2. PRINTER SETUP

ENGLISH VERSION EO1-33055

2.9 Setting an Operating Environment

2.9.7IP Address Setting (TCP/IP) (Cont.)

NOTE:

Pressing the [PAUSE] key while “DHCP ON” is displayed allows you to set a DHCP client ID.

(5) DHCP

This parameter is to enable DHCP.

DHCP

 

[PAUSE]

[RESTART] or [FEED]

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DHCP OFF

 

 

 

 

DHCP ON

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

[PAUSE]

DHCP CLIENT ID

NOTES:

1.Code used to enter a DHCP client ID is selectable between ASCII code (alphanumeric) and Hex code.

2.Set a character or value for each byte by using the

[RESTART] or [FEED] key.

[RESTART] key: Increment

[FEED] key: Decrement

3.Press the [PAUSE] key to enter the next byte. Repeat this until 16th byte is entered.

4.A DHCP ID can be used to check what IP address is assigned to which client on a DHCP server. If a DHCP ID is not assigned, MAC address of a network device (LAN card or LAN interface board) will be notified to the server as a DHCP ID instead.

A DHCP ID is a 16-byte character string. As “FFH” (hex. code) is recognized as a terminator, if the top byte of DHCP ID is “FFH”, it is considered that a DHCP ID is not assigned.

(6) DHCP Client ID

This parameter is to set a DHCP client ID.

DHCP CLIENT ID

[PAUSE]

[FEED] or [RESTART]

 

 

 

<7>IP ADDRESS

 

 

 

MODE ASCII

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ASCII Code

 

 

 

 

 

 

 

 

 

 

 

 

Hex. Code

[PAUSE]

 

 

 

 

 

[PAUSE]

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ABCDEFGHIJKLMNOP

 

 

 

4142434445464748

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Enter a character or a value for each of 1st byte to 16th

 

 

 

 

 

byte sequentially using the [FEED] or [RESTART] key.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

[PAUSE]

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

[PAUSE]

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

E2-38

Page 51
Image 51
Toshiba B-852 owner manual This parameter is to enable Dhcp, Dhcp Client ID, This parameter is to set a Dhcp client ID