Manuals / Toshiba / Photography / Camcorder

Toshiba MK6017MAP manual Set Features EFh, Features FT register defines following selections

Models: MK6017MAP

1 126

Download 126 pages 58.41 Kb

Page 87

360014937

10.8.26 Set Features			(EFh)

	COMMAND CODE			1 1 1 0 1 1 1 1	REGISTER
		REGISTER SETTING			NORMAL COMPLETION
	DR		DRIVE No.		no change
	CY				no change
	HD				no change
	SN				no change
	SC	Mode Selection for Data Transfer(*2)			no change
	FT		Features(*1)		no change

(*1) Features: FT register defines following selections.

02H	Enable write cache feature
03H	Select data transfer mode
05H	Enable advanced power management
44H	ECC length is 46 bytes during Read/Write Long command
55H	Disable read look-ahead feature
66H	Disable reverting to power on defaults by soft reset
82H	Disable write cache feature
85H	Disable advanced power management
AAH	Enable read look-ahead feature
BBH	ECC length is 4 bytes during Read/Write Long command
CCH	Enable reverting to power on defaults by soft reset
others	Invalid (reporting with Aborted Command Error)

(*2)Mode selection for data transfer is specified in sector count register. Upper 5 bits show transfer mode and lower 3 bits show mode figure.

PIO default transfer mode	00000 000
PIO default transfer mode, disable IORDY	00000 001
PIO flow control transfer mode nnn	00001 nnn
Single word DMA mode nnn	00010 nnn
Multiword DMA mode nnn	00100 nnn
Ultra DMA mode nnn	01000 nnn
Reserved	10000 nnn

PIO default mode is mode 4 flow control. DMA default mode is Multiword word DMA mode 2.

The level of Advanced Power Management function is set in Sector count register.

C0h-FEh	……	Mode0 (Power save up to		Performance Idle)
80h-BFh	……	Mode1	(Power save up to	Low Power Idle)
01h-7Fh	……	Mode2	(Power save up to	Standby)
00h,FFh	……	Aborted

Transition time of power save is changed dynamically in Mode1 and Mode2 due to Adaptive power control function. The function level is set to Mode1 when Advanced Power Management function is disabled.

If FT register has any other value, the drive rejects the command with Abort Command error.

Default settings after power on or hard reset are:

Data transfer mode of Multiword DMA mode 2, PIO mode 4 flow control,

4 bytes ECC, look-ahead read enabled, write cache enabled, advanced power management enabled, READ/WRITE Multiple command enabled (16 sectors)

and reverting to power on defaults by soft reset disabled.

Copyright © 2000 Toshiba corporation. All rights reserved.

- 587 -

Image 87

Toshiba MK6017MAP manual Set Features EFh, Features FT register defines following selections

