TechniSat DIGITY CI Operating Manual ?

Power supply:

Mains power adapter:

Power requirement:

< 22 W (in operation, horizontal

polarisation/ 400 mA LNB power)

< 12 W (in operation, excl. LNB)

< 10 W (Stand-by Mode)

Mains voltage:

180 V.... 250 V / 47...63 Hz AC

General:

Ambient temperature +15°C...+35°C

Humidity < 80%

Dimensions (WxDxH): 305 mm x 135 mm x 65 mm

Weight: 0,8 kg

11 Trouble-shooting guide

Dear customer,

we would like to point out once again that, if you experience

the following problem, you should first follow our suggested

solution before contacting the repair service.

The unit does not function properly (controls do

not respond, image frozen ...)

> Disconnect the mains power supply for approx. 5

seconds, then connect it again.

> Then switch the receiver on again.

If the problem persists, you should then contact your repair

service.

45

?

Your appliance carries the CE mark, and complies with all relevant EU

standards.

Subject to alteration without notice. Not responsible for printing errors. Correct

at 10/02

Copying and reproduction only with specific permission of the publisher.

TechniSat and DIGITY CI are registerd trade marks of

TechniSat Digital GmbH

P.O. Box 560

D-54541 Daun

Germany

www. technisat.de

bed_anl_DIGITY CI_Quark3_en.qxd 31.01.03 16:47 Seite 45

Contents

Main Operating Manual DDIIGGIITTYY CCII 1 Contents Page 2 Illustrations Remote control Front panel Rear panel 3 Please read this first Important operating information Environmental note: Safety Note: When not in operation: Connecting the DVB receiver to a satellite installation VCRAnalogue Receiver 4 Connections 4.1 Mains power connection 4.2 External unit 4.2.1 Single unit operation 4.2.2 Operating an additional receiver in a single- receiver installation 5 Installation 5.1 OSD language 5.2 Basic settings (Fig. 5-2) (Fig. 5-3) 5.3 Audio/Video settings (Fig. 5-4) (Fig. 5-5) 5.3.1 Image format TV set: 5.3.2 Language (Audio signal) 5.4 LNB setting/Adjusting to external unit/Satellite selection 5-6) (Fig. 5-7) (Fig. 5-8) 5.4.1 Switching DiSEqC on and off 5.4.2 Setting the switching matrix and the LNB characteristics 5.4.3 Additional Settings (Fig. 5-9) 5.4.4 Rotating antenna 6 Operation 6.1 Switching on and off 6.2 Programme selection 6.2.1 Using the Programme keys up/down 6.2.2 Using the numeric keys 6.2.3 Using the programme list (Fig. 6-1) 6.2.3.1 Selecting a list (Fig. 6-2) (Fig. 6-3) 6.3 Volume control 6.4 Reception of encrypted programmes 6.4.1 Multifeed options (Fig. 6-5) (Fig. 6-8) 6.5 Selecting a different language 6.6 Switching between TV and Radio 6.7 Return to previous programme 6.8 Display clock and programme information 6.9 Additional programme information 6.10 Transponder Information (Fig. 6-9) (Fig. 6-10) 6.11 Electronic Programme Guide 6.11.1 Calling up the Electronic Programme Guide 6.12 Timer 6.12.1 Programming via EPG: (Fig. 6-11) 6.12.2 Manual programming/Changing timer set- tings (Fig. 6-12) Page 6.13 Video text 6.13.1 Using the video text decoder of your television set 6.13.2 Using the internal video text decoder (Fig. 6-14) 7 Changing basic programming 7.1 Configuring the programme list (Fig. 7-3) 7.1.1 Calling up the programme list 7-1) 7.1.3 Deleting programmes 7.1.3.1 Deleting from the Favourites list 7.1.3.2 Deleting from the Total list 7.1.4 Sorting programmes (Fig. 7-5). 7.1.5 Blocking access to programmes (parental control) 7.2 Changing the PIN (Fig. 7-6) 7.3 Unblocking access control for individual programmes 7.4 Programme Search (Fig. 7-7) (Fig. 7-8) 7.4.1 Satellite (Fig. 7-9) 7.4.2 Transponder (Fig. 7-10) 7.4.3 Manual search (Fig. 7-11) 7.4.4 Integrating programmes after a search (Fig. 7-12) 7.5 Restoring basic programming/ Delete all (Fig. 7-13) (Fig. 7-14) 7.5.1 Activating default setting 7.5.2 Delete all programmes 7.5.3 Updating software (Fig. 7-15) 7.6 System configuration 7.7 Encryption system (Fig. 8-3) (Fig. 8-1) and switch the 8 Operation in conjunction with a rotary antenna (Fig. 8-2) 8.1.2 Setting Eastern limit 8.1.3 Setting Western limit 8.2 Geo-positioning (Fig. 8- 9) 8.3 Setting the satellite position 8.3.1 Selecting satellite positions 8.3.1.1 Selecting a pre-programmed satellite position (Fig. 8-10) 8.3.1.2 Setting user-defined satellite positions (User Satellite) (Fig. 8-11) 8.3.2 Adjusting the satellite antenna 8.3.2.1 Test-Transponder/LNB-configuration (Fig 8-12) 8.3.2.2 Antenna manual adjustment 8.3.2.3 Automatic fine adjustment (Autofocus) 8.3.3 Saving satellite positions (Fig. 8-14) (Fig. 8-15) (Figs. 8- 16 and 8-17) 8.4 List of current satellites 8.5 Deleting a satellite position 8.6 Reference position 9 Technical Terms Page Page 10 Technical data Page 11 Trouble-shooting guide ? Problem Possible cause Solution 12 Annexure Co-ordinates of selected German cities (1) Co-ordinates of selected German cities (2) Co-ordinates of selected German cities (3) For everyday use Switching on and off Programme selection Using the programme keys up/down Using the numeric keys