Modules location | TOA Electronics FPS1000-48, FPS1000-24, FPS-S1U

17.7.6 Modules location

Up to three FPS1000 modules can be plugged into an FPS-T1U rack.

Refer to Fig 17-2 for the modules location.

PS MODULE “A”

PS MODULE “B”

Air flow direction

Front sidePS MODULE “C” see note 1

Fig 17-2: FPS1000 modules location

Note 1: Forced air cooling allow minimum 50mm of unrestricted air space at the rear of the unit. Do not obsruct air flow to the unit front panel.

17.7.7 Blank panels

Each FPS-T1U rack is supplied with two blank panels in the package. Use the blank panels to close the front panel opening in places where FPS1000 power supplies are not installed. Use M3x6 screws to fix the blank panel to the chassis. Refer to the outline drawings in chapter 18 for details.

17.7.8Repackaging for shipment Refer to Sec. 3.7.8 for details.

44

Image 47

TOA Electronics FPS1000-48, FPS1000-24, FPS1000-12, FPS1000-32, FPS-S1U, FPS-T1U instruction manual Modules location

Contents

FPS Series 1000W In 1U FPS1000 Series Table of Contents Disclaimer WarrantyLimitation of Warranty Warranty Service FPS1000 Power Supply and FPS-S1U Rack Safety Instructions Safety Symbols FPS1000 Series Specifications Outline Drawings FPS 1000 Series Outline Drawings FPS 1000/P Series Outline Drawings FPS1000 Power Supply Installation Current Carrying Capacity Connecting the LoadLoad Wiring Making the load connections Noise and Impedance EffectsInductive loads Repackaging for Shipment Input/Output connector information Functions and Features FPS10004.7KΩ Dcok signalACFail signal Remote On/Off control Remote Sensing Basic Connections for Operation Connecting single load, Local sensingConnecting Single Load, Remote Sensing Connecting Multiple loads, radial distribution method Grounding outputs Multiple loads connection with distribution terminals Output voltage trimming at parallel operation Parallel and Series OperationParallel operation Parallel operation with Remote sensing Remote On/Off control at parallel operation Signal Return bus at parallel operation Series connection for positive and negative output voltage Series operation I2C BUS Interface Option Eeprom functions Block diagram of the I2C optionOperation and functions 7.4.1. Digital status Output current readback Analog functions4 A/D Scaling FPS1000 Typical application diagram FPS1000 Maintenance FPS-S1U 19 Rack Single Output Maximum output power Chapter FPS-S1U Rack Specifications FPS-S1U Rack Mounting FPS-S1U Rack Installation Rear panel description Control and monitoring signals connector SCL I2C Blank panels Modules location FPS-S1U and FPS-S1U/P Outline Drawings FPS-S1U/P Outline Drawing Multiple loads connection Basic Connections for Operation FPS-S1U Rack Output voltage trimming Supervisory signals12.4 On/Off control Parallel operation with Remote sensing Output voltage trimming at parallel operation Signal Return bus at parallel operation Remote On/Off control at parallel operation Addressing A0, A1, A2 FPS-S1U I2C BUS Interface OptionIntroduction Adjustments and Calibration FPS-S1U MaintenanceUnits under warranty Periodic maintenance FPS-T1U 19 Rack Triple Output Chapter FPS-T1U Rack Specifications FPS-T1U Rack Mounting FPS-T1U Rack Installation FPS-T1U Rear panel J1A, J2B, J3C Conector Description Modules location FPS-T1U and FPS-T1U/P Outline Drawings FPS-T1U/P Outline Drawing 19.2 On/Off control Basic Connections for Operation FPS-T1U Rack Output Voltag Trimming Load Series operation Module a Module B Module C FPS-T1U I2C BUS Interface Option FPS-T1U Maintenance