Signal Treatment, Dasp | Toshiba MK6017MAP manual

360014937

10.3.3 Signal Treatment

Driver types and requirements for the signal pull- up and down are as follows. Resistor requirement is minimum for the host. - IO16 is pulled up in the drive with certain value so that the Vol is obtained to run with a host that has large value of pull up

resistor.	- CS0 and - CS1 are also pulled up for better noise immunity.
	Table 10.3-2 Signal treatment
SIGNAL	Driven by	TYPE	By host		By drive
- RESET	host	TP			10kΩPU
DD 0:15	bi-direction	TS
DMARQ	drive	TS	5.6 k Ω	PD
- DIOR	host	TS
-DMARDY
HSTROBE
- DIOW	host	TS
STOP
IORDY	drive	TS	1.0 k Ω	PU
-DDMARDY
DSTROBE
CSEL	host		GND		10 k Ω	PU
- DMACK	host	TP
INTRQ	drive	TS	10 k Ω PD
- IOCS16	drive	OD	1.0 k Ω	PU	1.2 k Ω	PU
DA 0:2	host	TP
- PDIAG／-CBLID	drive	TS			10 k Ω	PU
- CS0 - CS1	host	TP
- DASP	drive	OD			10 k Ω	PU

TP = Totem Pole, TS = Tri-State, PD = Pull Down, PU = Pull-Up, OD = Open Drain

Copyright ©2000 Toshiba corporation. All rights reserved.

- 530 -

Image 30

Toshiba MK6017MAP manual Signal Treatment, Dasp

Contents

Toshiba Revised ContentsREV STGE.PER Ｓａｆｅｔｙ Usage Restrictions Safety Copyright 2000 Toshiba corporation. All rights reserved 506 Table of Contents Security SET Password Protocol Table of Figures Scope Copyright 2000 Toshiba corporation. All rights reserved 512 KEY Features Basic Specification Performance Supply Voltage Power ConsumptionPower Sequence Energy Consumption Efficiency Drive Orientation DimensionWeight Mounting Instructions Installation Screwing MK6017MAP Dimensions MK6017MAP Mounting Recommendation Vibration Temperature and HumidityTemperature Shock Acoustics （Sound Power ） Safety StandardsAltitude Mean Time to Failure Mttf Error RatePreventive Maintenance PM Product Life Load/Unload Interface Connector CablingCable Cable length and capacitance Electrical specificationDC input/output Characteristics 10.2.2.1 Input Output Interface connector ATA interface connector Dasp Ground Pin AssignmentPdiag ／-CBLID Ground Reserved Signal Treatment Dasp Signal Description Series resistance Copyright 2000 Toshiba corporation. All rights reserved 532 Host Interface Timing Program I/O Write Timing Program I/O Read Timing ATA-2 Specifications Single Word DMA Write Timing ATA-2 Specification Single Word DMA Read Timing ATA/ATAPI-5 Specifications Multiword DMA Write Timing Multiword DMA Read Timing Ultra DMA Timing Hdmardy Sustained Ultra DMA data in burst Device terminating an Ultra DMA data in burst CRC Host terminating an Ultra DMA data in burst Initiating an Ultra DMA data out burst Ddmardy Sustained Ultra DMA data out burst Host terminating an Ultra DMA data out burst Device terminating an Ultra DMA data out burst ATA/ATAPI specifications Reset Timing Grounding Address Decoding 1 Register map Register Description Security commands Error RegisterOperational Mode Disk Access command Diagnostic ModeSmart command Initialize Device Parameters command Cylinder Low Registers Smart commandsSector Number Register Cylinder High Registers Device/Head Register DEV HS3 HS2 HS1 HS0 Status Register BSY Drdy DSC3 DRQ Corr IDX ERR Command Register Command Code Device Address register4 Alternate Status RegisterDevice Control Register Srst IEN Command Descriptions Nop 00h Recalibrate5 1xhFlush Cache E7h Read Sector 20h/21h Read Long6 22h/23hWrite Sector 30h/31h Write Long7 32h/33h Read Verify 40hWrite Verify8 3Ch Format Track 50h Execute Diagnostics 90h Seek 7xhToshiba Specific Initialize Device Parameters 91h Read Multiple C4h Write Multiple C5h Set Multiple Mode C6h Read DMA C8h/C9h Write DMA CAh/CBh Idle Immediate E1/95 Power Control ExhStand-by Immediate E0/94 SC=X Idle E3/97 Check Power Mode E5/98Stand-by E2/96 Sleep E6/99 Read Buffer E4h Write Buffer E8h Identify Device ECh Word Description Hex 360014937 2 Identify Information 360014937 3 Identify Information 360014937 4 Identify Information =ATA Toshiba MK6017MAP MK6017MAP Copyright 2000 Toshiba corporation. All rights reserved 581 Copyright 2000 Toshiba corporation. All rights reserved 582 Copyright 2000 Toshiba corporation. All rights reserved 583 Timer Actual Value Copyright 2000 Toshiba corporation. All rights reserved 585 Set Max Address F9h Read Native Max Address F8h Set Features EFh Features FT register defines following selections Security SET Password F1h Security Set Password information Security Unlock F2h Security Erase Prepare F3h Security Erase Unit F4h Security Freeze Lock F5h Security Disable Password F6h Smart Function Set 10.8.33.1 Smart Read Attribute values Attribute Name Value Definition Copyright 2000 Toshiba corporation. All rights reserved 596 10.8.33.2 Smart Read Attribute thresholds Smart Enable Disable Attribute Autosave 10.8.33.4 Smart Save Attribute Values Off-line mode 10.8.33.5 Smart Execute Off-line Immediate Captive mode 10.8.33.6 Command CodeRegister Setting Normal Completion Register Command data structure Error data structure Self-test log sector Self-test index 10.8.33.7 Smart Write Log Sector Smart Enable Operations 10.8.33.9 Smart Disable Operations Smart Enable/Disable Automatic Off-line Smart Return Status Security mode default setting Initial setting of the user password Security mode operation from power-on UnlockUnit Password lost Command Table Smart function default setting AttributesAttributes values Performance Idle Adaptive Power Mode ControlLow Power Idle Active Idle Reset Register Power on Hardware Reset Software Reset Master/Slave Configuration LOWHigh Cache Memory Automatic Write ReallocationCache Operations Protocol PIO data in commands Commands for this class are PIO data out commands PIO data out protocol Non-data commands Non-data protocol DMA data transfer commands Ultra DMA Copyright 2000 Toshiba corporation. All rights reserved 624 = DD2 XOR CRCOUT13 = DD0 XOR CRCOUT15= DD1 XOR CRCOUT14 = DD3 XOR CRCOUT12 Function and Intervals Timeout Other timings