Installation | Toshiba B-852 manual

2. PRINTER SETUP

ENGLISH VERSION EO1-33055

2.1 Installation

2.1 Installation

To insure the best operating environment, and to assure the safety of the operator and the equipment, please observe the following precautions.

•Operate the printer on a stable, level, operating surface in a location free from excessive humidity, high temperature, dust, vibration or direct sunlight.

•Keep your work environment static free. Static discharge can cause damage to delicate internal components.

•Make sure that the printer is connected to a clean source of AC Power and that no other high voltage devices that may cause line noise interference are connected to the same mains.

•Assure that the printer is connected to the AC mains with a three- prong power cable that has the proper ground (earth) connection.

•Do not operate the printer with the cover open. Be careful not to allow fingers or articles of clothing to get caught into any of the moving parts of the printer especially the optional cutter mechanism.

•Make sure to turn off the printer power and to remove the power cord from the printer whenever working on the inside of the printer such as changing the ribbon or loading the media, or when cleaning the printer.

•For best results, and longer printer life, use only TOSHIBA TEC recommended media and ribbons.

•Store the media and ribbons in accordance with their specifications.

•This printer mechanism contains high voltage components; therefore you should never remove any of the covers of the machine as you may receive an electrical shock. Additionally, the printer contains many delicate components that may be damaged if accessed by unauthorised personnel.

•Clean the outside of the printer with a clean dry cloth or a clean cloth slightly dampened with a mild detergent solution.

•Use caution when cleaning the thermal print head as it may become very hot while printing. Wait until it has had time to cool before cleaning. Use only the TOSHIBA TEC recommended print head cleaner to clean the print head.

•Do not turn off the printer power or remove the power plug while the printer is printing or while the ON LINE lamp is blinking.

