Manuals / Toshiba / Computer Equipment / Network Card

Toshiba e-STUDIO20, e-STUDIO25, e-STUDIO16 manual Precautions, Installation

Models: e-STUDIO25 e-STUDIO20 e-STUDIO16

1 184

Download 184 pages 14.59 Kb

Page 11

4. PRECAUTIONS

1. Installation

1 The e-STUDIO16/20/25 should be installed by an authorizedTOSHIBA service technician. Note

The packing material should be disposed of properly.

2 To obtain the best possible results, this machine should be used in conjunction with a dedicated AC power line at the following ratings:

220 - 240 VAC, 50/60 Hz, 1.4 kW or less (e-STUIDO16)

220 - 240 VAC, 50/60 Hz, 1.7 kW or less (e-STUIDO20/25)

110 - 127 VAC, 50/60 Hz, 1.4 kW or less (for Saudi Arabia 100V version only)

Note

1.The use of other appliances or other equipment on the same line as this machine may adversely affect performance and copy quality.

2.Be sure to use a 3-conductor, grounded wall outlet.

3.In areas where a 2-pin plug is used, the copier must be grounded for safety.

Never ground it to a gas pipe, a water pipe, or any other object not suitable for grounding.

3 After a suitable place has been selected for installation of the e-STUDIO16/20/25, please avoid frequent movement. Avoid excessive heat, dust, vibration and direct sunlight. Also, provide proper ventilation as the copier emits a small amount of ozone.

Note

1.The recommended environmental range for use is as follows:

• Temperature: 10~30°C/50~86°F

• Humidity:

20~85% RH

2.To ensure optimal operation, allow clearances of at least 80 cm on the left, 80 cm on the right and 10 cm in the rear (refer to the illustration below).

10 cm

80 cm

80 cm

The e-STUDIO should be placed near an outlet that is easily accessible.

