Toshiba B-850 manual

3. PRINTER OPERATION

EO1-33029

3.3 Installing the Printer Drivers

3.3.4 Add Printers (Cont.)

3.3.5Uninstalling the TEC B-852 Printer Driver

NOTE:

Do not uninstall the printer until you have closed all applications.

CAUTION!

If you are going to install an upgraded version of the TEC printer driver you must first uninstall the folder “TOSHIBA TEC PRINTER DRIVER MONO” by the steps outlined here.

4.After the TEC Printer Driver has been successfully loaded, the Printers screen should appear as shown below, showing the TEC B- 852 as being successfully installed.

If it becomes necessary to remove the TEC B-852 printer driver from your host computer, then it can be removed as follows.

1.In the Printers screen shown above, click on the TEC B-852icon to highlight it.

2.Click on the File menu, and when the File sub menu appears, click on Delete. The icon for the TEC B-852 will disappear from the Printers screen.

3.Access the Windows Control Panel and click on the Add/Remove Programs icon.

4.The Add/Remove Program Properties window will appear. In this window, click on TOSHIBA TEC PRINTER DRIVER MONO to highlight it and then click on the Add/Remove button.

5.In the Confirm File Deletion screen that appears, click on the Yes button to complete the removal of the TEC Printer Driver.

3- 8

Image 35

Toshiba B-850 owner manual Add Printers Uninstalling the TEC B-852 Printer Driver

Contents

852-TS12-QQ Energy Star is a U.S. registered mark $51,1 3UHFDXWLRQV Table of Contents On Line Mode Introduction Features UnpackingProduct Overview Accessories Front View Rear View DimensionsAppearance Interior Operation Panel Precautions Printer Setup Procedure before Operation Assembling the Supply Holder Frame Assembling the Accessories Connecting the Cables to Your Printer Connecting the Power Cord Turning OFF the Printer Turning the PrinterTurning on the Printer Disassembling the Supply Holder Unit Installing the Media onto the Supply Holder Unit Installing the Media and reassembling the Supply Holder Unit Loading Media into the Printer Print Head Block Element Release Lever Down Printer Setting the Black Mark Sensor Setting Sensor PositionsSetting the Feed Gap Sensor Loading the Ribbon COM Inserting the Optional Pcmcia Cards Test Print At the same time Test Print Overview Operating Modes Printer Operation Operating Modes System Installing the Printer DriversSystem Requirements Driver Download EO1-33029 Installing the Printer Drivers Driver Download Driver Installation Cont Driver Installation Add Printers Add Printers Uninstalling the TEC B-852 Printer Driver Using the B-852 Printer Properties Menus Printer Operation General Properties Tab Print to the following Details Tab Transmission Retry ∙ In Print to the following port, click the port just mapped Regional Settings Tab Regional Settings Tab Setup Tab Portrait Landscape Rotated Additional Advanced Options Graphics Tab Bar Fonts Tab Printer Operation Bar Fonts Tab Cont. Bar Code Options Stock Tab Stock Tab Sensor Select Stock Tab Options tab, the following display screen will appear Options Tab Testing Tab Testing Tab Testing Tab Testing Tab About Tab About Tab Operation Panel On Line Mode Dump Mode Operation Reset Print Head/Platen/ Sensors MaintenanceCleaning Care/Handling of the Media and Ribbon Restart key TroubleshootingError Messages Error Messages Problems/Causes Solutions Possible Problems Causes Solutions Possible ProblemsError Messages Problems/Cause Solutions Removing Jammed Media Feed key Threshold Setting„Threshold setting procedure Model 852-TS12-QQ Appendix 1 SpecificationsA1.1 Printer Label A1.2 OptionsA1.3 Media A1.3.1 Media Type A1.3.2 Detection Area of the Transmissive Sensor A1.3.4 Effective Print Area A1.3.3 Detection Area of the Reflective Sensor A1.4 Ribbon Appendix 2 Messages and Leds Symbols in the message Following message appears „Interface Cables Appendix 3 Interface A4.1 Operation Panel Appendix 4 System Mode A4.2 Overview If the power is turn on while Maintenance counter/parameter settings print out A4.3 Self-Diagnostic TestPrinting mode selection Print head element check Self-Diagnostic Test and the result print out A4.4 Printer Parameter Fine Adjustment Restart Feed Feed Length Fine Adjustment Cut Position Fine Adjustment Back Feed Length Fine Adjustment Axis Fine Adjustment Thermal Transfer Print Thermal Direct Print Rewind Motor Feed Motor Ribbon Motor Voltage Fine Adjustment Feed/Rewind Motor Feed Gap Sensor A4.4 Printer Parameter Fine Adjustment ContThreshold Manual Fine Adjustment Black Mark/Feed Gap Sensor Black Mark Sensor Test Pattern Selection Print Condition SettingA4.5 Test Print Specifying the Print Condition for the Test Print Issue Count Setting Sensor Type Selection Print Speed SettingPrinting Mode Selection Paper Feed Selection Issue Mode SelectionLabel Length Setting Slant Line 3 dots Test Print Pattern SelectionPause key Slant Line 1 dot Factory Test CharactersBarcode Non-Printing Auto Print A4.6 PCL Emulation Setting Sensor Type Selection Emulation ON/OFF SelectionPrint Speed Media Size Selection Issue Mode SelectionMedia Width Setting Media Length Setting A4.7 Additional Information A4.7.1 Self-Diagnostic Test Result Sample and Descriptions Sdram 8MB SENSOR1 0 0 0 0 0 0 0 0 1 0 0 1 EXP.I/O OK Total Feed ∙ Descriptions of the Maintenance Counter ODD ODD Letter A4.7.3 Magnified Views of Slant Line Pattern Appendix 5 Print Samples UPC-E+2 digits UPC-E+5 digits EAN8+2 digits EAN8+5 digits CODE39 Full Ascii KIX Code MaxiCode UPC-A+2 digits UPC-A+5 digits Bar code Glossaries Pre-printed media Index Index Page Page EO1-33029C