USB Interface | Toshiba B-852 guide

2. PRINTER SETUP

ENGLISH VERSION EO1-33055

2.10 Installing the Printer Drivers

(2)USB INTERFACE

Installation starts by the operating system’s plug-and-play function.

Windows 98/Me

(1)Turn the printer ON, then connect it to your host computer with the USB cable.

The “New Hardware Found” dialog box is displayed, and “USB Device” is detected.

(2)After a while, the “Add New Hardware Wizard” dialog box is displayed.

Select “Specify the location of the driver (Advanced)”, then click on the [Next] button.

E2-46

Image 59

Toshiba B-852 owner manual USB Interface

Contents

Series Vorsicht CE Compliance for EU only Series Waste Recycling information for users Meanings of Each Symbol Safety Summary Request Regarding Maintenance Precautions Table of Contents EA1-1 E3-1E4-1 E5-1 Unpacking Introduction FeaturesProduct Overview Accessories Front View Rear View DimensionsAppearance Interior Operation Panel Option Name Type Description Options Manual threshold setting Printer SetupSetup Flow Procedure Installation Assembling the Supply Holder Frame Assembling the Accessories Connecting the Power Cord Disassembling the Supply Holder Unit Installing the Media onto the Supply Holder UnitLoading the Media Straight and true through the printer Spacer Supply Holder Loading Media into the Printer Print Head Element Head Block Release Lever Down Setting the Black Mark Sensor Setting Sensor PositionsSetting the Feed Gap Sensor Loading the Ribbon Connecting the Cables to Your Printer Turning on the Printer Turning the Printer Environment How to enter the System Mode Sequentially Parameter SettingWhile 2PARAMETER SET is displayed on the LCD Message Time the Pause key is pressed, the sub menus are displayed After selecting a character code, press the Pause key Character Zero SelectionCharacter Code Selection Use the Feed or Restart key to select a desired option After selecting a data length, press the Pause key Baud Rate SelectionAfter selecting a baud rate, press the Pause key Data Length Selection Flow Control Code Selection Stop Bit Length SelectionParity Selection After selecting an auto forward wait, press the Pause key LCD Language SelectionAfter selecting a language, press the Pause key Auto Forward Wait Selection Feed key Control Code Selection After selecting the Feed key function, press the Pause key Feed Key Function Selection After selecting a Euro code, press the Pause key Kanji Code SelectionAfter selecting a Kanji code, press the Pause key Euro Code Selection After selecting an ACK/BUSY timing, press the Pause key Auto Print Head Check SelectionAfter selecting auto print head check, press the Pause key Centronics Interface ACK/BUSY Timing Selection After selecting the Input Prime, press the Pause key Web Printer Function SelectionInput Prime Selection After selecting a Plug & Play, press the Pause key Expansion I/O Interface Type SelectionPlug & Play Selection After selecting a Label End type, press the Pause key Maxi Code Specification SelectionLabel End/Ribbon End Selection After selecting a printing method, press the Pause key Dump Mode SettingAfter selecting the receive buffer, press the Pause key Use the Feed or Restart key to select a printing method Required Label Length Data in the receive buffer is printed as followsReceive Buffer Size When the Pause key is pressed, Basic program is executed Basic Expansion Mode Not activated Activated Feed gap sensor Black mark sensor LAN Setting Time Setting Date Setting Cont Real Time Clock Setting 3 Low Battery Check SettingRTC Data Renewal Timing Setting IP Address Setting TCP/IP Feed and Pause keys This parameter is to set a Gateway IP address Printer IP AddressThis parameter is to set an IP address Gateway IP Address Socket Port Subnet MaskThis parameter is to set a Subnet Mask This parameter is to set a Dhcp client ID This parameter is to enable DhcpDhcp Dhcp Client ID Ascii code and Hex. code correspondence table Dhcp Host NameThis parameter is to set a Dhcp host name General Description Installing the Printer DriversIntroduction Parallel Interface Installing the Printer Driver Windows 98/Me E2-43 Windows 2000/XP E2-45 USB Interface E2-47 E2-48 E2-49 Finish button E2-51 E2-52 E2-53 Uninstalling the Printer Driver Adding a LAN Port Windows 98/ME Adding/Deleting a LAN Port Deleting a LAN Port Others Printer Driver Upgrades Using the Printer Driver Print Test Adjustment When using an optional Cutter Module Threshold Fine Adjustment Feed gap sensor Position and Print Tone Fine AdjustmentFeed Amount Fine Adjustment Coordinate Fine Adjustment When setting +0.0 mm After selecting a fine adjustment value, press the Pause key Position and Print Tone Fine Adjustment Restart Feed When setting +50.0 mm When setting -50.0 mm Print Tone Fine Adjustment Ribbon Motor Voltage Fine Adjustment Manually set Threshold SettingJam errors Select the sensor to be adjusted by using the Feed key Lower Black Mark Sensor/Feed Gap Sensor Adjustment No media Upper Black Mark Sensor AdjustmentLower Black Mark Sensor Adjustment Feed Gap Sensor Adjustment „ When using the Feed Gap Sensor „ When using the Black Mark Sensor Press and hold the Restart or Feed key for about 3 seconds „ Manual Threshold Setting„ Storing a No Media Level Voltage Feed Gap Sensor Used to restart printing On Line ModeOperation Panel Used to stop printing temporarily Press and hold the Restart key for 3 seconds or longer Operation Reset Print Head/Platen/ Sensors MaintenanceCleaning Optional Cutter Module Covers and Panels Solutions TroubleshootingError Messages Error Messages Problems/Causes Restart key Error Messages Problems/CauseMedia has run out Possible Problems Causes Possible Problems Attach the Cutter Cover properly Remove the jammed paper Clean the Cutter BladeLoad the ribbon properly Removing Jammed Media Model 852-TS22-QQ-R 852-TS22-QP-R Printer SpecificationsThis section describes the printer specifications Mail 4STATE Customer CODE, RSS14 Label Supply SpecificationsMedia Media Type Detection Area of the Reflective Sensor Detection Area of the Transmissive Sensor Figure below shows the effective print area on the media Effective Print Area Media type Description RibbonRecommended Media and Ribbon Types Media type Vellum paper and label Care/Handling of the Media and RibbonRibbon type Description Combination of Media and Ribbon Appendix 1 Messages and Leds Symbols in the message Dhcp Client is being initialised Command error has occurredAnalyzing the command 100BASE LAN is being initialised Following message appears Parallel interface Centronics Appendix 2 Interface Connector LED status Link LED Number of ports Power source Self power Connector Type BNumber of ports Connector RJ-45 Standard Serial interface Option B-SA704-RS-QM-R Wireless LAN Option B-SA704-WLAN-QM-R Expansion I/O Interface Option B-SA704-IO-QM-R Appendix 3 Print Samples UPC-E+2 digits UPC-E+5 digits EAN8+2 digits EAN8+5 digits JAN8, EAN8 MSI Interleaved 2NW7 JAN13, EAN13 UPC-E EAN13+2 digits EAN13+5 digits CODE39 Full Ascii Customer bar code of high priority QR code UPC-A+2 digitsUPC-A+5 digits Industrial 2 Data Matrix Appendix 4 Glossaries USB Universal Serial Bus See Black mark sensorMedia and ribbon See Feed gap sensor 3-1, A1-1 Index Index EO1-33055D