TOA Electronics FPS1000-12, FPS-S1U Input/Output connector information, Repackaging for Shipment

3.7.7 Input/Output connector information

The FPS1000 series uses male connector PCIB24W9M400A1, Positronic connector. To mate FPS1000 series to the load circuitry, use female connector PCIB24W9F400A1-S1031, Positronic connector. Refer to Table 3-4 and to the Outline drawing in chapter 2 for the connector pinout description.

Pin No	Function	Description
1,2,4	+V	Positive output voltage. Maximum current capacity: 24A/contact.
3,5,6	-V	Negative output voltage. Maximum current capacity: 24A/contact.
7	On/Off control	Turns the output to On and Off by electrical signal or dry contact between pin 7
		and pin 10 (Signal Return). 0~0.6V or Short: On, 2~15V or Open: Off.
		The maximum source current is 2.6mA.
8	+Sense	Positive sensing. The +Sense signal should be connected to the positive terminal
		of the load. The +Sense and -Sense leads should be twisted pair to minimize noise
		pick-up effect. The maximum load wires drop compensation is 1V/wire.
9	DC_OK	Open collector signal, referenced to pin 10 (Signal Return). On when Vout≥80%+/-
		5% of its rated value. The maximum sink current is 10mA and the maximum
		external voltage is 15V.
10	Signal_Return	Return for the following control and supervisory signals: On/Off, DC_OK,
		Over_temperature Alarm, AC_Fail, Auxiliary 12V supply. The Signal return is isolated
		from the output terminals.
11	AC_Fail	Open collector signal, referenced to pin 10 (Signal Return). On when the input
		voltage is ≥85Vrms. The maximum sink current is 10mA and the maximum external
		voltage is15Vdc.
12	Over	Open collector signal, referenced to pin 10 (Signal Return). On when the internal
	Temperature	temperature is within safe limit, Off approx. 10°C below Thermal shut down. The
	Alarm	maximum sink current is 10mA and the maximum external voltage is 15V.
13	-Sense	Negative sensing. The -S signal should be connected to the negative terminal of
		the load. The -S and +S leads should be twisted pair to minimize noise pick-up
		effect. The maximum load wires drop compensation is 1V/wire.
14	V_Trim	Connection for output voltage trimming. The voltage can be trimmed within its
		range specifications.
15	CS	Current sharing signal. When units are connected in parallel, the CS pins of the
		units should be connected to allow current balance between units.
16	+12V Auxiliary	Auxiliary voltage output, 11.2~12.5V, referenced to pin 10 (Signal Return). The
		maximum load current is 0.25A. This output has built in Oring diode and is not
		controlled by the On/Off control.
17	SDA	Serial Data used in the I2C interface option. Refer to the I2C interface description.
18	SCL	Serial Clock used in the I2C interface option. Refer to the I2C interface description.
19,20,21	A0, A1, A2	I2C interface address lines. Refer to the I2C interface description in Chapter 7.
22	ACG	AC Ground connection, refer to the safety instructions for safety standards requirements.
		For "/P" models the AC Ground is connected via the front panel IEC inlet.
23	AC Line	AC Line connection, refer to the safety instructions for safety standards requirements.
		For "/P" models the AC Line is connected via the front panel IEC inlet.
24	AC Neutral	AC Neutral connection, refer to the safety instructions for safety standards requirements.
		For "/P" models the AC Neutral is connected via the front panel IEC inlet.

Table 3-4: Rear In/Out connector pins function description

3.7.8 REPACKAGING FOR SHIPMENT

The original packaging material is reusable. If the original package is not available, contact the Lambda Sales or service facility near you for details on obtaining suitable packaging and shipping information. To ensure safe transportation of the instrument, it is recommended to use the original package.

Please attach a tag to the power supply describing the problem and specifying the owner, model number and serial number of the power supply.

10