Smart Return Status | Toshiba MK6017MAP specs

360014937

10.8.33.10 SMART Return Status

COMMAND CODE			1 0 1 1 0 0 0 0	REGISTER
	REGISTER SETTING			NORMAL COMPLETION
DR		DRIVE No.		no change
CY			C24Fh	C24Fh/2CF4h
HD				no change
SN				no change
SC				no change
FT			DAh	no change

If an impending failure is not predicted, the drive sets the Cylinder Low register to 4Fh and the Cylinder High register to C2h. If an impending failure is predicted, the drive sets the Cylinder Low register to F4h and the Cylinder High register to 2Ch.

This command is used to communicate the reliability status of the drive to the host’s request. Upon receipt of this command the drive sets BSY, saves any parameters monitored by the drive to non-volatile memory and checks the drive condition.

10.8.33.11 SMART Enable/Disable Automatic Off-line

COMMAND CODE			1 0 1 1 0 0 0 0	REGISTER
	REGISTER SETTING			NORMAL COMPLETION
DR		DRIVE No.		no change
CY			C24Fh	no change
HD				no change
SN				no change
SC		00h/F8h		no change
FT			DBh	no change

This subcommand enables and disables the optional feature that causes the device to perform the set of off-line data collection activities that automatically collect attribute data in an off-line mode and then save this data to the device’s non-volatile memory. This subcommand may either cause the device automatically initiate or resume performance of its off-line data collection activities; or this command may cause the automatic off-line data collection feature to be disabled.

A value of zero written by the host into the device’s Sector Count register before issuing this subcommand shall cause the feature to be disabled. Disabling this feature does not preclude the device from saving attribute values to non-volatile memory during some other normal operation such as during a power-on or power-off sequence or during an error recovery sequence.

A value of F8h written by the host into the device’s Sector Count register before issuing this command shall cause this feature to be enabled. Any other non-zero value written by the host into this register before issuing this subcommand is vendor specific.

Automatic off-line data collection is executed every 24 power-on hours.

Copyright ©2000 Toshiba corporation. All rights reserved.

- 608 -

Image 108

Toshiba MK6017MAP manual Smart Return Status, Smart Enable/Disable Automatic Off-line

Contents

Toshiba Contents REVRevised STGE.PER Ｓａｆｅｔｙ Usage Restrictions Safety Copyright 2000 Toshiba corporation. All rights reserved 506 Table of Contents Security SET Password Protocol Table of Figures Scope Copyright 2000 Toshiba corporation. All rights reserved 512 KEY Features Basic Specification Performance Power Consumption Power SequenceSupply Voltage Energy Consumption Efficiency Dimension WeightDrive Orientation Mounting Instructions Installation Screwing MK6017MAP Dimensions MK6017MAP Mounting Recommendation Temperature and Humidity TemperatureVibration Shock Acoustics （Sound Power ） Safety StandardsAltitude Error Rate Preventive Maintenance PMMean Time to Failure Mttf Product Life Load/Unload Interface Connector CablingCable Electrical specification DC input/output Characteristics 10.2.2.1 InputCable length and capacitance Output Interface connector ATA interface connector Pin Assignment Pdiag ／-CBLIDDasp Ground Ground Reserved Signal Treatment Dasp Signal Description Series resistance Copyright 2000 Toshiba corporation. All rights reserved 532 Host Interface Timing Program I/O Write Timing Program I/O Read Timing ATA-2 Specifications Single Word DMA Write Timing ATA-2 Specification Single Word DMA Read Timing ATA/ATAPI-5 Specifications Multiword DMA Write Timing Multiword DMA Read Timing Ultra DMA Timing Hdmardy Sustained Ultra DMA data in burst Device terminating an Ultra DMA data in burst CRC Host terminating an Ultra DMA data in burst Initiating an Ultra DMA data out burst Ddmardy Sustained Ultra DMA data out burst Host terminating an Ultra DMA data out burst Device terminating an Ultra DMA data out burst ATA/ATAPI specifications Reset Timing Grounding Address Decoding 1 Register map Register Description Security commands Error RegisterOperational Mode Diagnostic Mode Smart commandDisk Access command Initialize Device Parameters command Smart commands Sector Number RegisterCylinder Low Registers Cylinder High Registers Device/Head Register DEV HS3 HS2 HS1 HS0 Status Register BSY Drdy DSC3 DRQ Corr IDX ERR Command Register Command Code Alternate Status Register Device Control RegisterDevice Address register4 Srst IEN Command Descriptions Nop 00h Recalibrate5 1xhFlush Cache E7h Read Sector 20h/21h Read Long6 22h/23hWrite Sector 30h/31h Write Long7 32h/33h Read Verify 40hWrite Verify8 3Ch Format Track 50h Execute Diagnostics 90h Seek 7xhToshiba Specific Initialize Device Parameters 91h Read Multiple C4h Write Multiple C5h Set Multiple Mode C6h Read DMA C8h/C9h Write DMA CAh/CBh Power Control Exh Stand-by Immediate E0/94Idle Immediate E1/95 SC=X Check Power Mode E5/98 Stand-by E2/96Idle E3/97 Sleep E6/99 Read Buffer E4h Write Buffer E8h Identify Device ECh Word Description Hex 360014937 2 Identify Information 360014937 3 Identify Information 360014937 4 Identify Information =ATA Toshiba MK6017MAP MK6017MAP Copyright 2000 Toshiba corporation. All rights reserved 581 Copyright 2000 Toshiba corporation. All rights reserved 582 Copyright 2000 Toshiba corporation. All rights reserved 583 Timer Actual Value Copyright 2000 Toshiba corporation. All rights reserved 585 Set Max Address F9h Read Native Max Address F8h Set Features EFh Features FT register defines following selections Security SET Password F1h Security Set Password information Security Unlock F2h Security Erase Prepare F3h Security Erase Unit F4h Security Freeze Lock F5h Security Disable Password F6h Smart Function Set 10.8.33.1 Smart Read Attribute values Attribute Name Value Definition Copyright 2000 Toshiba corporation. All rights reserved 596 10.8.33.2 Smart Read Attribute thresholds Smart Enable Disable Attribute Autosave 10.8.33.4 Smart Save Attribute Values Off-line mode 10.8.33.5 Smart Execute Off-line Immediate Captive mode Command Code Register Setting Normal Completion10.8.33.6 Register Command data structure Error data structure Self-test log sector Self-test index 10.8.33.7 Smart Write Log Sector Smart Enable Operations 10.8.33.9 Smart Disable Operations Smart Enable/Disable Automatic Off-line Smart Return Status Security mode default setting Initial setting of the user password Security mode operation from power-on UnlockUnit Password lost Command Table Smart function default setting AttributesAttributes values Adaptive Power Mode Control Low Power IdlePerformance Idle Active Idle Reset Register Power on Hardware Reset Software Reset Master/Slave Configuration LOWHigh Cache Memory Automatic Write ReallocationCache Operations Protocol PIO data in commands Commands for this class are PIO data out commands PIO data out protocol Non-data commands Non-data protocol DMA data transfer commands Ultra DMA Copyright 2000 Toshiba corporation. All rights reserved 624 = DD0 XOR CRCOUT15 = DD1 XOR CRCOUT14= DD2 XOR CRCOUT13 = DD3 XOR CRCOUT12 Function and Intervals Timeout Other timings