Procedures, Startup | Toshiba TOSNIC-7000S specs

6 F 3 H 1 0 0 1

8.3Procedures

8.3.1 Startup

Table 8.1 shows the procedure used to start up the UPS.

LED status		: Unlit	: Lit	: Blinking
			Table 8.1	Startup Procedures
Step	Procedure		LCD/LED Status (After Execution)
1	Turn on the control			OPERATION GUIDANCE
	power supply switch			OPERATION GUIDANCE
	power supply switch
	(8A) on the panel.			MOVE #52C AND #52L TO ‘ON’ POSITION
				MOVE #52C AND #52L TO ‘ON’ POSITION
			～	～	～	UPS
					～	UPS
			AC INPUT	CONVERTER	INVERTER
				FLOAT CHARGE		AC	～
			BATTERIES	EQUAL CHARGE		SWITCH
				EQUAL CHARGE
				DISCHARGE			AC OUTPUT
				DISCHARGE
			～			BYPASS
			BYPASS INPUT			BYPASS
			BYPASS INPUT
				The "BYPASS" LED lit.
2	Turn on the bypass AC			BYPASS
	input 52C and the AC			BYPASS
	input 52C and the AC
	output 52L circuit			MOVE #6CH TO ‘ON’ POSITION
	breakers.			MOVE #6CH TO ‘ON’ POSITION
	(The UPS will change
	to bypass power		～	～	～	UPS
	supply status and AC				～	UPS
	supply status and AC		AC INPUT	CONVERTER	INVERTER
	output voltage will be		AC INPUT	CONVERTER	INVERTER
	output voltage will be					AC	～
	generated.)			FLOAT CHARGE		AC	～
			BATTERIES	EQUAL CHARGE		SWITCH
				EQUAL CHARGE
				DISCHARGE			AC OUTPUT
				DISCHARGE
			～			BYPASS
			BYPASS INPUT			BYPASS
			BYPASS INPUT

	The "BYPASS INPUT" and The "OUTPUT"LEDs lit.
3	Turn on the precharge	BYPASS
	circuit switch (6CH)*.	BYPASS
	circuit switch (6CH)*.
			WAIT FOR A WHILE
	～	～	～	UPS
			～	UPS
	AC INPUT	CONVERTER	INVERTER
		FLOAT CHARGE		AC	～
				AC	～
	BATTERIES	EQUAL CHARGE		SWITCH
		EQUAL CHARGE
					AC OUTPUT
		DISCHARGE			AC OUTPUT
		DISCHARGE
	～			BYPASS
				BYPASS

BYPASS INPUT

*The control power supply switch 8A is left in the on state (Do not turn this switch off.)

-27 -

Image 28

Toshiba TOSNIC-7000S instruction manual Procedures, Startup

Contents

3 H 1 0 0 JulyALL Rights Reserved Vent type stand-alone lead storage battery Sealed stand-alone lead storage batteryProcedure and the status of the UPS unit Synchronized mode Introduction Safety PrecautionsExact nature of what must be done is indicated 3 H 1 0 0 Safety Precautions Use Cards Do not open the rear door Accordance with customer stipulations Be always Do not turn off Turn on Running Locations of the Warning Labels Example 300 kVADo not touch rotating section Handling Precautions 3 H 1 0 0 Handling Precautions 3 H 1 0 0 Handling Precautions Contents Appearance Example 300 kVA Controls and Circuit Configuration Panel ControlsExample 300 kVA C52R D72B E52R F52M G52L H8A I6CH This may result in failure Circuit Configuration Fault UPS Key-switch Function Name Remarks 3 H 1 0 0 Panel Key-switchPanel Keys Key Functions For HS or AHH individual battery systems Name Function Remarks Panels Graphic Display Panel 2 Graphic Display Panel Control This LED lights up when the UPS is operating This LED lights up when the AC input circuit breakerThis LED is unlit when the converter has stopped Operating. It blinks when the converter is starting up LCD Display Scroll up Scroll down 3 H 1 0 0 Normal Display Screen Normal Display Screen LCD Screen Description200V 50 % Normal Display Screen 60.0HzBYP I/P-V 401V 3 H 1 0 0 Failure Display Screen Failure Display Screen LCD Screen Description52R Trip 98-09-09 3 H 1 0 0 LCD Screen Switching Operation Types of Operation Pre-operational checkOperation General Description/Objective Startup Starts up and operates the stopped UPS Procedures Startup When the message Appears, turn on Bypass Press ‘RUN’ SwitchMain circuit AC input Circuit breaker 52R Bypass Move #52R to ‘ON’ Position On page 14 for at least Second Wait several seconds For the startup processTo finish Main circuit DC input → The will start Power supply Changing process UPS power supplyHold down the UPS Key g in the Figure On page14 for at 3 H 1 0 0 Switch Power Supply UPS → Bypass 3 H 1 0 0 3 H 1 0 0 Stop Stop Breaker72B Restart Press ‘RUN’ Switch Shutdown Move #52R to ‘OFF’Batteries LED unlit → This complete UPS Shutdown 3 H 1 0 0 Complete Shutdown Complete Shutdown Circuit switch 6CH Using the scroll keysTurn off the precharge Wait about 20 minutes Until the DC capacitor Changing From Floating Charge to Equalized Charge Changing From Equalized Charge to Floating Charge Check to make sure That the EqualSecond → Change to floating Charge is complete Float Charge LED lit Equal Charge LED unlit Changing from Protective Charge to Floating Charge 3 H 1 0 0 Changing the Power Supply to Maintenance Bypass Changing From UPS to maintenance Bypass Power Supply Changing From Maintenance Bypass to UPS Power Supply Same as steps 1-41 Startup 52R 72B 52C 52M 52L Types of Errors TroubleshootingName Description LCD Failure Displays Failure Data Screen52R Trip 98-09-09 Failure Data Screen Descriptions Up to 10 screens of warning data can be displayed Shows the nature of the warning. For details, see Section↑ indicates there is a warning screen before this screen ↓ indicates there is a warning screen after this screen 3 H 1 0 0 Failure Messages Protective Detector Locations Fault Trip LCD Message Description Indication Bypass input frequency error Including operation errorBattery temperature has risen Battery fluid level has gone below prescribed level For Individual battery systems. For HS or AHH batteries Position of Scroll Keys in Failure Data Screens Scrolls to the previous screen see Figure Scroll KeysScrolls to the next screen see Figure Procedure Saving Waveforms Only open the front panel when performing necessary Restoring UPS Operation 11 Restoring UPS Operation Example Also check for otherFailure Data screens 98-09-09 By scrolling with scroll Panel