E2- 2

Image 15

Toshiba B-852 owner manual Installation

Contents

Series Vorsicht CE Compliance for EU only Series Waste Recycling information for users Meanings of Each Symbol Safety Summary Request Regarding Maintenance Precautions Table of Contents EA1-1 E3-1E4-1 E5-1 Introduction Features Product OverviewUnpacking Accessories Dimensions AppearanceFront View Rear View Interior Operation Panel Option Name Type Description Options Manual threshold setting Printer SetupSetup Flow Procedure Installation Assembling the Supply Holder Frame Assembling the Accessories Connecting the Power Cord Disassembling the Supply Holder Unit Installing the Media onto the Supply Holder UnitLoading the Media Straight and true through the printer Spacer Supply Holder Loading Media into the Printer Print Head Element Head Block Release Lever Down Setting Sensor Positions Setting the Feed Gap SensorSetting the Black Mark Sensor Loading the Ribbon Connecting the Cables to Your Printer Turning on the Printer Turning the Printer Environment How to enter the System Mode Sequentially Parameter SettingWhile 2PARAMETER SET is displayed on the LCD Message Time the Pause key is pressed, the sub menus are displayed After selecting a character code, press the Pause key Character Zero SelectionCharacter Code Selection Use the Feed or Restart key to select a desired option After selecting a data length, press the Pause key Baud Rate SelectionAfter selecting a baud rate, press the Pause key Data Length Selection Stop Bit Length Selection Parity SelectionFlow Control Code Selection After selecting an auto forward wait, press the Pause key LCD Language SelectionAfter selecting a language, press the Pause key Auto Forward Wait Selection Feed key Control Code Selection After selecting the Feed key function, press the Pause key Feed Key Function Selection After selecting a Euro code, press the Pause key Kanji Code SelectionAfter selecting a Kanji code, press the Pause key Euro Code Selection After selecting an ACK/BUSY timing, press the Pause key Auto Print Head Check SelectionAfter selecting auto print head check, press the Pause key Centronics Interface ACK/BUSY Timing Selection Web Printer Function Selection Input Prime SelectionAfter selecting the Input Prime, press the Pause key Expansion I/O Interface Type Selection Plug & Play SelectionAfter selecting a Plug & Play, press the Pause key Maxi Code Specification Selection Label End/Ribbon End SelectionAfter selecting a Label End type, press the Pause key After selecting a printing method, press the Pause key Dump Mode SettingAfter selecting the receive buffer, press the Pause key Use the Feed or Restart key to select a printing method Data in the receive buffer is printed as follows Receive Buffer SizeRequired Label Length When the Pause key is pressed, Basic program is executed Basic Expansion Mode Not activated Activated Feed gap sensor Black mark sensor LAN Setting Time Setting Date Setting Real Time Clock Setting 3 Low Battery Check Setting RTC Data Renewal Timing SettingCont IP Address Setting TCP/IP Feed and Pause keys This parameter is to set a Gateway IP address Printer IP AddressThis parameter is to set an IP address Gateway IP Address Subnet Mask This parameter is to set a Subnet MaskSocket Port This parameter is to set a Dhcp client ID This parameter is to enable DhcpDhcp Dhcp Client ID Dhcp Host Name This parameter is to set a Dhcp host nameAscii code and Hex. code correspondence table Installing the Printer Drivers IntroductionGeneral Description Parallel Interface Installing the Printer Driver Windows 98/Me E2-43 Windows 2000/XP E2-45 USB Interface E2-47 E2-48 E2-49 Finish button E2-51 E2-52 E2-53 Uninstalling the Printer Driver Adding a LAN Port Windows 98/ME Adding/Deleting a LAN Port Deleting a LAN Port Others Printer Driver Upgrades Using the Printer Driver Print Test Adjustment When using an optional Cutter Module Threshold Fine Adjustment Feed gap sensor Position and Print Tone Fine AdjustmentFeed Amount Fine Adjustment Coordinate Fine Adjustment When setting +0.0 mm After selecting a fine adjustment value, press the Pause key Position and Print Tone Fine Adjustment Restart Feed When setting +50.0 mm When setting -50.0 mm Print Tone Fine Adjustment Ribbon Motor Voltage Fine Adjustment Manually set Threshold SettingJam errors Select the sensor to be adjusted by using the Feed key Lower Black Mark Sensor/Feed Gap Sensor Adjustment No media Upper Black Mark Sensor AdjustmentLower Black Mark Sensor Adjustment Feed Gap Sensor Adjustment „ When using the Feed Gap Sensor „ When using the Black Mark Sensor „ Manual Threshold Setting „ Storing a No Media Level VoltagePress and hold the Restart or Feed key for about 3 seconds Feed Gap Sensor Used to restart printing On Line ModeOperation Panel Used to stop printing temporarily Press and hold the Restart key for 3 seconds or longer Operation Reset Maintenance CleaningPrint Head/Platen/ Sensors Optional Cutter Module Covers and Panels Solutions TroubleshootingError Messages Error Messages Problems/Causes Error Messages Problems/Cause Media has run outRestart key Possible Problems Causes Possible Problems Clean the Cutter Blade Load the ribbon properlyAttach the Cutter Cover properly Remove the jammed paper Removing Jammed Media Printer Specifications This section describes the printer specificationsModel 852-TS22-QQ-R 852-TS22-QP-R Mail 4STATE Customer CODE, RSS14 Label Supply SpecificationsMedia Media Type Detection Area of the Reflective Sensor Detection Area of the Transmissive Sensor Figure below shows the effective print area on the media Effective Print Area Ribbon Recommended Media and Ribbon TypesMedia type Description Media type Vellum paper and label Care/Handling of the Media and RibbonRibbon type Description Combination of Media and Ribbon Appendix 1 Messages and Leds Symbols in the message Dhcp Client is being initialised Command error has occurredAnalyzing the command 100BASE LAN is being initialised Following message appears Parallel interface Centronics Appendix 2 Interface Connector LED status Link LED Number of ports Power source Self power Connector Type BNumber of ports Connector RJ-45 Standard Serial interface Option B-SA704-RS-QM-R Wireless LAN Option B-SA704-WLAN-QM-R Expansion I/O Interface Option B-SA704-IO-QM-R Appendix 3 Print Samples UPC-E+2 digits UPC-E+5 digits EAN8+2 digits EAN8+5 digits JAN8, EAN8 MSI Interleaved 2NW7 JAN13, EAN13 UPC-E EAN13+2 digits EAN13+5 digits CODE39 Full Ascii Customer bar code of high priority QR code UPC-A+2 digitsUPC-A+5 digits Industrial 2 Data Matrix Appendix 4 Glossaries USB Universal Serial Bus See Black mark sensorMedia and ribbon See Feed gap sensor 3-1, A1-1 Index Index EO1-33055D