Contents

Toshiba STGE.PER ContentsREV RevisedＳａｆｅｔｙ Usage Restrictions Safety Copyright 2000 Toshiba corporation. All rights reserved 506 Table of Contents Security SET Password Protocol Table of Figures Scope Copyright 2000 Toshiba corporation. All rights reserved 512 KEY Features Basic Specification Performance Energy Consumption Efficiency Power ConsumptionPower Sequence Supply VoltageMounting Instructions DimensionWeight Drive OrientationScrewing InstallationMK6017MAP Dimensions MK6017MAP Mounting Recommendation Shock Temperature and HumidityTemperature VibrationAcoustics （Sound Power ） Safety StandardsAltitude Product Life Error RatePreventive Maintenance PM Mean Time to Failure MttfLoad/Unload Interface Connector CablingCable Output Electrical specificationDC input/output Characteristics 10.2.2.1 Input Cable length and capacitanceATA interface connector Interface connectorGround Reserved Pin AssignmentPdiag ／-CBLID Dasp GroundDasp Signal TreatmentSeries resistance Signal DescriptionCopyright 2000 Toshiba corporation. All rights reserved 532 Program I/O Write Timing Host Interface TimingProgram I/O Read Timing Single Word DMA Write Timing ATA-2 SpecificationsSingle Word DMA Read Timing ATA-2 SpecificationMultiword DMA Write Timing ATA/ATAPI-5 SpecificationsMultiword DMA Read Timing Hdmardy Ultra DMA TimingSustained Ultra DMA data in burst CRC Device terminating an Ultra DMA data in burstHost terminating an Ultra DMA data in burst Ddmardy Initiating an Ultra DMA data out burstSustained Ultra DMA data out burst Host terminating an Ultra DMA data out burst Device terminating an Ultra DMA data out burst ATA/ATAPI specifications Grounding Reset Timing1 Register map Address DecodingRegister Description Security commands Error RegisterOperational Mode Initialize Device Parameters command Diagnostic ModeSmart command Disk Access commandCylinder High Registers Smart commandsSector Number Register Cylinder Low RegistersDEV HS3 HS2 HS1 HS0 Device/Head RegisterBSY Drdy DSC3 DRQ Corr IDX ERR Status RegisterCommand Register Command Code Srst IEN Alternate Status RegisterDevice Control Register Device Address register4Command Descriptions Nop 00h Recalibrate5 1xhFlush Cache E7h Read Sector 20h/21h Read Long6 22h/23hWrite Sector 30h/31h Write Long7 32h/33h Read Verify 40hWrite Verify8 3Ch Format Track 50h Execute Diagnostics 90h Seek 7xhToshiba Specific Initialize Device Parameters 91h Read Multiple C4h Write Multiple C5h Read DMA C8h/C9h Set Multiple Mode C6hWrite DMA CAh/CBh SC=X Power Control ExhStand-by Immediate E0/94 Idle Immediate E1/95Sleep E6/99 Check Power Mode E5/98Stand-by E2/96 Idle E3/97Write Buffer E8h Read Buffer E4hIdentify Device ECh Hex Word Description360014937 2 Identify Information 360014937 3 Identify Information 360014937 4 Identify Information =ATA Toshiba MK6017MAP MK6017MAP Copyright 2000 Toshiba corporation. All rights reserved 581 Copyright 2000 Toshiba corporation. All rights reserved 582 Copyright 2000 Toshiba corporation. All rights reserved 583 Timer Actual Value Copyright 2000 Toshiba corporation. All rights reserved 585 Read Native Max Address F8h Set Max Address F9hFeatures FT register defines following selections Set Features EFhSecurity Set Password information Security SET Password F1hSecurity Erase Prepare F3h Security Unlock F2hSecurity Freeze Lock F5h Security Erase Unit F4hF6h Security Disable PasswordSmart Function Set Smart Read Attribute values 10.8.33.1Attribute Name Value Definition Copyright 2000 Toshiba corporation. All rights reserved 596 Smart Read Attribute thresholds 10.8.33.210.8.33.4 Smart Save Attribute Values Smart Enable Disable Attribute Autosave10.8.33.5 Smart Execute Off-line Immediate Off-line modeCaptive mode Register Command CodeRegister Setting Normal Completion 10.8.33.6Command data structure Error data structure Self-test log sector Self-test index 10.8.33.7 Smart Write Log Sector 10.8.33.9 Smart Disable Operations Smart Enable OperationsSmart Return Status Smart Enable/Disable Automatic Off-lineInitial setting of the user password Security mode default settingSecurity mode operation from power-on UnlockUnit Password lost Command Table Smart function default setting AttributesAttributes values Active Idle Adaptive Power Mode ControlLow Power Idle Performance IdleRegister Power on Hardware Reset Software Reset ResetMaster/Slave Configuration LOWHigh Cache Memory Automatic Write ReallocationCache Operations Protocol Commands for this class are PIO data in commandsPIO data out protocol PIO data out commandsNon-data protocol Non-data commandsDMA data transfer commands Ultra DMA Copyright 2000 Toshiba corporation. All rights reserved 624 = DD3 XOR CRCOUT12 = DD0 XOR CRCOUT15= DD1 XOR CRCOUT14 = DD2 XOR CRCOUT13Other timings Function and Intervals Timeout