Stand-by E2/96, Idle E3/97, Sleep E6/99 | Toshiba MK6017MAP instruction

360014937

10.8.20.3 Stand-by (E2/96)

When SC = 0, the drive goes into Stand-by mode and then into Idle mode. If the drive receives no access during specified time period ( see the table below ), the drive enters stand-by mode.

When SC≠0, the drive enters stand-by mode and enables auto stand-by function. The value in SC register will be converted to auto stand-by timer according to the following table.

Value in SC register	Setting
0	45 min.
1-255	(SC x 5) sec.

When the specified time period has passed, the drive enters stand-by mode. If a disk access command is received during stand-by mode, the spindle starts rotating and the drive executes read/write operation. After completing the command, the drive reset stand-by timer and the timer starts counting down.

10.8.20.4 Idle (E3/97)

When SC = 0, the drive enters Idle mode. If the drive receives no access during specified time period ( see the table below ), the drive enters stand-by mode.

When SC≠0, the drive goes into idle mode and enables auto stand-by function. The value in SC register is converted to the value of auto stand-by timer according to the following table.

Value in SC register	Setting
0	45 min.
1-255	(SC x 5) sec.

When the specified time period has expired, the drive enters the stand-by mode. If disk access command is received during the stand-by mode, the spindle starts rotating and executes read/write operation. After completing the command, The drive resets stand-by timer and the timer starts counting down.

Power on default setting is auto stand-by (timer setting:45 min.).

10.8.20.5 Check Power Mode (E5/98)

SC result value=00 indicates that the drive is in stand-by mode or going into stand-by mode or is shifting from stand-by mode into idle mode.

SC result value=FFH indicates that the drive is in idle mode.

10.8.20.6 Sleep (E6/99)

When SC=X, the drive enters sleep mode immediately. After entering the sleep mode, the drive issues an interrupt to report the host that the command has been completed. The drive recovers from sleep mode and enters stand-by mode by receiving a reset.

Copyright © 2000 Toshiba corporation. All rights reserved.

- 571 -

Image 71

Toshiba MK6017MAP manual Stand-by E2/96, Idle E3/97, Check Power Mode E5/98, Sleep E6/99

Contents

Toshiba STGE.PER ContentsREV Revised Ｓａｆｅｔｙ Usage Restrictions Safety Copyright 2000 Toshiba corporation. All rights reserved 506 Table of Contents Security SET Password Protocol Table of Figures Scope Copyright 2000 Toshiba corporation. All rights reserved 512 KEY Features Basic Specification Performance Energy Consumption Efficiency Power ConsumptionPower Sequence Supply Voltage Mounting Instructions DimensionWeight Drive Orientation Screwing Installation MK6017MAP Dimensions MK6017MAP Mounting Recommendation Shock Temperature and HumidityTemperature Vibration Altitude Acoustics （Sound Power ）Safety Standards Product Life Error RatePreventive Maintenance PM Mean Time to Failure Mttf Load/Unload Cable Interface ConnectorCabling Output Electrical specificationDC input/output Characteristics 10.2.2.1 Input Cable length and capacitance ATA interface connector Interface connector Ground Reserved Pin AssignmentPdiag ／-CBLID Dasp Ground Dasp Signal Treatment Series resistance Signal Description Copyright 2000 Toshiba corporation. All rights reserved 532 Program I/O Write Timing Host Interface Timing Program I/O Read Timing Single Word DMA Write Timing ATA-2 Specifications Single Word DMA Read Timing ATA-2 Specification Multiword DMA Write Timing ATA/ATAPI-5 Specifications Multiword DMA Read Timing Hdmardy Ultra DMA Timing Sustained Ultra DMA data in burst CRC Device terminating an Ultra DMA data in burst Host terminating an Ultra DMA data in burst Ddmardy Initiating an Ultra DMA data out burst Sustained Ultra DMA data out burst Host terminating an Ultra DMA data out burst Device terminating an Ultra DMA data out burst ATA/ATAPI specifications Grounding Reset Timing 1 Register map Address Decoding Register Description Operational Mode Security commandsError Register Initialize Device Parameters command Diagnostic ModeSmart command Disk Access command Cylinder High Registers Smart commandsSector Number Register Cylinder Low Registers DEV HS3 HS2 HS1 HS0 Device/Head Register BSY Drdy DSC3 DRQ Corr IDX ERR Status Register Command Register Command Code Srst IEN Alternate Status RegisterDevice Control Register Device Address register4 Command Descriptions Flush Cache E7h Nop 00hRecalibrate5 1xh Write Sector 30h/31h Read Sector 20h/21hRead Long6 22h/23h Write Verify8 3Ch Write Long7 32h/33hRead Verify 40h Format Track 50h Toshiba Specific Execute Diagnostics 90hSeek 7xh Initialize Device Parameters 91h Read Multiple C4h Write Multiple C5h Read DMA C8h/C9h Set Multiple Mode C6h Write DMA CAh/CBh SC=X Power Control ExhStand-by Immediate E0/94 Idle Immediate E1/95 Sleep E6/99 Check Power Mode E5/98Stand-by E2/96 Idle E3/97 Write Buffer E8h Read Buffer E4h Identify Device ECh Hex Word Description 360014937 2 Identify Information 360014937 3 Identify Information 360014937 4 Identify Information =ATA Toshiba MK6017MAP MK6017MAP Copyright 2000 Toshiba corporation. All rights reserved 581 Copyright 2000 Toshiba corporation. All rights reserved 582 Copyright 2000 Toshiba corporation. All rights reserved 583 Timer Actual Value Copyright 2000 Toshiba corporation. All rights reserved 585 Read Native Max Address F8h Set Max Address F9h Features FT register defines following selections Set Features EFh Security Set Password information Security SET Password F1h Security Erase Prepare F3h Security Unlock F2h Security Freeze Lock F5h Security Erase Unit F4h F6h Security Disable Password Smart Function Set Smart Read Attribute values 10.8.33.1 Attribute Name Value Definition Copyright 2000 Toshiba corporation. All rights reserved 596 Smart Read Attribute thresholds 10.8.33.2 10.8.33.4 Smart Save Attribute Values Smart Enable Disable Attribute Autosave 10.8.33.5 Smart Execute Off-line Immediate Off-line mode Captive mode Register Command CodeRegister Setting Normal Completion 10.8.33.6 Command data structure Error data structure Self-test log sector Self-test index 10.8.33.7 Smart Write Log Sector 10.8.33.9 Smart Disable Operations Smart Enable Operations Smart Return Status Smart Enable/Disable Automatic Off-line Initial setting of the user password Security mode default setting Unit Security mode operation from power-onUnlock Password lost Command Table Attributes values Smart function default settingAttributes Active Idle Adaptive Power Mode ControlLow Power Idle Performance Idle Register Power on Hardware Reset Software Reset Reset High Master/Slave ConfigurationLOW Cache Operations Cache MemoryAutomatic Write Reallocation Protocol Commands for this class are PIO data in commands PIO data out protocol PIO data out commands Non-data protocol Non-data commands DMA data transfer commands Ultra DMA Copyright 2000 Toshiba corporation. All rights reserved 624 = DD3 XOR CRCOUT12 = DD0 XOR CRCOUT15= DD1 XOR CRCOUT14 = DD2 XOR CRCOUT13 Other timings Function and Intervals Timeout