On Line Mode, Operation Panel | Toshiba B-852 instruction

3. ON LINE MODE

ENGLISH VERSION EO1-33055

3.1 Operation Panel

3. ON LINE MODE

3.1 Operation Panel

This chapter describes usage and purpose of the keys on the Operation Panel in On Line Mode.

When the printer is in On Line Mode and connected to a host computer, normal operation of printing images on labels or tags can be accomplished.

•The figure below illustrates the Operation Panel and key functions.

POWER LED (Green)

[FEED] key

LCD Message Display

ON LINE LED (Green)

ERROR LED (Red)

[PAUSE] key

[RESTART] key

The LCD Message Display shows messages in alphanumeric characters and symbols to indicate the printer’s status. Up to 16 characters can be displayed on one line.

There are three LED lights on the Operation Panel.

NOTE:

Use the [RESTART] key to resume printing after a pause

LED	Illuminates when…
POWER	The printer is turned on.
ON LINE	The printer is ready to
	print.

ERROR	Any error occurs with
	the printer.

Flashes when…

-----

The printer is communicating with your computer.

-----

condition, or after clearing an error.

There are three keys on the Operation Panel.

PAUSE	Used to stop printing temporarily.
RESTART	Used to restart printing.
FEED	Used to feed the media.

E3- 1

Image 86

Toshiba B-852 owner manual On Line Mode, Operation Panel, Used to stop printing temporarily, Used to restart printing

