360014937 2 Identify Information | Toshiba MK6017MAP manual

360014937

Table 10.8-2 Identify Information (Continued)

WORD		DESCRIPTION	Hex.
57-58	Current capacity in sectors		XXXX
	(Number of current cylinders * Number of current heads * Number of current
	sectors per track)
59	15-9	Reserved	01XX
	8 1=Multiple sector setting is valid
	7-0 XXh=Current setting for number of sectors that can be transferred per
	interrupt on R/W Multiple command
60-61	Total number of user addressable sectors (LBA mode only)		[5*]
62	15-8	Single word DMA transfer mode active 11	XX07
	7-0 Single word DMA transfer mode supported 14
63	15-8	Multiword DMA transfer mode active	XX07
	7-0 Multiword DMA transfer mode supported
64	15-8	reserved	0003
	7-0 Advanced PIO Transfer Modes Supported
		bit 7-2 Reserved
		bit 1 = 1 PIO MODE 4 supported
		bit 0 = 1 PIO MODE 3 supported
65	Minimum Multiword DMA Transfer Cycle Time Per Word (ns)		0078
66	Manufacturer’s Recommended Multiword DMA Transfer Cycle Time		0078
67	Minimum PIO Transfer Cycle Time Without Flow Control (ns)		0078
68	Minimum PIO Transfer Cycle Time With IOCHRDY Flow Control		0078
69-79	Reserved (for future command overlap and queuing)		0000
80	Major version number		003E
	0000h or FFFFh = device does not report version
	15-4	Reserved for ATA-6~14
	5	1=supports ATA/ATAPI-5
	4	1=supports ATA/ATAPI-4
	3	1=supports ATA-3
	2	1=supports ATA-2
	1	1=supports ATA-1
	0	Reserved
81	Minor version number		0000
	0000h or FFFFh = device does not report version
82	Command set supported.		7C6B
	0000h or FFFFh = command set notification not supported
	15	Reserved
	14	1=NOP command supported
	13 1=READ BUFFER command supported
	12 1=WRITE BUFFER command supported
	11 1=WRITE VERIFY command supported
	10 1=Host Protected Area feature set supported
	9	1=DEVICE RESET command supported
	8	1=SERVICE interrupt supported
	7	1=release interrupt supported
	6	1=look-ahead supported
	5	1=write cache supported
	4	1=supports PACKET Command feature set
	3	1=supports power management feature set
	2	1=supports removable feature set
	1	1=supports security feature set
	0	1=supports SMART feature set

11ATA-3 defines this field as “Vendor specific (obsolete)” To maintain compatibility between ATA-2, the drive supports this field as specified in ATA-2. This field may be used for other purposes in future models.

Copyright © 2000 Toshiba corporation. All rights reserved.

