Toshiba MK6017MAP instruction

360014937

SAFETY

Observe the following to prevent failure, malfunction or data loss.

NOTE

●Follow the specifications for 6. POWER SUPPLY (page516), 8. ENVIRONMENT (page 522, 523), etc. when using.

Failure to do so may cause damage to the drive.

●Observe cautions in 7.4 MOUNTING INSTRUCTION (page517) and 9.6 LOAD / UNLOAD (page525 ) when handling, setting up, or using the drive.

●Take anti-static measures in order to avoid damage to the drive when handling it.

The drive uses parts susceptible to damage due to ESD (electrostatic discharge).

Wear ESD proof wrist strap in accordance with the usage specified when handling a drive that is not in an anti-static protection bag.

●There is a certain probability of the drive causing failure including data error or data loss.

Take preventive steps such as backing up data etc. without exception in order to prevent loss etc. in cases where data loss may result in loss or damage.

Please include this in the instruction manual etc. of the system in which this device is used and ensure that users are made thoroughly aware of it.

●Inserting or pulling out the drive when the power is turned on may cause damage to the drive.

Exchange the drive etc. after the power of HDD is turned off.

●Extreme shock to the drive may cause damage to it, data corruption, etc..

Do not subject the drive to extreme shock such as dropping, upsetting or crashing against other objects.

●Do not touch the top cover since application of force to it may cause damage to the drive.

●Do not stack the drive on another drive or on other parts etc. or stack them on top of it during storage or transportation.

Shock or weight may cause parts distortion etc..

●Labels and the like attached to the drive are also used as a seal for maintenance of its performance.

Do not remove them from the drive.

●Attachment of dielectric materials such as metal powder, liquid, etc. to live parts such as printed circuit board patterns or pins etc. may cause damage to the drive.

Avoid attachment of these materials.

●Do not place objects which generate magnetic fields such as magnets, speakers, etc. near the drive.

Magnetism may cause damage to the drive or data loss.

Copyright ©2000 Toshiba corporation. All rights reserved.

- 506 -

Image 6

Toshiba MK6017MAP manual Copyright 2000 Toshiba corporation. All rights reserved 506

Contents

Toshiba Revised ContentsREV STGE.PER Ｓａｆｅｔｙ Usage Restrictions Safety Copyright 2000 Toshiba corporation. All rights reserved 506 Table of Contents Security SET Password Protocol Table of Figures Scope Copyright 2000 Toshiba corporation. All rights reserved 512 KEY Features Basic Specification Performance Supply Voltage Power ConsumptionPower Sequence Energy Consumption Efficiency Drive Orientation DimensionWeight Mounting Instructions Installation Screwing MK6017MAP Dimensions MK6017MAP Mounting Recommendation Vibration Temperature and HumidityTemperature Shock Acoustics （Sound Power ） Safety StandardsAltitude Mean Time to Failure Mttf Error RatePreventive Maintenance PM Product Life Load/Unload Interface Connector CablingCable Cable length and capacitance Electrical specificationDC input/output Characteristics 10.2.2.1 Input Output Interface connector ATA interface connector Dasp Ground Pin AssignmentPdiag ／-CBLID Ground Reserved Signal Treatment Dasp Signal Description Series resistance Copyright 2000 Toshiba corporation. All rights reserved 532 Host Interface Timing Program I/O Write Timing Program I/O Read Timing ATA-2 Specifications Single Word DMA Write Timing ATA-2 Specification Single Word DMA Read Timing ATA/ATAPI-5 Specifications Multiword DMA Write Timing Multiword DMA Read Timing Ultra DMA Timing Hdmardy Sustained Ultra DMA data in burst Device terminating an Ultra DMA data in burst CRC Host terminating an Ultra DMA data in burst Initiating an Ultra DMA data out burst Ddmardy Sustained Ultra DMA data out burst Host terminating an Ultra DMA data out burst Device terminating an Ultra DMA data out burst ATA/ATAPI specifications Reset Timing Grounding Address Decoding 1 Register map Register Description Security commands Error RegisterOperational Mode Disk Access command Diagnostic ModeSmart command Initialize Device Parameters command Cylinder Low Registers Smart commandsSector Number Register Cylinder High Registers Device/Head Register DEV HS3 HS2 HS1 HS0 Status Register BSY Drdy DSC3 DRQ Corr IDX ERR Command Register Command Code Device Address register4 Alternate Status RegisterDevice Control Register Srst IEN Command Descriptions Nop 00h Recalibrate5 1xhFlush Cache E7h Read Sector 20h/21h Read Long6 22h/23hWrite Sector 30h/31h Write Long7 32h/33h Read Verify 40hWrite Verify8 3Ch Format Track 50h Execute Diagnostics 90h Seek 7xhToshiba Specific Initialize Device Parameters 91h Read Multiple C4h Write Multiple C5h Set Multiple Mode C6h Read DMA C8h/C9h Write DMA CAh/CBh Idle Immediate E1/95 Power Control ExhStand-by Immediate E0/94 SC=X Idle E3/97 Check Power Mode E5/98Stand-by E2/96 Sleep E6/99 Read Buffer E4h Write Buffer E8h Identify Device ECh Word Description Hex 360014937 2 Identify Information 360014937 3 Identify Information 360014937 4 Identify Information =ATA Toshiba MK6017MAP MK6017MAP Copyright 2000 Toshiba corporation. All rights reserved 581 Copyright 2000 Toshiba corporation. All rights reserved 582 Copyright 2000 Toshiba corporation. All rights reserved 583 Timer Actual Value Copyright 2000 Toshiba corporation. All rights reserved 585 Set Max Address F9h Read Native Max Address F8h Set Features EFh Features FT register defines following selections Security SET Password F1h Security Set Password information Security Unlock F2h Security Erase Prepare F3h Security Erase Unit F4h Security Freeze Lock F5h Security Disable Password F6h Smart Function Set 10.8.33.1 Smart Read Attribute values Attribute Name Value Definition Copyright 2000 Toshiba corporation. All rights reserved 596 10.8.33.2 Smart Read Attribute thresholds Smart Enable Disable Attribute Autosave 10.8.33.4 Smart Save Attribute Values Off-line mode 10.8.33.5 Smart Execute Off-line Immediate Captive mode 10.8.33.6 Command CodeRegister Setting Normal Completion Register Command data structure Error data structure Self-test log sector Self-test index 10.8.33.7 Smart Write Log Sector Smart Enable Operations 10.8.33.9 Smart Disable Operations Smart Enable/Disable Automatic Off-line Smart Return Status Security mode default setting Initial setting of the user password Security mode operation from power-on UnlockUnit Password lost Command Table Smart function default setting AttributesAttributes values Performance Idle Adaptive Power Mode ControlLow Power Idle Active Idle Reset Register Power on Hardware Reset Software Reset Master/Slave Configuration LOWHigh Cache Memory Automatic Write ReallocationCache Operations Protocol PIO data in commands Commands for this class are PIO data out commands PIO data out protocol Non-data commands Non-data protocol DMA data transfer commands Ultra DMA Copyright 2000 Toshiba corporation. All rights reserved 624 = DD2 XOR CRCOUT13 = DD0 XOR CRCOUT15= DD1 XOR CRCOUT14 = DD3 XOR CRCOUT12 Function and Intervals Timeout Other timings