Contents

Series CE Compliance for EU only Vorsicht Series Waste Recycling information for users Safety Summary Meanings of Each Symbol Precautions Request Regarding Maintenance Table of Contents E5-1 E3-1E4-1 EA1-1 Unpacking Introduction FeaturesProduct Overview Accessories Front View Rear View DimensionsAppearance Operation Panel Interior Options Option Name Type Description Procedure Printer SetupSetup Flow Manual threshold setting Installation Assembling the Accessories Assembling the Supply Holder Frame Connecting the Power Cord Straight and true through the printer Installing the Media onto the Supply Holder UnitLoading the Media Disassembling the Supply Holder Unit Spacer Supply Holder Loading Media into the Printer Print Head Element Head Block Release Lever Down Setting the Black Mark Sensor Setting Sensor PositionsSetting the Feed Gap Sensor Loading the Ribbon Connecting the Cables to Your Printer Turning the Printer Turning on the Printer How to enter the System Mode Environment Time the Pause key is pressed, the sub menus are displayed Parameter SettingWhile 2PARAMETER SET is displayed on the LCD Message Sequentially Use the Feed or Restart key to select a desired option Character Zero SelectionCharacter Code Selection After selecting a character code, press the Pause key Data Length Selection Baud Rate SelectionAfter selecting a baud rate, press the Pause key After selecting a data length, press the Pause key Flow Control Code Selection Stop Bit Length SelectionParity Selection Auto Forward Wait Selection LCD Language SelectionAfter selecting a language, press the Pause key After selecting an auto forward wait, press the Pause key Control Code Selection Feed key Feed Key Function Selection After selecting the Feed key function, press the Pause key Euro Code Selection Kanji Code SelectionAfter selecting a Kanji code, press the Pause key After selecting a Euro code, press the Pause key Centronics Interface ACK/BUSY Timing Selection Auto Print Head Check SelectionAfter selecting auto print head check, press the Pause key After selecting an ACK/BUSY timing, press the Pause key After selecting the Input Prime, press the Pause key Web Printer Function SelectionInput Prime Selection After selecting a Plug & Play, press the Pause key Expansion I/O Interface Type SelectionPlug & Play Selection After selecting a Label End type, press the Pause key Maxi Code Specification SelectionLabel End/Ribbon End Selection Use the Feed or Restart key to select a printing method Dump Mode SettingAfter selecting the receive buffer, press the Pause key After selecting a printing method, press the Pause key Required Label Length Data in the receive buffer is printed as followsReceive Buffer Size Basic Expansion Mode When the Pause key is pressed, Basic program is executed Not activated Activated Feed gap sensor Black mark sensor LAN Setting Date Setting Time Setting Cont Real Time Clock Setting 3 Low Battery Check SettingRTC Data Renewal Timing Setting IP Address Setting TCP/IP Feed and Pause keys Gateway IP Address Printer IP AddressThis parameter is to set an IP address This parameter is to set a Gateway IP address Socket Port Subnet MaskThis parameter is to set a Subnet Mask Dhcp Client ID This parameter is to enable DhcpDhcp This parameter is to set a Dhcp client ID Ascii code and Hex. code correspondence table Dhcp Host NameThis parameter is to set a Dhcp host name General Description Installing the Printer DriversIntroduction Installing the Printer Driver Parallel Interface Windows 98/Me E2-43 Windows 2000/XP E2-45 USB Interface E2-47 E2-48 E2-49 Finish button E2-51 E2-52 E2-53 Uninstalling the Printer Driver Adding/Deleting a LAN Port Adding a LAN Port Windows 98/ME Deleting a LAN Port Printer Driver Upgrades Others Using the Printer Driver Adjustment Print Test When using an optional Cutter Module Coordinate Fine Adjustment Position and Print Tone Fine AdjustmentFeed Amount Fine Adjustment Threshold Fine Adjustment Feed gap sensor After selecting a fine adjustment value, press the Pause key When setting +0.0 mm Position and Print Tone Fine Adjustment Restart Feed When setting -50.0 mm When setting +50.0 mm Print Tone Fine Adjustment Ribbon Motor Voltage Fine Adjustment Select the sensor to be adjusted by using the Feed key Threshold SettingJam errors Manually set Feed Gap Sensor Adjustment Upper Black Mark Sensor AdjustmentLower Black Mark Sensor Adjustment Lower Black Mark Sensor/Feed Gap Sensor Adjustment No media „ When using the Black Mark Sensor „ When using the Feed Gap Sensor Press and hold the Restart or Feed key for about 3 seconds „ Manual Threshold Setting„ Storing a No Media Level Voltage Feed Gap Sensor Used to stop printing temporarily On Line ModeOperation Panel Used to restart printing Operation Reset Press and hold the Restart key for 3 seconds or longer Print Head/Platen/ Sensors MaintenanceCleaning Covers and Panels Optional Cutter Module Error Messages Problems/Causes TroubleshootingError Messages Solutions Restart key Error Messages Problems/CauseMedia has run out Possible Problems Possible Problems Causes Attach the Cutter Cover properly Remove the jammed paper Clean the Cutter BladeLoad the ribbon properly Removing Jammed Media Model 852-TS22-QQ-R 852-TS22-QP-R Printer SpecificationsThis section describes the printer specifications Mail 4STATE Customer CODE, RSS14 Media Type Supply SpecificationsMedia Label Detection Area of the Transmissive Sensor Detection Area of the Reflective Sensor Effective Print Area Figure below shows the effective print area on the media Media type Description RibbonRecommended Media and Ribbon Types Combination of Media and Ribbon Care/Handling of the Media and RibbonRibbon type Description Media type Vellum paper and label Symbols in the message Appendix 1 Messages and Leds 100BASE LAN is being initialised Command error has occurredAnalyzing the command Dhcp Client is being initialised Following message appears Appendix 2 Interface Parallel interface Centronics Connector Standard Number of ports Power source Self power Connector Type BNumber of ports Connector RJ-45 LED status Link LED Serial interface Option B-SA704-RS-QM-R Wireless LAN Option B-SA704-WLAN-QM-R Expansion I/O Interface Option B-SA704-IO-QM-R Appendix 3 Print Samples CODE39 Full Ascii JAN8, EAN8 MSI Interleaved 2NW7 JAN13, EAN13 UPC-E EAN13+2 digits EAN13+5 digits UPC-E+2 digits UPC-E+5 digits EAN8+2 digits EAN8+5 digits Industrial 2 Data Matrix UPC-A+2 digitsUPC-A+5 digits Customer bar code of high priority QR code Appendix 4 Glossaries See Feed gap sensor See Black mark sensorMedia and ribbon USB Universal Serial Bus Index 3-1, A1-1 Index EO1-33055D