Printer IP Address, Gateway IP Address | Toshiba B-852 guide

2. PRINTER SETUP

ENGLISH VERSION EO1-33055

2.9 Setting an Operating Environment

2.9.7IP Address Setting (TCP/IP) (Cont.)

NOTES:

1.Set each 3-digit value by using the [RESTART] or [FEED] key.

[RESTART] key: Increment

[FEED] key: Decrement

Range: 0 to 255

2.Press the [PAUSE] key to move the cursor to the next 3-digit value.

3.After the last 3-digit value is set, press the [PAUSE] key to go to Gateway IP Address Setting.

NOTE:

After the last 3-digit value is set, press the [PAUSE] key to go to Subnet Mask Setting.

(1) Printer IP Address

This parameter is to set an IP address.

PRINTER IP ADRES

[PAUSE]

192 . 168 . 010 . 020

[PAUSE]

192 . 168 . 010 . 020

[PAUSE]

192 . 168 . 010 . 020

[PAUSE]

192 . 168 . 010 . 020

[PAUSE]

GATEWAY IP ADRES

(2) Gateway IP Address

This parameter is to set a Gateway IP address.

GATEWAY IP ADRES

[PAUSE]

192 . 168 . 010 . 020

[PAUSE]

192 . 168 . 010 . 020

[PAUSE]

192 . 168 . 010 . 020

[PAUSE]

192 . 168 . 010 . 020

[PAUSE]

SUBNET MASK

E2-36

Image 49

Toshiba B-852 owner manual Printer IP Address, This parameter is to set an IP address, Gateway IP Address

