TechniSat DIGITY CI Operating Manual For everyday use

For everyday use

Switching on and off

> Switch the unit on by pressing the On/Stand-by key,

either on the receiver or on the remote control unit.

> Pressing the same key again, either on the receiver or

on the remote control unit, will switch the receiver off

again.

> The receiver is now in Stand-by mode.

Programme selection

Using the programme keys up/down

> Use the programme keys up/down to switch from

one programme to another, one slot at a time. You can

use the keys either on the receiver panel or those on

the remote control unit.

Using the numeric keys

> Enter the desired programme number using the

numeric keys. For example:

1for programme slot 1

1, then 4for programme slot 14

2, then 3, then 4for programme slot 234

When entering programme numbers with more than one

digit, you have approximately 3 seconds after pressing each

key to complete the entry.

If you wish to enter a number consisting of only one or two

digits, you can speed up the selection process by keeping the

key depressed a little longer on the last digit.

Volume control

> To control the volume of your receiver, use the keys

Volume + to increase the volume and Volume -to

decrease the sound volume.

> Press the key Sound on/off to switch the sound off

(mute), press the key again to switch sound on again.

TV/radio switching

The pre-programming of your receiver includes radio as well

as television programmes You can thus also enjoy your

favourite radio programmes in digital quality, by switching to

Radio mode. In this case the corresponding TV image is not

displayed, you will see a blank screen with the programme

name displayed.

> Use the TV/Radio key to switch the receiver to radio

mode.

The receiver will now switch to the radio programme

last selected.

> Press the TV/Radio key again to switch to the

television programme last selected.

50

bed_anl_DIGITY CI_Quark3_en.qxd 31.01.03 16:47 Seite 50

Contents

Main Operating Manual DDIIGGIITTYY CCII 1 Contents Page 2 Illustrations Remote control Front panel Rear panel 3 Please read this first Important operating information Environmental note: Safety Note: When not in operation: Connecting the DVB receiver to a satellite installation VCRAnalogue Receiver 4 Connections 4.1 Mains power connection 4.2 External unit 4.2.1 Single unit operation 4.2.2 Operating an additional receiver in a single- receiver installation 5 Installation 5.1 OSD language 5.2 Basic settings (Fig. 5-2) (Fig. 5-3) 5.3 Audio/Video settings (Fig. 5-4) (Fig. 5-5) 5.3.1 Image format TV set: 5.3.2 Language (Audio signal) 5.4 LNB setting/Adjusting to external unit/Satellite selection 5-6) (Fig. 5-7) (Fig. 5-8) 5.4.1 Switching DiSEqC on and off 5.4.2 Setting the switching matrix and the LNB characteristics 5.4.3 Additional Settings (Fig. 5-9) 5.4.4 Rotating antenna 6 Operation 6.1 Switching on and off 6.2 Programme selection 6.2.1 Using the Programme keys up/down 6.2.2 Using the numeric keys 6.2.3 Using the programme list (Fig. 6-1) 6.2.3.1 Selecting a list (Fig. 6-2) (Fig. 6-3) 6.3 Volume control 6.4 Reception of encrypted programmes 6.4.1 Multifeed options (Fig. 6-5) (Fig. 6-8) 6.5 Selecting a different language 6.6 Switching between TV and Radio 6.7 Return to previous programme 6.8 Display clock and programme information 6.9 Additional programme information 6.10 Transponder Information (Fig. 6-9) (Fig. 6-10) 6.11 Electronic Programme Guide 6.11.1 Calling up the Electronic Programme Guide 6.12 Timer 6.12.1 Programming via EPG: (Fig. 6-11) 6.12.2 Manual programming/Changing timer set- tings (Fig. 6-12) Page 6.13 Video text 6.13.1 Using the video text decoder of your television set 6.13.2 Using the internal video text decoder (Fig. 6-14) 7 Changing basic programming 7.1 Configuring the programme list (Fig. 7-3) 7.1.1 Calling up the programme list 7-1) 7.1.3 Deleting programmes 7.1.3.1 Deleting from the Favourites list 7.1.3.2 Deleting from the Total list 7.1.4 Sorting programmes (Fig. 7-5). 7.1.5 Blocking access to programmes (parental control) 7.2 Changing the PIN (Fig. 7-6) 7.3 Unblocking access control for individual programmes 7.4 Programme Search (Fig. 7-7) (Fig. 7-8) 7.4.1 Satellite (Fig. 7-9) 7.4.2 Transponder (Fig. 7-10) 7.4.3 Manual search (Fig. 7-11) 7.4.4 Integrating programmes after a search (Fig. 7-12) 7.5 Restoring basic programming/ Delete all (Fig. 7-13) (Fig. 7-14) 7.5.1 Activating default setting 7.5.2 Delete all programmes 7.5.3 Updating software (Fig. 7-15) 7.6 System configuration 7.7 Encryption system (Fig. 8-3) (Fig. 8-1) and switch the 8 Operation in conjunction with a rotary antenna (Fig. 8-2) 8.1.2 Setting Eastern limit 8.1.3 Setting Western limit 8.2 Geo-positioning (Fig. 8- 9) 8.3 Setting the satellite position 8.3.1 Selecting satellite positions 8.3.1.1 Selecting a pre-programmed satellite position (Fig. 8-10) 8.3.1.2 Setting user-defined satellite positions (User Satellite) (Fig. 8-11) 8.3.2 Adjusting the satellite antenna 8.3.2.1 Test-Transponder/LNB-configuration (Fig 8-12) 8.3.2.2 Antenna manual adjustment 8.3.2.3 Automatic fine adjustment (Autofocus) 8.3.3 Saving satellite positions (Fig. 8-14) (Fig. 8-15) (Figs. 8- 16 and 8-17) 8.4 List of current satellites 8.5 Deleting a satellite position 8.6 Reference position 9 Technical Terms Page Page 10 Technical data Page 11 Trouble-shooting guide ? Problem Possible cause Solution 12 Annexure Co-ordinates of selected German cities (1) Co-ordinates of selected German cities (2) Co-ordinates of selected German cities (3) For everyday use Switching on and off Programme selection Using the programme keys up/down Using the numeric keys