E2-51 | Toshiba B-852 guide

2. PRINTER SETUP

ENGLISH VERSION EO1-33055

2.10 Installing the Printer Drivers

Windows 2000/XP

NOTE:

When plug-and-play printer installation in progress is stopped, be sure to delete the printer detected and displayed on the “Device Manager” tab of the “System Properties” dialog box.

(1)Log on to your host computer as a member who has full control access privilege concerning the printer settings.

(2)Turn the printer ON, then connect it to your host computer with the USB cable.

(3)“USB Device” is automatically detected, and “USB Printing Support” is automatically installed.

(4)After a while, for Windows XP, “TEC B-SA4T” is detected as a new device.

For Windows 2000, “Unknown” device is detected as a new device. In both cases, perform the following steps, though dialog boxes for Windows XP are used.

(5)The “Found New Hardware Wizard” dialog box is displayed. Select “No, not this time”, then click on the [Next] button.

E2-51

Image 64

Toshiba B-852 owner manual E2-51

Contents

Series CE Compliance for EU only Vorsicht Series Waste Recycling information for users Safety Summary Meanings of Each Symbol Precautions Request Regarding Maintenance Table of Contents E3-1 E4-1E5-1 EA1-1 Product Overview Introduction FeaturesUnpacking Accessories Appearance DimensionsFront View Rear View Operation Panel Interior Options Option Name Type Description Printer Setup Setup FlowProcedure Manual threshold setting Installation Assembling the Accessories Assembling the Supply Holder Frame Connecting the Power Cord Installing the Media onto the Supply Holder Unit Loading the MediaStraight and true through the printer Disassembling the Supply Holder Unit Spacer Supply Holder Loading Media into the Printer Print Head Element Head Block Release Lever Down Setting the Feed Gap Sensor Setting Sensor PositionsSetting the Black Mark Sensor Loading the Ribbon Connecting the Cables to Your Printer Turning the Printer Turning on the Printer How to enter the System Mode Environment Parameter Setting While 2PARAMETER SET is displayed on the LCD MessageTime the Pause key is pressed, the sub menus are displayed Sequentially Character Zero Selection Character Code SelectionUse the Feed or Restart key to select a desired option After selecting a character code, press the Pause key Baud Rate Selection After selecting a baud rate, press the Pause keyData Length Selection After selecting a data length, press the Pause key Parity Selection Stop Bit Length SelectionFlow Control Code Selection LCD Language Selection After selecting a language, press the Pause keyAuto Forward Wait Selection After selecting an auto forward wait, press the Pause key Control Code Selection Feed key Feed Key Function Selection After selecting the Feed key function, press the Pause key Kanji Code Selection After selecting a Kanji code, press the Pause keyEuro Code Selection After selecting a Euro code, press the Pause key Auto Print Head Check Selection After selecting auto print head check, press the Pause keyCentronics Interface ACK/BUSY Timing Selection After selecting an ACK/BUSY timing, press the Pause key Input Prime Selection Web Printer Function SelectionAfter selecting the Input Prime, press the Pause key Plug & Play Selection Expansion I/O Interface Type SelectionAfter selecting a Plug & Play, press the Pause key Label End/Ribbon End Selection Maxi Code Specification SelectionAfter selecting a Label End type, press the Pause key Dump Mode Setting After selecting the receive buffer, press the Pause keyUse the Feed or Restart key to select a printing method After selecting a printing method, press the Pause key Receive Buffer Size Data in the receive buffer is printed as followsRequired Label Length Basic Expansion Mode When the Pause key is pressed, Basic program is executed Not activated Activated