Format Track 50h | Toshiba MK6017MAP specs

360014937

sector data from the host to the media. After transferring the last data in the buffer, it sets BSY and issues an Interrupt.

10.8.10 Format Track 9				(50h)

	COMMAND CODE			0 1 0 1 0 0 0 0	REGISTER
		REGISTER SETTING			NORMAL COMPLETION
	DR		drive no.		no change
	CY	cylinder to format			no change
	HD	head to format			no change
	SN				01H
	SC				00H
	FT				no change

The track specified by the task file is formatted with ID and data fields according to the table transferred to the buffer. This command is rejected in LBA mode with an Aborted command error reported.

DRQ in status register is set as soon as the command register is written, and the buffer RAM receives the data transferred from the host. After 512 bytes are transferred into the buffer RAM, the drive resets DRQ, sets BSY and begins format operation. The drive seeks to the target cylinder if the head is not on the target track ( implied seek ). After completion of the command, it resets BSY and generates an interrupt.

Format table consists of the number of sectors ( 16 bits ) per track . Upper byte represents sector number, and lower byte represents format type.

The drive supports only 00H format type. Intending to maintain compatibility with previous models, the drive accepts any format type, but the function will not change.

Sector interleave is always set to one regardless of sector sequence in the format table. Data subsequent to format table are handled as “Don't care”.

FORMAT TABLE ( FIRST 86 BYTES ) (Ex. 43 logical sector mode)

0001, 0002, 0003, 0004, 0005, 0006, 0007, 0008, 0009, 0013, 0015, 0016, 0017, 0018,.0019, 001A,.......0029, 002A, 002B

DON’T CARE ( 426 BYTES ATTACHED )

0000, 0000, 0000, 0000, 0000, 0000, 0000, 0000, 0000, 0000, 0000, 0000, 0000, ........... 0000, 0000, 0000.

9ATA/ATAPI-4 defines this command as Vendor specific. The drive supports this command to maintain ATA-3, and the previous models compatibility. User is recommended not to use this command.

Copyright © 2000 Toshiba corporation. All rights reserved.

- 563 -

Image 63

Toshiba MK6017MAP manual Format Track 50h

Contents

Toshiba STGE.PER ContentsREV Revised Ｓａｆｅｔｙ Usage Restrictions Safety Copyright 2000 Toshiba corporation. All rights reserved 506 Table of Contents Security SET Password Protocol Table of Figures Scope Copyright 2000 Toshiba corporation. All rights reserved 512 KEY Features Basic Specification Performance Energy Consumption Efficiency Power ConsumptionPower Sequence Supply Voltage Mounting Instructions DimensionWeight Drive Orientation Screwing Installation MK6017MAP Dimensions MK6017MAP Mounting Recommendation Shock Temperature and HumidityTemperature Vibration Acoustics （Sound Power ） Safety StandardsAltitude Product Life Error RatePreventive Maintenance PM Mean Time to Failure Mttf Load/Unload Interface Connector CablingCable Output Electrical specificationDC input/output Characteristics 10.2.2.1 Input Cable length and capacitance ATA interface connector Interface connector Ground Reserved Pin AssignmentPdiag ／-CBLID Dasp Ground Dasp Signal Treatment Series resistance Signal Description Copyright 2000 Toshiba corporation. All rights reserved 532 Program I/O Write Timing Host Interface Timing Program I/O Read Timing Single Word DMA Write Timing ATA-2 Specifications Single Word DMA Read Timing ATA-2 Specification Multiword DMA Write Timing ATA/ATAPI-5 Specifications Multiword DMA Read Timing Hdmardy Ultra DMA Timing Sustained Ultra DMA data in burst CRC Device terminating an Ultra DMA data in burst Host terminating an Ultra DMA data in burst Ddmardy Initiating an Ultra DMA data out burst Sustained Ultra DMA data out burst Host terminating an Ultra DMA data out burst Device terminating an Ultra DMA data out burst ATA/ATAPI specifications Grounding Reset Timing 1 Register map Address Decoding Register Description Security commands Error RegisterOperational Mode Initialize Device Parameters command Diagnostic ModeSmart command Disk Access command Cylinder High Registers Smart commandsSector Number Register Cylinder Low Registers DEV HS3 HS2 HS1 HS0 Device/Head Register BSY Drdy DSC3 DRQ Corr IDX ERR Status Register Command Register Command Code Srst IEN Alternate Status RegisterDevice Control Register Device Address register4 Command Descriptions Nop 00h Recalibrate5 1xhFlush Cache E7h Read Sector 20h/21h Read Long6 22h/23hWrite Sector 30h/31h Write Long7 32h/33h Read Verify 40hWrite Verify8 3Ch Format Track 50h Execute Diagnostics 90h Seek 7xhToshiba Specific Initialize Device Parameters 91h Read Multiple C4h Write Multiple C5h Read DMA C8h/C9h Set Multiple Mode C6h Write DMA CAh/CBh SC=X Power Control ExhStand-by Immediate E0/94 Idle Immediate E1/95 Sleep E6/99 Check Power Mode E5/98Stand-by E2/96 Idle E3/97 Write Buffer E8h Read Buffer E4h Identify Device ECh Hex Word Description 360014937 2 Identify Information 360014937 3 Identify Information 360014937 4 Identify Information =ATA Toshiba MK6017MAP MK6017MAP Copyright 2000 Toshiba corporation. All rights reserved 581 Copyright 2000 Toshiba corporation. All rights reserved 582 Copyright 2000 Toshiba corporation. All rights reserved 583 Timer Actual Value Copyright 2000 Toshiba corporation. All rights reserved 585 Read Native Max Address F8h Set Max Address F9h Features FT register defines following selections Set Features EFh Security Set Password information Security SET Password F1h Security Erase Prepare F3h Security Unlock F2h Security Freeze Lock F5h Security Erase Unit F4h F6h Security Disable Password Smart Function Set Smart Read Attribute values 10.8.33.1 Attribute Name Value Definition Copyright 2000 Toshiba corporation. All rights reserved 596 Smart Read Attribute thresholds 10.8.33.2 10.8.33.4 Smart Save Attribute Values Smart Enable Disable Attribute Autosave 10.8.33.5 Smart Execute Off-line Immediate Off-line mode Captive mode Register Command CodeRegister Setting Normal Completion 10.8.33.6 Command data structure Error data structure Self-test log sector Self-test index 10.8.33.7 Smart Write Log Sector 10.8.33.9 Smart Disable Operations Smart Enable Operations Smart Return Status Smart Enable/Disable Automatic Off-line Initial setting of the user password Security mode default setting Security mode operation from power-on UnlockUnit Password lost Command Table Smart function default setting AttributesAttributes values Active Idle Adaptive Power Mode ControlLow Power Idle Performance Idle Register Power on Hardware Reset Software Reset Reset Master/Slave Configuration LOWHigh Cache Memory Automatic Write ReallocationCache Operations Protocol Commands for this class are PIO data in commands PIO data out protocol PIO data out commands Non-data protocol Non-data commands DMA data transfer commands Ultra DMA Copyright 2000 Toshiba corporation. All rights reserved 624 = DD3 XOR CRCOUT12 = DD0 XOR CRCOUT15= DD1 XOR CRCOUT14 = DD2 XOR CRCOUT13 Other timings Function and Intervals Timeout