Fig. 6-2) (Fig. 6-3) 6.3 Volume control 6.4 Reception of encrypted programmes 6.4.1 Multifeed options (Fig. 6-5) (Fig. 6-8) 6.5 Selecting a different language 6.6 Switching between TV and Radio 6.7 Return to previous programme 6.8 Display clock and programme information 6.9 Additional programme information 6.10 Transponder Information (Fig. 6-9) (Fig. 6-10) 6.11 Electronic Programme Guide 6.11.1 Calling up the Electronic Programme Guide 6.12 Timer 6.12.1 Programming via EPG: (Fig. 6-11) 6.12.2 Manual programming/Changing timer set- tings (Fig. 6-12) Page 6.13 Video text 6.13.1 Using the video text decoder of your television set 6.13.2 Using the internal video text decoder (Fig. 6-14) 7 Changing basic programming 7.1 Configuring the programme list (Fig. 7-3) 7.1.1 Calling up the programme list 7-1) 7.1.3 Deleting programmes 7.1.3.1 Deleting from the Favourites list 7.1.3.2 Deleting from the Total list 7.1.4 Sorting programmes (Fig. 7-5). 7.1.5 Blocking access to programmes (parental control) 7.2 Changing the PIN (Fig. 7-6) 7.3 Unblocking access control for individual programmes 7.4 Programme Search (Fig. 7-7) (Fig. 7-8) 7.4.1 Satellite (Fig. 7-9) 7.4.2 Transponder (Fig. 7-10) 7.4.3 Manual search (Fig. 7-11) 7.4.4 Integrating programmes after a search (Fig. 7-12) 7.5 Restoring basic programming/ Delete all (Fig. 7-13) (Fig. 7-14) 7.5.1 Activating default setting 7.5.2 Delete all programmes 7.5.3 Updating software (Fig. 7-15) 7.6 System configuration 7.7 Encryption system (Fig. 8-3) (Fig. 8-1) and switch the 8 Operation in conjunction with a rotary antenna (Fig. 8-2) 8.1.2 Setting Eastern limit 8.1.3 Setting Western limit 8.2 Geo-positioning (Fig. 8- 9) 8.3 Setting the satellite position 8.3.1 Selecting satellite positions 8.3.1.1 Selecting a pre-programmed satellite position (Fig. 8-10) 8.3.1.2 Setting user-defined satellite positions (User Satellite) (Fig. 8-11) 8.3.2 Adjusting the satellite antenna 8.3.2.1 Test-Transponder/LNB-configuration (Fig 8-12) 8.3.2.2 Antenna manual adjustment 8.3.2.3 Automatic fine adjustment (Autofocus) 8.3.3 Saving satellite positions (Fig. 8-14) (Fig. 8-15) (Figs. 8- 16 and 8-17) 8.4 List of current satellites 8.5 Deleting a satellite position 8.6 Reference position 9 Technical Terms Page Page 10 Technical data Page 11 Trouble-shooting guide ? Problem Possible cause Solution 12 Annexure Co-ordinates of selected German cities (1) Co-ordinates of selected German cities (2) Co-ordinates of selected German cities (3) For everyday use Switching on and off Programme selection Using the programme keys up/down Using the numeric keys