Manuals / Toshiba / Computer Equipment / Printer

Toshiba B-850 owner manual EO1-33029C

Models: B-850

1 116

Download 116 pages 33.05 Kb

Troubleshooting Specifications Install Symbols in the message Connecting the Power Cord Dimension Maintenance Possible Problems Operation Reset A4.3 Self-Diagnostic Test

Page 116

E

PRINTED IN JAPAN

EO1-33029C

Page 115 Page 116

Image 116

Toshiba B-850 owner manual EO1-33029C

Page 115 Page 116

Related manuals

Manual 288 pages 53.68 Kb

Our partner
Обсуждение вопроса Возможно ли нарушение, если свет был зелёным? из чата 🇺🇦 Чат серьезных экономистов Мюнхена, Мюнхен, Германия

Related pages Torque Specification Chart for Simplicity 8660EI VCR CODE LIST for JVC LYT0002-048A Installation for Smeg KSE912NX What maintenance tips are available for the Panasonic DP-C354 scanner?

Contents

852-TS12-QQ Energy Star is a U.S. registered mark $51,1 3UHFDXWLRQV Table of Contents On Line Mode Introduction Features UnpackingProduct Overview Accessories Front View Rear View DimensionsAppearance Operation Panel Interior Printer Setup Precautions Procedure before Operation Assembling the Accessories Assembling the Supply Holder Frame Connecting the Cables to Your Printer Connecting the Power Cord Turning OFF the Printer Turning the PrinterTurning on the Printer Installing the Media onto the Supply Holder Unit Disassembling the Supply Holder Unit Installing the Media and reassembling the Supply Holder Unit Loading Media into the Printer Print Head Block Element Release Lever Printer Down Setting the Black Mark Sensor Setting Sensor PositionsSetting the Feed Gap Sensor Loading the Ribbon Inserting the Optional Pcmcia Cards COM Test Print At the same time Test Print Printer Operation Overview Operating Modes Operating Modes Installing the Printer Drivers System RequirementsDriver Download System EO1-33029 Installing the Printer Drivers Driver Download Driver Installation Cont Driver Installation Add Printers Add Printers Uninstalling the TEC B-852 Printer Driver Using the B-852 Printer Properties Menus Printer Operation General Properties Tab Details Tab Print to the following Transmission Retry ∙ In Print to the following port, click the port just mapped Regional Settings Tab Regional Settings Tab Setup Tab Portrait Landscape Rotated Additional Advanced Options Graphics Tab Bar Fonts Tab Printer Operation Bar Fonts Tab Cont. Bar Code Options Stock Tab Stock Tab Sensor Select Stock Tab Options Tab Options tab, the following display screen will appear Testing Tab Testing Tab Testing Tab Testing Tab About Tab About Tab On Line Mode Operation Panel Operation Reset Dump Mode Print Head/Platen/ Sensors MaintenanceCleaning Care/Handling of the Media and Ribbon Troubleshooting Error MessagesError Messages Problems/Causes Solutions Restart key Possible Problems Causes Solutions Possible ProblemsError Messages Problems/Cause Solutions Removing Jammed Media Feed key Threshold Setting„Threshold setting procedure Model 852-TS12-QQ Appendix 1 SpecificationsA1.1 Printer A1.2 Options A1.3 MediaA1.3.1 Media Type Label A1.3.2 Detection Area of the Transmissive Sensor A1.3.3 Detection Area of the Reflective Sensor A1.3.4 Effective Print Area A1.4 Ribbon Symbols in the message Appendix 2 Messages and Leds Following message appears Appendix 3 Interface „Interface Cables Appendix 4 System Mode A4.1 Operation Panel If the power is turn on while A4.2 Overview Maintenance counter/parameter settings print out A4.3 Self-Diagnostic TestPrinting mode selection Self-Diagnostic Test and the result print out Print head element check A4.4 Printer Parameter Fine Adjustment Feed Length Fine Adjustment Restart Feed Cut Position Fine Adjustment Back Feed Length Fine Adjustment Axis Fine Adjustment Thermal Transfer Print Thermal Direct Print Ribbon Motor Voltage Fine Adjustment Feed/Rewind Motor Rewind Motor Feed Motor A4.4 Printer Parameter Fine Adjustment Cont Threshold Manual Fine Adjustment Black Mark/Feed Gap SensorBlack Mark Sensor Feed Gap Sensor Test Pattern Selection Print Condition SettingA4.5 Test Print Issue Count Setting Specifying the Print Condition for the Test Print Sensor Type Selection Print Speed SettingPrinting Mode Selection Paper Feed Selection Issue Mode SelectionLabel Length Setting Test Print Pattern Selection Pause keySlant Line 1 dot Slant Line 3 dots Characters BarcodeNon-Printing Factory Test A4.6 PCL Emulation Setting Auto Print Sensor Type Selection Emulation ON/OFF SelectionPrint Speed Media Size Selection Issue Mode SelectionMedia Width Setting Media Length Setting A4.7.1 Self-Diagnostic Test Result Sample and Descriptions A4.7 Additional Information Sdram 8MB SENSOR1 0 0 0 0 0 0 0 0 1 0 0 1 EXP.I/O OK Total Feed ∙ Descriptions of the Maintenance Counter ODD ODD A4.7.3 Magnified Views of Slant Line Pattern Letter Appendix 5 Print Samples CODE39 Full Ascii UPC-E+2 digits UPC-E+5 digits EAN8+2 digits EAN8+5 digits UPC-A+2 digits UPC-A+5 digits KIX Code MaxiCode Glossaries Bar code Pre-printed media Index Index Page Page EO1-33029C

Top Page Image Contents