Contents

Series Vorsicht CE Compliance for EU only Series Waste Recycling information for users Meanings of Each Symbol Safety Summary Request Regarding Maintenance Precautions Table of Contents E4-1 E3-1E5-1 EA1-1 Product Overview Introduction FeaturesUnpacking Accessories Appearance DimensionsFront View Rear View Interior Operation Panel Option Name Type Description Options Setup Flow Printer SetupProcedure Manual threshold setting Installation Assembling the Supply Holder Frame Assembling the Accessories Connecting the Power Cord Loading the Media Installing the Media onto the Supply Holder UnitStraight and true through the printer Disassembling the Supply Holder Unit Spacer Supply Holder Loading Media into the Printer Print Head Element Head Block Release Lever Down Setting the Feed Gap Sensor Setting Sensor PositionsSetting the Black Mark Sensor Loading the Ribbon Connecting the Cables to Your Printer Turning on the Printer Turning the Printer Environment How to enter the System Mode While 2PARAMETER SET is displayed on the LCD Message Parameter SettingTime the Pause key is pressed, the sub menus are displayed Sequentially Character Code Selection Character Zero SelectionUse the Feed or Restart key to select a desired option After selecting a character code, press the Pause key After selecting a baud rate, press the Pause key Baud Rate SelectionData Length Selection After selecting a data length, press the Pause key Parity Selection Stop Bit Length SelectionFlow Control Code Selection After selecting a language, press the Pause key LCD Language SelectionAuto Forward Wait Selection After selecting an auto forward wait, press the Pause key Feed key Control Code Selection After selecting the Feed key function, press the Pause key Feed Key Function Selection After selecting a Kanji code, press the Pause key Kanji Code SelectionEuro Code Selection After selecting a Euro code, press the Pause key After selecting auto print head check, press the Pause key Auto Print Head Check SelectionCentronics Interface ACK/BUSY Timing Selection After selecting an ACK/BUSY timing, press the Pause key Input Prime Selection Web Printer Function SelectionAfter selecting the Input Prime, press the Pause key Plug & Play Selection Expansion I/O Interface Type SelectionAfter selecting a Plug & Play, press the Pause key Label End/Ribbon End Selection Maxi Code Specification SelectionAfter selecting a Label End type, press the Pause key After selecting the receive buffer, press the Pause key Dump Mode SettingUse the Feed or Restart key to select a printing method After selecting a printing method, press the Pause key Receive Buffer Size Data in the receive buffer is printed as followsRequired Label Length When the Pause key is pressed, Basic program is executed Basic Expansion Mode Not activated Activated Feed gap sensor Black mark sensor LAN Setting Time Setting Date Setting RTC Data Renewal Timing Setting Real Time Clock Setting 3 Low Battery Check SettingCont IP Address Setting TCP/IP Feed and Pause keys This parameter is to set an IP address Printer IP AddressGateway IP Address This parameter is to set a Gateway IP address This parameter is to set a Subnet Mask Subnet MaskSocket Port Dhcp This parameter is to enable DhcpDhcp Client ID This parameter is to set a Dhcp client ID This parameter is to set a Dhcp host name Dhcp Host NameAscii code and Hex. code correspondence table Introduction Installing the Printer DriversGeneral Description Parallel Interface Installing the Printer Driver Windows 98/Me E2-43 Windows 2000/XP E2-45 USB Interface E2-47 E2-48 E2-49 Finish button E2-51 E2-52 E2-53 Uninstalling the Printer Driver Adding a LAN Port Windows 98/ME Adding/Deleting a LAN Port Deleting a LAN Port Others Printer Driver Upgrades Using the Printer Driver Print Test Adjustment When using an optional Cutter Module Feed Amount Fine Adjustment Position and Print Tone Fine AdjustmentCoordinate Fine Adjustment Threshold Fine Adjustment Feed gap sensor When setting +0.0 mm After selecting a fine adjustment value, press the Pause key Position and Print Tone Fine Adjustment Restart Feed When setting +50.0 mm When setting -50.0 mm Print Tone Fine Adjustment Ribbon Motor Voltage Fine Adjustment Jam errors Threshold SettingSelect the sensor to be adjusted by using the Feed key Manually set Lower Black Mark Sensor Adjustment Upper Black Mark Sensor AdjustmentFeed Gap Sensor Adjustment Lower Black Mark Sensor/Feed Gap Sensor Adjustment No media „ When using the Feed Gap Sensor „ When using the Black Mark Sensor „ Storing a No Media Level Voltage „ Manual Threshold SettingPress and hold the Restart or Feed key for about 3 seconds Feed Gap Sensor Operation Panel On Line ModeUsed to stop printing temporarily Used to restart printing Press and hold the Restart key for 3 seconds or longer Operation Reset Cleaning MaintenancePrint Head/Platen/ Sensors Optional Cutter Module Covers and Panels Error Messages TroubleshootingError Messages Problems/Causes Solutions Media has run out Error Messages Problems/CauseRestart key Possible Problems Causes Possible Problems Load the ribbon properly Clean the Cutter BladeAttach the Cutter Cover properly Remove the jammed paper Removing Jammed Media This section describes the printer specifications Printer SpecificationsModel 852-TS22-QQ-R 852-TS22-QP-R Mail 4STATE Customer CODE, RSS14 Media Supply SpecificationsMedia Type Label Detection Area of the Reflective Sensor Detection Area of the Transmissive Sensor Figure below shows the effective print area on the media Effective Print Area Recommended Media and Ribbon Types RibbonMedia type Description Ribbon type Description Care/Handling of the Media and RibbonCombination of Media and Ribbon Media type Vellum paper and label Appendix 1 Messages and Leds Symbols in the message Analyzing the command Command error has occurred100BASE LAN is being initialised Dhcp Client is being initialised Following message appears Parallel interface Centronics Appendix 2 Interface Connector Number of ports Connector RJ-45 Number of ports Power source Self power Connector Type BStandard LED status Link LED Serial interface Option B-SA704-RS-QM-R Wireless LAN Option B-SA704-WLAN-QM-R Expansion I/O Interface Option B-SA704-IO-QM-R Appendix 3 Print Samples NW7 JAN13, EAN13 UPC-E EAN13+2 digits EAN13+5 digits JAN8, EAN8 MSI Interleaved 2CODE39 Full Ascii UPC-E+2 digits UPC-E+5 digits EAN8+2 digits EAN8+5 digits UPC-A+5 digits UPC-A+2 digitsIndustrial 2 Data Matrix Customer bar code of high priority QR code Appendix 4 Glossaries Media and ribbon See Black mark sensorSee Feed gap sensor USB Universal Serial Bus 3-1, A1-1 Index Index EO1-33055D