- 575 -

Image 75

Toshiba MK6017MAP manual 360014937 2 Identify Information

Contents

Toshiba STGE.PER ContentsREV Revised Ｓａｆｅｔｙ Usage Restrictions Safety Copyright 2000 Toshiba corporation. All rights reserved 506 Table of Contents Security SET Password Protocol Table of Figures Scope Copyright 2000 Toshiba corporation. All rights reserved 512 KEY Features Basic Specification Performance Energy Consumption Efficiency Power ConsumptionPower Sequence Supply Voltage Mounting Instructions DimensionWeight Drive Orientation Screwing Installation MK6017MAP Dimensions MK6017MAP Mounting Recommendation Shock Temperature and HumidityTemperature Vibration Acoustics （Sound Power ） Safety StandardsAltitude Product Life Error RatePreventive Maintenance PM Mean Time to Failure Mttf Load/Unload Interface Connector CablingCable Output Electrical specificationDC input/output Characteristics 10.2.2.1 Input Cable length and capacitance ATA interface connector Interface connector Ground Reserved Pin AssignmentPdiag ／-CBLID Dasp Ground Dasp Signal Treatment Series resistance Signal Description Copyright 2000 Toshiba corporation. All rights reserved 532 Program I/O Write Timing Host Interface Timing Program I/O Read Timing Single Word DMA Write Timing ATA-2 Specifications Single Word DMA Read Timing ATA-2 Specification Multiword DMA Write Timing ATA/ATAPI-5 Specifications Multiword DMA Read Timing Hdmardy Ultra DMA Timing Sustained Ultra DMA data in burst CRC Device terminating an Ultra DMA data in burst Host terminating an Ultra DMA data in burst Ddmardy Initiating an Ultra DMA data out burst Sustained Ultra DMA data out burst Host terminating an Ultra DMA data out burst Device terminating an Ultra DMA data out burst ATA/ATAPI specifications Grounding Reset Timing 1 Register map Address Decoding Register Description Security commands Error RegisterOperational Mode Initialize Device Parameters command Diagnostic ModeSmart command Disk Access command Cylinder High Registers Smart commandsSector Number Register Cylinder Low Registers DEV HS3 HS2 HS1 HS0 Device/Head Register BSY Drdy DSC3 DRQ Corr IDX ERR Status Register Command Register Command Code Srst IEN Alternate Status RegisterDevice Control Register Device Address register4 Command Descriptions Nop 00h Recalibrate5 1xhFlush Cache E7h Read Sector 20h/21h Read Long6 22h/23hWrite Sector 30h/31h Write Long7 32h/33h Read Verify 40hWrite Verify8 3Ch Format Track 50h Execute Diagnostics 90h Seek 7xhToshiba Specific Initialize Device Parameters 91h Read Multiple C4h Write Multiple C5h Read DMA C8h/C9h Set Multiple Mode C6h Write DMA CAh/CBh SC=X Power Control ExhStand-by Immediate E0/94 Idle Immediate E1/95 Sleep E6/99 Check Power Mode E5/98Stand-by E2/96 Idle E3/97 Write Buffer E8h Read Buffer E4h Identify Device ECh Hex Word Description 360014937 2 Identify Information 360014937 3 Identify Information 360014937 4 Identify Information =ATA Toshiba MK6017MAP MK6017MAP Copyright 2000 Toshiba corporation. All rights reserved 581 Copyright 2000 Toshiba corporation. All rights reserved 582 Copyright 2000 Toshiba corporation. All rights reserved 583 Timer Actual Value Copyright 2000 Toshiba corporation. All rights reserved 585 Read Native Max Address F8h Set Max Address F9h Features FT register defines following selections Set Features EFh Security Set Password information Security SET Password F1h Security Erase Prepare F3h Security Unlock F2h Security Freeze Lock F5h Security Erase Unit F4h F6h Security Disable Password Smart Function Set Smart Read Attribute values 10.8.33.1 Attribute Name Value Definition Copyright 2000 Toshiba corporation. All rights reserved 596 Smart Read Attribute thresholds 10.8.33.2 10.8.33.4 Smart Save Attribute Values Smart Enable Disable Attribute Autosave 10.8.33.5 Smart Execute Off-line Immediate Off-line mode Captive mode Register Command CodeRegister Setting Normal Completion 10.8.33.6 Command data structure Error data structure Self-test log sector Self-test index 10.8.33.7 Smart Write Log Sector 10.8.33.9 Smart Disable Operations Smart Enable Operations Smart Return Status Smart Enable/Disable Automatic Off-line Initial setting of the user password Security mode default setting Security mode operation from power-on UnlockUnit Password lost Command Table Smart function default setting AttributesAttributes values Active Idle Adaptive Power Mode ControlLow Power Idle Performance Idle Register Power on Hardware Reset Software Reset Reset Master/Slave Configuration LOWHigh Cache Memory Automatic Write ReallocationCache Operations Protocol Commands for this class are PIO data in commands PIO data out protocol PIO data out commands Non-data protocol Non-data commands DMA data transfer commands Ultra DMA Copyright 2000 Toshiba corporation. All rights reserved 624 = DD3 XOR CRCOUT12 = DD0 XOR CRCOUT15= DD1 XOR CRCOUT14 = DD2 XOR CRCOUT13 Other timings Function and Intervals Timeout