APPENDIX 1 SPECIFICATIONS |
A1.3 Media
A1.3.1 Media Type (Cont.)
|
|
|
| [Unit: mm] |
| Label dispensing mode | Batch mode |
| Cut mode |
Item |
| |||
|
|
| ||
cMinimum media pitch | 15.0 |
| Label: 38.0 | |
| Tag: 25.4 | |||
d |
|
| ||
eLabel length | Min. 12.5 |
| Min. 32.0 | |
fWidth including backing paper | 100.0- 242.0 |
| 100.0 – 235.0 | |
gGap length | 2.5 – 20.0 |
| 6.0 – 20.0 | |
hBlack mark length (Tag paper) |
| 2.0 – 10.0 | ||
iEffective print width |
| 216.8±0.2 | ||
jPrint speed up/slow down area |
| 1.0 | ||
Black mark length (Label) | 2.0 – 20.0 |
| 6.0 – 20.0 | |
Max. print length |
| 640.0 | ||
Maximum effective length for on the fly issue |
| 320.0 | ||
Max. outer roll diameter |
| φ230 | ||
Thickness | Label + backing paper |
| 0.13 – 0.18 | |
Tag |
| 0.08 – 0.18 | ||
|
| |||
NOTES:
1.To ensure print quality and print head life use only TOSHIBA TEC specified media.
2.When using the cutter ensure that label length dplus
3.When requesting black marks on label rolls, the following requirements must be satisfied. When the gap length is less than 4 mm:
The black mark length should be longer than the gap length. When the gap length is 4 mm or more:
The black mark should not overlap the gap for more than 4 mm or the following label.
Black marks should be printed on reverse side of the gaps. Also, they should contact or overlap the preceding label’s bottom end line.
4.“On the fly issue” means that the printer can feed and print without stopping between labels.
A1.3.2 Detection Area of the Transmissive Sensor
The transmissive sensor is movable from the center to the left edge of media.
The transmissive sensor detects a gap between labels, as illustrated below.
|
|
|
|
|
| Area to be detected. |
|
|
| Center of media | |||||||||||||||||
Sensor position |
|
|
|
|
|
|
|
|
|
| Print side | ||||||||||||||||
|
|
|
| ||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Min. 2.0 mm |
|
|
|
|
|
|
|
|
|
| Label |
|
|
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
| Gap |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
(Min. 6.0 mm when using |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
the cutter module.) |
|
|
|
|
|
|
|
|
|
| Label |
|
|
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||
|
|
| Min. 12 mm |
|
|
|
|
|
|
|
|
|
|
| Media feed direction | ||||||||||||
|
|
|
|
|
| ||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||
|
|
|
|
|
|
|
|
|
|
|
| Sensor is movable |
|
|
|
| |||||||||||
|
|
|
|
|
|
|
|
|
|
|
| within this range. |
|
|
|
| |||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
A1- 3
