Restoring UPS Operation | Toshiba TOSNIC-7000S specification

6 F 3 H 1 0 0 1

9.4Restoring UPS Operation

Contact the Toshiba Service Center in the event of malfunction or failure.

This unit should be repaired only by authorized Toshiba service personnel. Servicing by untrained personnel may increase the scale of the failure or result in electric shock or injury.

Do not attempt to modify or move the unit yourself or to have this done by a third party.

Electric shock, injury or failure may result if persons other than specially trained Toshiba technicians attempt to modify or move the unit. Be sure to contact Toshiba if you wish modifications to be made or if you wish to move the unit.

Only open the front panel when performing necessary

WARNING operations.*

Operating parts and high-voltage areas inside the UPS have been provided with covers as a safety precaution. Still, touching areas other than those that must be touched to perform necessary operations may result in electric shock, burns or other injuries.

*In this case, "necessary operations" means operating circuit breakers/auxiliary switches and inserting/removing memory cards.

Do not open the rear door.

The parts inside carry high voltage. Touching them may result in electric shock, burns or failure.

This section describes the procedure used to restore UPS operation. Table 9.11 shows an example in which the UPS is restored after a trip error has occurred on circuit breaker 52R with the message "52R TRIP."

- 51 -

Image 52

Toshiba TOSNIC-7000S instruction manual Restoring UPS Operation, Only open the front panel when performing necessary

Contents

3 H 1 0 0 JulyALL Rights Reserved Vent type stand-alone lead storage battery Sealed stand-alone lead storage batteryProcedure and the status of the UPS unit Synchronized mode Introduction Safety PrecautionsExact nature of what must be done is indicated 3 H 1 0 0 Safety Precautions Use Cards Do not open the rear door Accordance with customer stipulations Be always Do not turn off Turn on Running Locations of the Warning Labels Example 300 kVADo not touch rotating section Handling Precautions 3 H 1 0 0 Handling Precautions 3 H 1 0 0 Handling Precautions Contents Appearance Example 300 kVA Controls and Circuit Configuration Panel ControlsExample 300 kVA C52R D72B E52R F52M G52L H8A I6CH This may result in failure Circuit Configuration Fault UPS Key-switch Function Name Remarks 3 H 1 0 0 Panel Key-switchPanel Keys Key Functions For HS or AHH individual battery systems Name Function Remarks Panels Graphic Display Panel 2 Graphic Display Panel Control This LED lights up when the UPS is operating This LED lights up when the AC input circuit breakerThis LED is unlit when the converter has stopped Operating. It blinks when the converter is starting up LCD Display Scroll up Scroll down 3 H 1 0 0 Normal Display Screen Normal Display Screen LCD Screen Description200V 50 % Normal Display Screen 60.0HzBYP I/P-V 401V 3 H 1 0 0 Failure Display Screen Failure Display Screen LCD Screen Description52R Trip 98-09-09 3 H 1 0 0 LCD Screen Switching Operation Types of Operation Pre-operational checkOperation General Description/Objective Startup Starts up and operates the stopped UPS Procedures Startup When the message Appears, turn on Bypass Press ‘RUN’ SwitchMain circuit AC input Circuit breaker 52R Bypass Move #52R to ‘ON’ Position On page 14 for at least Second Wait several seconds For the startup processTo finish Main circuit DC input → The will start Power supply Changing process UPS power supplyHold down the UPS Key g in the Figure On page14 for at 3 H 1 0 0 Switch Power Supply UPS → Bypass 3 H 1 0 0 3 H 1 0 0 Stop Stop Breaker72B Restart Press ‘RUN’ Switch Shutdown Move #52R to ‘OFF’Batteries LED unlit → This complete UPS Shutdown 3 H 1 0 0 Complete Shutdown Complete Shutdown Circuit switch 6CH Using the scroll keysTurn off the precharge Wait about 20 minutes Until the DC capacitor Changing From Floating Charge to Equalized Charge Changing From Equalized Charge to Floating Charge Check to make sure That the EqualSecond → Change to floating Charge is complete Float Charge LED lit Equal Charge LED unlit Changing from Protective Charge to Floating Charge 3 H 1 0 0 Changing the Power Supply to Maintenance Bypass Changing From UPS to maintenance Bypass Power Supply Changing From Maintenance Bypass to UPS Power Supply Same as steps 1-41 Startup 52R 72B 52C 52M 52L Types of Errors TroubleshootingName Description LCD Failure Displays Failure Data Screen52R Trip 98-09-09 Failure Data Screen Descriptions Up to 10 screens of warning data can be displayed Shows the nature of the warning. For details, see Section↑ indicates there is a warning screen before this screen ↓ indicates there is a warning screen after this screen 3 H 1 0 0 Failure Messages Protective Detector Locations Fault Trip LCD Message Description Indication Bypass input frequency error Including operation errorBattery temperature has risen Battery fluid level has gone below prescribed level For Individual battery systems. For HS or AHH batteries Position of Scroll Keys in Failure Data Screens Scrolls to the previous screen see Figure Scroll KeysScrolls to the next screen see Figure Procedure Saving Waveforms Only open the front panel when performing necessary Restoring UPS Operation 11 Restoring UPS Operation Example Also check for otherFailure Data screens 98-09-09 By scrolling with scroll Panel