8 PRECAUTIONS

Image 11

Toshiba e-STUDIO20, e-STUDIO25, e-STUDIO16 manual Precautions, Installation

Contents

Page Page ‘Sleep Mode’ Default Time ‘Super Power Save Mode’ Default Time‘Low Power Mode’ ‘Low Power Mode’ Default TimeSupplies / Parts Toshiba Quality is Second to NoneGeneral Toshiba Quality is Second to NoneToners Preface Preface Features of the e-STUDIO16/20/25Table of Contents Table of Contents 10-1 When the Graphic Symbol FlashesInstallation PrecautionsPage Page Before Making Copies STUDIO20/25 Description of the Optional EquipmentSTUDIO16 Brightness control Description of the Digital CopierMain Components Control Panel Description of the Digital CopierArrow Keys Automatic Function Clear ModeMessage Display Panel Pay attention to the following points PaperAcceptable Paper Types and Sizes Handling and Storing PaperChanging the Paper Size of the Cassette PaperTip Install the cassette into the copierAuto Job Start Turning on the Power Switch / Auto Job StartReady message appears Press the key to enter the program menu Cassette Size SettingSelect 01.MACHINE Defaults and press the key Selectkey .DEFAULT Settings and pressRepeat steps 4 to 6 to specify the paper size for other Paper cassettes, as necessaryPress Key to return to the initial screen for Copying Enter the 5-digit department code, and press key Department CodesMake copies, as you would normally 14BEFORE Making Copies HOW to Make Copies Copying Procedure Place originals General Copying ProcedureKey Set the desired copy modesPress Originals Setting OriginalsPlacing the Original on the Glass 6HOW to Make Copies Setting OriginalsPage After interrupt copying is finished, press the key again Interrupt CopyingPress Key Place the originalBasic Menu Automatic Paper Selection APS Paper SelectionSelect original size A4-R A5-R Manual Paper Selection Select desired copy mode and quantity as requiredPaper Selection Bypass Copying Reset Place sheets of copy paper on the stack feed bypass Bypass Copying by Specifying the Copy SizeSelect the desired copy size Reduction and Enlargement Copying Using Automatic Magnification Selection AMS Press the keySelect the desired image density and copy quantity Press Key and go to step Reduction and Enlargement CopyingReduce/Enlarge Press Key orOr key. Then press the key Select the desired reproduction ratio usingUse the or keys and select Zoom UP DOWN. Press the key Xxxx-Yxxx% appears next to zoom on the display ZoomKey on the control panel Select Manual by pressing the key Then press the key Copying in the Manual Mode Press KeyCopying with Copy Density Selection Place the original and press KeyPress the or key to select the desired image density Copying with Copy Density SelectionPlace the originals on the feed tray or on the glass If necessary, adjust the image densityOriginal Image Quality Selection Copy quantity16BASIC Menu Edit Menu Duplex Copying Key to return Sided Originals 1-Sided Copies default settingTo the initial screen for copying Confirm that Duplex is highlighted on the screenConfirm thatDUPLEX is highlighted on the screen Duplex CopyingSided Originals 2-Sided Copies How to place originals Place the first page of the originals first side on Then press Key Select 1 2 by pressing Key. PressSelect the desired paper cassette, image density Reproduction ratio and copy quantityHow to place originals on the glass Press the key on the control panel while Place the originals on the feed tray Press the key Sided Originals 1-Sided CopiesNecessary Select the desired copy mode usingBook-Type Originals 2-Sided Copies Press Key Specify the Book Margin then pressPress Key to select the desired paper Cassette. Press Key when finishedPress the key and select ON. Then press the key Dual page CopyingInitial screen for copying. The Edit Menu screen Appears Press Key to display the Dual Reverse. Then pressImage Shift Copying Specify the margin by using KeyDefault margin is 7 mm Edge Erase Copying Sided originals IN-1 Press the key and select 2IN1 or 4IN1 Then press the keyCopy quantity IN-1/4-IN-1Select the desired paper cassette, image density, While the Next Original? screen is being shown, if Select YES, set the next original and press the keyKey and specify whether the originals Magazine SortAre single-side or duplex. Then press Key Select YES, set the next original and press the key Magazine Sort Press the key to display ANNOTATION. Then AnnotationPress the key while ANNOTATIONis displayed Press the key to return to the initial screen for copyingAnnotation Press the key to displayMIRROR. Then press EditingMirror Image Press the key to displayEDITING. Then pressKey Press the key and select NEG/POS. Then EditingNegative/Positive Reversal Place the original on the glass or feed tray and press JOB BuildPlace the originals on the original feed tray Press the key Copying Mixed Size OriginalsTo MEMORY4. Then press the key JOB MemoryStoring a New Combination of Copy Modes Select desired copy modesJOB Memory Paper Type Menu List Program Menu Select02.WALKUP SCREENand press the key Walkup ScreenAuto Clear TimersSelect 2. Auto LOW Power and press the key TimersAuto Low Power Select 03. Timers and press the keySelect 