Connecting the Power Cord | Toshiba B-852 specification

2. PRINTER SETUP

ENGLISH VERSION EO1-33055

2.3 Connecting the Power Cord

2.3Connecting the Power Cord

CAUTION!

1.Make sure that the printer power switch is turned to the off position before connecting the power cord to prevent possible electric shock or damage to the printer.

2.Use only the power cord supplied with the printer. Use of any other cord may cause electric shock or fire.

3.Connect the power cord to a three-prong outlet only, with the third prong being a good ground (earth) connection.

1.Make sure that the printer power switch is in the off position.

Power Switch

2.Connect the Power Cord to the printer as shown in the figure below.

Power Connector

3.Plug the other end of the Power Cord into a grounded outlet as shown in the figure below.

Power Cord	Power Cord

[Example of US Type(QQ model)]

[Example of EU Type(QP model)]

E2- 4

Image 17

Toshiba B-852 owner manual Connecting the Power Cord

Contents

Series Vorsicht CE Compliance for EU only Series Waste Recycling information for users Meanings of Each Symbol Safety Summary Request Regarding Maintenance Precautions Table of Contents E4-1 E3-1E5-1 EA1-1 Unpacking Introduction FeaturesProduct Overview Accessories Front View Rear View DimensionsAppearance Interior Operation Panel Option Name Type Description Options Setup Flow Printer SetupProcedure Manual threshold setting Installation Assembling the Supply Holder Frame Assembling the Accessories Connecting the Power Cord Loading the Media Installing the Media onto the Supply Holder UnitStraight and true through the printer Disassembling the Supply Holder Unit Spacer Supply Holder Loading Media into the Printer Print Head Element Head Block Release Lever Down Setting the Black Mark Sensor Setting Sensor PositionsSetting the Feed Gap Sensor Loading the Ribbon Connecting the Cables to Your Printer Turning on the Printer Turning the Printer Environment How to enter the System Mode While 2PARAMETER SET is displayed on the LCD Message Parameter SettingTime the Pause key is pressed, the sub menus are displayed Sequentially Character Code Selection Character Zero SelectionUse the Feed or Restart key to select a desired option After selecting a character code, press the Pause key After selecting a baud rate, press the Pause key Baud Rate SelectionData Length Selection After selecting a data length, press the Pause key Flow Control Code Selection Stop Bit Length SelectionParity Selection After selecting a language, press the Pause key LCD Language SelectionAuto Forward Wait Selection After selecting an auto forward wait, press the Pause key Feed key Control Code Selection After selecting the Feed key function, press the Pause key Feed Key Function Selection After selecting a Kanji code, press the Pause key Kanji Code SelectionEuro Code Selection After selecting a Euro code, press the Pause key After selecting auto print head check, press the Pause key Auto Print Head Check SelectionCentronics Interface ACK/BUSY Timing Selection After selecting an ACK/BUSY timing, press the Pause key After selecting the Input Prime, press the Pause key Web Printer Function SelectionInput Prime Selection After selecting a Plug & Play, press the Pause key Expansion I/O Interface Type SelectionPlug & Play Selection After selecting a Label End type, press the Pause key Maxi Code Specification SelectionLabel End/Ribbon End Selection After selecting the receive buffer, press the Pause key Dump Mode SettingUse the Feed or Restart key to select a printing method After selecting a printing method, press the Pause key Required Label Length Data in the receive buffer is printed as followsReceive Buffer Size When the Pause key is pressed, Basic program is executed Basic Expansion Mode Not activated Activated Feed gap sensor Black mark sensor LAN Setting Time Setting Date Setting Cont Real Time Clock Setting 3 Low Battery Check SettingRTC Data Renewal Timing Setting IP Address Setting TCP/IP Feed and Pause keys This parameter is to set an IP address Printer IP AddressGateway IP Address This parameter is to set a Gateway IP address Socket Port Subnet MaskThis parameter is to set a Subnet Mask Dhcp This parameter is to enable DhcpDhcp Client ID This parameter is to set a Dhcp client ID Ascii code and Hex. code correspondence table Dhcp Host NameThis parameter is to set a Dhcp host name General Description Installing the Printer DriversIntroduction Parallel Interface Installing the Printer Driver Windows 98/Me E2-43 Windows 2000/XP E2-45 USB Interface E2-47 E2-48 E2-49 Finish button E2-51 E2-52 E2-53 Uninstalling the Printer Driver Adding a LAN Port Windows 98/ME Adding/Deleting a LAN Port Deleting a LAN Port Others Printer Driver Upgrades Using the Printer Driver Print Test Adjustment When using an optional Cutter Module Feed Amount Fine Adjustment Position and Print Tone Fine AdjustmentCoordinate Fine Adjustment Threshold Fine Adjustment Feed gap sensor When setting +0.0 mm After selecting a fine adjustment value, press the Pause key Position and Print Tone Fine Adjustment Restart Feed When setting +50.0 mm When setting -50.0 mm Print Tone Fine Adjustment Ribbon Motor Voltage Fine Adjustment Jam errors Threshold SettingSelect the sensor to be adjusted by using the Feed key Manually set Lower Black Mark Sensor Adjustment Upper Black Mark Sensor AdjustmentFeed Gap Sensor Adjustment Lower Black Mark Sensor/Feed Gap Sensor Adjustment No media „ When using the Feed Gap Sensor „ When using the Black Mark Sensor Press and hold the Restart or Feed key for about 3 seconds „ Manual Threshold Setting„ Storing a No Media Level Voltage Feed Gap Sensor Operation Panel On Line ModeUsed to stop printing temporarily Used to restart printing Press and hold the Restart key for 3 seconds or longer Operation Reset Print Head/Platen/ Sensors MaintenanceCleaning Optional Cutter Module Covers and Panels Error Messages TroubleshootingError Messages Problems/Causes Solutions Restart key Error Messages Problems/CauseMedia has run out Possible Problems Causes Possible Problems Attach the Cutter Cover properly Remove the jammed paper Clean the Cutter BladeLoad the ribbon properly Removing Jammed Media Model 852-TS22-QQ-R 852-TS22-QP-R Printer SpecificationsThis section describes the printer specifications Mail 4STATE Customer CODE, RSS14 Media Supply SpecificationsMedia Type Label Detection Area of the Reflective Sensor Detection Area of the Transmissive Sensor Figure below shows the effective print area on the media Effective Print Area Media type Description RibbonRecommended Media and Ribbon Types Ribbon type Description Care/Handling of the Media and RibbonCombination of Media and Ribbon Media type Vellum paper and label Appendix 1 Messages and Leds Symbols in the message Analyzing the command Command error has occurred100BASE LAN is being initialised Dhcp Client is being initialised Following message appears Parallel interface Centronics Appendix 2 Interface Connector Number of ports Connector RJ-45 Number of ports Power source Self power Connector Type BStandard LED status Link LED Serial interface Option B-SA704-RS-QM-R Wireless LAN Option B-SA704-WLAN-QM-R Expansion I/O Interface Option B-SA704-IO-QM-R Appendix 3 Print Samples NW7 JAN13, EAN13 UPC-E EAN13+2 digits EAN13+5 digits JAN8, EAN8 MSI Interleaved 2CODE39 Full Ascii UPC-E+2 digits UPC-E+5 digits EAN8+2 digits EAN8+5 digits UPC-A+5 digits UPC-A+2 digitsIndustrial 2 Data Matrix Customer bar code of high priority QR code Appendix 4 Glossaries Media and ribbon See Black mark sensorSee Feed gap sensor USB Universal Serial Bus 3-1, A1-1 Index Index EO1-33055D