Feed gap sensor Black mark sensor LAN Setting Date Setting Time Setting RTC Data Renewal Timing Setting Real Time Clock Setting 3 Low Battery Check SettingCont IP Address Setting TCP/IP Feed and Pause keys Printer IP Address This parameter is to set an IP addressGateway IP Address This parameter is to set a Gateway IP address This parameter is to set a Subnet Mask Subnet MaskSocket Port This parameter is to enable Dhcp DhcpDhcp Client ID This parameter is to set a Dhcp client ID This parameter is to set a Dhcp host name Dhcp Host NameAscii code and Hex. code correspondence table Introduction Installing the Printer DriversGeneral Description Installing the Printer Driver Parallel Interface Windows 98/Me E2-43 Windows 2000/XP E2-45 USB Interface E2-47 E2-48 E2-49 Finish button E2-51 E2-52 E2-53 Uninstalling the Printer Driver Adding/Deleting a LAN Port Adding a LAN Port Windows 98/ME Deleting a LAN Port Printer Driver Upgrades Others Using the Printer Driver Adjustment Print Test When using an optional Cutter Module Position and Print Tone Fine Adjustment Feed Amount Fine AdjustmentCoordinate Fine Adjustment Threshold Fine Adjustment Feed gap sensor After selecting a fine adjustment value, press the Pause key When setting +0.0 mm Position and Print Tone Fine Adjustment Restart Feed When setting -50.0 mm When setting +50.0 mm Print Tone Fine Adjustment Ribbon Motor Voltage Fine Adjustment Threshold Setting Jam errorsSelect the sensor to be adjusted by using the Feed key Manually set Upper Black Mark Sensor Adjustment Lower Black Mark Sensor AdjustmentFeed Gap Sensor Adjustment Lower Black Mark Sensor/Feed Gap Sensor Adjustment No media „ When using the Black Mark Sensor „ When using the Feed Gap Sensor „ Storing a No Media Level Voltage „ Manual Threshold SettingPress and hold the Restart or Feed key for about 3 seconds Feed Gap Sensor On Line Mode Operation PanelUsed to stop printing temporarily Used to restart printing Operation Reset Press and hold the Restart key for 3 seconds or longer Cleaning MaintenancePrint Head/Platen/ Sensors Covers and Panels Optional Cutter Module Troubleshooting Error MessagesError Messages Problems/Causes Solutions Media has run out Error Messages Problems/CauseRestart key Possible Problems Possible Problems Causes Load the ribbon properly Clean the Cutter BladeAttach the Cutter Cover properly Remove the jammed paper Removing Jammed Media This section describes the printer specifications Printer SpecificationsModel 852-TS22-QQ-R 852-TS22-QP-R Mail 4STATE Customer CODE, RSS14 Supply Specifications MediaMedia Type Label Detection Area of the Transmissive Sensor Detection Area of the Reflective Sensor Effective Print Area Figure below shows the effective print area on the media Recommended Media and Ribbon Types RibbonMedia type Description Care/Handling of the Media and Ribbon Ribbon type DescriptionCombination of Media and Ribbon Media type Vellum paper and label Symbols in the message Appendix 1 Messages and Leds Command error has occurred Analyzing the command100BASE LAN is being initialised Dhcp Client is being initialised Following message appears Appendix 2 Interface Parallel interface Centronics Connector Number of ports Power source Self power Connector Type B Number of ports Connector RJ-45Standard LED status Link LED Serial interface Option B-SA704-RS-QM-R Wireless LAN Option B-SA704-WLAN-QM-R Expansion I/O Interface Option B-SA704-IO-QM-R Appendix 3 Print Samples JAN8, EAN8 MSI Interleaved 2 NW7 JAN13, EAN13 UPC-E EAN13+2 digits EAN13+5 digitsCODE39 Full Ascii UPC-E+2 digits UPC-E+5 digits EAN8+2 digits EAN8+5 digits UPC-A+2 digits UPC-A+5 digitsIndustrial 2 Data Matrix Customer bar code of high priority QR code Appendix 4 Glossaries See Black mark sensor Media and ribbonSee Feed gap sensor USB Universal Serial Bus Index 3-1, A1-1 Index EO1-33055D