3. Auto Sleep and press the key Select 01. Machine Defaults and press the keySelect the desired Automatic Sleep Time by using Automatic SleepClearing the Automatic Sleep mode Clearing the Super Energy Saver modeSelect 2.ON and press the key Weekly TimerSelect the 04. Weekly Timer and press the key Enter a turn off time for the copier and press the key Weekly Timer Sunday Monday TuesdaySelect 1.OFF, and press Key Canceling WeeklyTimerSelect01. Machine Defaults and press the key Select 04. Weekly Timer and press the keyKey to adjust the volume Speaker VolumeRepeat steps 5 to 7 to adjust the volume of other Selectkey. the desired volume control and pressSelect 1.YES or 2.NO and press the key Department Code SettingDepartment Code Setting Department CodeDepartment Code Entry Enter a department number and press Department CodeMaster Code Entry Enter the desired master code and pressSelect 4.COUNT Clear and press Key Clearing Department Code CountersSelect 1.DELETE and press Key Deleting Department CodeChange Department Code Setting Same department code cannot be entered for other Enter a department code and press KeySelect 1.DEPARTMENT Code and press the key Report PrintingCanceling/Resuming Department Management Screen returns to the Copy Setup screen Copy SetupSelect 02.IMAGE Mode and press Copy SetupKey to enter the manual mode Select 02.COPY Setup and press KeySelect a paper ejection method and press the key Select 04.FINISHING and pressSet the system for 12 hours or 24 hours operation Select 03. Initial SETUP. Then press the keyDate and Time Select 01. Date & TIME. Then press the keyKey.Select 04. Month MODE. Then press Date and TimeEnter the hour 00 to 12 if 12HR format has been Select and minute 00 to 59 by using the numericSelect AM or PM by using Key Check that all the settings are correctMessage display panel Change Display Panel LanguageSelect 02.LANGUAGE and press the key Select the desired display language and press the keyFunction List Total Counter Finishing Mode Selection Job Separator option Finishing Mode SelectionFinisher option for e-STUDIO20/25 only Offset Tray optionPress the key. TheFINISHING screen appears NON-SORT CopyingConfirm that Nonsort is displayed. Then press Key If Finishingsort is not displayed, press Key and select the sort modeSort Copying Place the originals in the feederCopier starts copying and collates the copies into sets Offset Copying Alternation Select YES, set the next original and press AlternationCopier starts copying. In this copying mode, as sets Ratio Press Key Select the Staple modeStapling KeysSelect Staple from the Finishing menu by pressing Stapling When the optional Stapler kit is installedWhen the Graphic Symbol Flashes Description of the Graphic Symbols Push the cassette straight in until it comes to a stop Loading PaperAdding Paper to the Cassettes Close the cover of the large-capacity feeder Loading PaperReplacing Toner Cartridge Replacing Toner Cartridge STUDIO20/25 B a aAdditional Explanation STUDIO16Automatic duplexing units Replacing Process UnitReplacing Process Unit Open the stack feed bypassAlways hold the Process Unit by the colored handle Replacing Process Unit Replacing Ozone Filter Press the button to unlock and open the cover Clearing Paper JAMPage Lift the original tray Clearing Paper JAMPage Paper Misfeed in the Large-Capacity Feeder Option for e-STUDIO20/25Open the cover Remove any misfed paper Reset the paper on the bypass tray 18WHEN the Graphic Symbol Flashes Page Automatic duplexing unit to normal position if installed Page It pushing down the blue lever Page Adding Staples Page Staple kit option Adding StaplesInsert the cartridge until it clicks Attach the finisher to the copier Removing Jammed StaplesPress the lever 1 and pull up the staple guide knob Slide forward and lift up the staple coverRemoving Jammed Staples Calling for Service Periodic Maintenance User Test Mode Auto Test Automatic Test ModeIndividual Test Summary Individual Test ModeADF Test ADF Test Number CORRECT? YES Select02.INDIVIDUALTEST and press Key KEY TestIf even one LED did not light, select the 2.NG LED TestIf all the LEDs turned on, select the 1.OKand press If all elements of the LCD turned on and off normally LCD TestAfter checking, press Key If the volumes are output normally, select1.OKSpeaker Test Switch Test Test Print Printing a Test Result Maintenance Items to inspect once a week Daily InspectionItems to inspect every morning Close the front cover Cleaning the WireCleaning the Wire Copier does not start Simple TroubleshootingDisplay does not change when keys are pressed Copy density is too high Simple Trouble ShootingCopies are stained Copy density is too lowFunctions cannot be set Copy images are blurredImages are partially missing 8MAINTENANCE Specifications & Options STUDIO16/20/25 Specifications Reversing Automatic Document Feeder Specification of OptionsAutomatic Document Feeder Paper Feed Unit Specification of OptionsAutomatic Duplexing Unit Offset Tray Job SeparatorStapler Finisher for e-STUDIO20/25 onlyStack Feed Bypass Memory Kit STUDIO16/20/25 Copy Function Combination Table Copy Function Combination Matrix10-9 10-10SPECIFICATIONS & Options