Power Control Exh, Stand-by Immediate E0/94 | Toshiba MK6017MAP

360014937
10.8.20 Power Control				(Exh)

	COMMAND CODE			1 1 1 0 X X X X	REGISTER
		REGISTER SETTING			NORMAL COMPLETION
	DR		drive no.		no change
	CY				no change
	HD				no change
	SN				no change
	SC		shown below		00/FFH (for E5/98 command)
					no change (for other command)
	FT				no change

Power Control is a group of commands which controls low power mode in the drive. The drive has three types of power mode:

Idle, Stand-by and Sleep mode

At the completion of disk access, the drive automatically enters the idle mode.

There are two ways to shift to the stand-by mode ( to stop rotation of spindle motor ).

By a command from the host

By internal timer

The internal timer is set by Stand-by or Idle command. The period is equivalent to SC x 5 seconds. If Stand-by or Idle command is executed when SC=0 and the drive receives no access from host for 45 minutes, the drive automatically enters the stand-by mode.

If the drive receives disk access command from the host when it is in stand-by mode , the spindle starts rotating and the drive executes read/write operation.

After power on, the spindle starts rotating and enters the idle mode. During idle or stand-by, READY bit is set and the drive is ready to receive a command.

To be specific , there are four different sub-commands defined by lower 4 bits of command as follows. The drive is in the idle mode and the auto stand-by ( timer setting:45 min.) when it is in default condition after power- on.

10.8.20.1 Stand-by Immediate (E0/94)

SC=X (Don't care)

The drive enters the stand-by mode immediately by this command. If the drive is already in the stand-by mode, it does no-operation and the stand-by timer doesn’t start .The drive issues an interrupt and reports the host that the command has been completed before it virtually enters the stand-by mode .

10.8.20.2 Idle Immediate (E1/95)

SC=X

The drive enters the idle mode immediately by this command. If the drive is already in the idle mode, it does no-operation. If stand-by timer is enabled, timer will start. After the drive enters the idle mode, the drive issues interrupt to report the host that the command has been completed.

Copyright ©2000 Toshiba corporation. All rights reserved.

- 570 -

Image 70

Toshiba MK6017MAP manual Power Control Exh, Stand-by Immediate E0/94, Idle Immediate E1/95, Sc=X

Contents

Toshiba Revised ContentsREV STGE.PER Ｓａｆｅｔｙ Usage Restrictions Safety Copyright 2000 Toshiba corporation. All rights reserved 506 Table of Contents Security SET Password Protocol Table of Figures Scope Copyright 2000 Toshiba corporation. All rights reserved 512 KEY Features Basic Specification Performance Supply Voltage Power ConsumptionPower Sequence Energy Consumption Efficiency Drive Orientation DimensionWeight Mounting Instructions Installation Screwing MK6017MAP Dimensions MK6017MAP Mounting Recommendation Vibration Temperature and HumidityTemperature Shock Safety Standards Acoustics （Sound Power ）Altitude Mean Time to Failure Mttf Error RatePreventive Maintenance PM Product Life Load/Unload Cabling Interface ConnectorCable Cable length and capacitance Electrical specificationDC input/output Characteristics 10.2.2.1 Input Output Interface connector ATA interface connector Dasp Ground Pin AssignmentPdiag ／-CBLID Ground Reserved Signal Treatment Dasp Signal Description Series resistance Copyright 2000 Toshiba corporation. All rights reserved 532 Host Interface Timing Program I/O Write Timing Program I/O Read Timing ATA-2 Specifications Single Word DMA Write Timing ATA-2 Specification Single Word DMA Read Timing ATA/ATAPI-5 Specifications Multiword DMA Write Timing Multiword DMA Read Timing Ultra DMA Timing Hdmardy Sustained Ultra DMA data in burst Device terminating an Ultra DMA data in burst CRC Host terminating an Ultra DMA data in burst Initiating an Ultra DMA data out burst Ddmardy Sustained Ultra DMA data out burst Host terminating an Ultra DMA data out burst Device terminating an Ultra DMA data out burst ATA/ATAPI specifications Reset Timing Grounding Address Decoding 1 Register map Register Description Error Register Security commandsOperational Mode Disk Access command Diagnostic ModeSmart command Initialize Device Parameters command Cylinder Low Registers Smart commandsSector Number Register Cylinder High Registers Device/Head Register DEV HS3 HS2 HS1 HS0 Status Register BSY Drdy DSC3 DRQ Corr IDX ERR Command Register Command Code Device Address register4 Alternate Status RegisterDevice Control Register Srst IEN Command Descriptions Recalibrate5 1xh Nop 00hFlush Cache E7h Read Long6 22h/23h Read Sector 20h/21hWrite Sector 30h/31h Read Verify 40h Write Long7 32h/33hWrite Verify8 3Ch Format Track 50h Seek 7xh Execute Diagnostics 90hToshiba Specific Initialize Device Parameters 91h Read Multiple C4h Write Multiple C5h Set Multiple Mode C6h Read DMA C8h/C9h Write DMA CAh/CBh Idle Immediate E1/95 Power Control ExhStand-by Immediate E0/94 SC=X Idle E3/97 Check Power Mode E5/98Stand-by E2/96 Sleep E6/99 Read Buffer E4h Write Buffer E8h Identify Device ECh Word Description Hex 360014937 2 Identify Information 360014937 3 Identify Information 360014937 4 Identify Information =ATA Toshiba MK6017MAP MK6017MAP Copyright 2000 Toshiba corporation. All rights reserved 581 Copyright 2000 Toshiba corporation. All rights reserved 582 Copyright 2000 Toshiba corporation. All rights reserved 583 Timer Actual Value Copyright 2000 Toshiba corporation. All rights reserved 585 Set Max Address F9h Read Native Max Address F8h Set Features EFh Features FT register defines following selections Security SET Password F1h Security Set Password information Security Unlock F2h Security Erase Prepare F3h Security Erase Unit F4h Security Freeze Lock F5h Security Disable Password F6h Smart Function Set 10.8.33.1 Smart Read Attribute values Attribute Name Value Definition Copyright 2000 Toshiba corporation. All rights reserved 596 10.8.33.2 Smart Read Attribute thresholds Smart Enable Disable Attribute Autosave 10.8.33.4 Smart Save Attribute Values Off-line mode 10.8.33.5 Smart Execute Off-line Immediate Captive mode 10.8.33.6 Command CodeRegister Setting Normal Completion Register Command data structure Error data structure Self-test log sector Self-test index 10.8.33.7 Smart Write Log Sector Smart Enable Operations 10.8.33.9 Smart Disable Operations Smart Enable/Disable Automatic Off-line Smart Return Status Security mode default setting Initial setting of the user password Unlock Security mode operation from power-onUnit Password lost Command Table Attributes Smart function default settingAttributes values Performance Idle Adaptive Power Mode ControlLow Power Idle Active Idle Reset Register Power on Hardware Reset Software Reset LOW Master/Slave ConfigurationHigh Automatic Write Reallocation Cache MemoryCache Operations Protocol PIO data in commands Commands for this class are PIO data out commands PIO data out protocol Non-data commands Non-data protocol DMA data transfer commands Ultra DMA Copyright 2000 Toshiba corporation. All rights reserved 624 = DD2 XOR CRCOUT13 = DD0 XOR CRCOUT15= DD1 XOR CRCOUT14 = DD3 XOR CRCOUT12 Function and Intervals Timeout Other timings