3 H 1 0 0 Complete Shutdown | Toshiba TOSNIC-7000S instruction

6 F 3 H 1 0 0 1

8.3.4 Complete Shutdown

This section describes the procedure used to turn off the control power source and shut down the UPS completely (to turn everything up to the control power source off).

		Table 8.4	Complete Shutdown
Step	Procedure	LCD/LED Status (After Execution)
1-4 Same as steps 1-4 in Section 8.3.3 "Stop."
5	When the message		BYPASS
	appears, turn off the		BYPASS
	main circuit AC input
	circuit breaker (52R).		MOVE #52C AND #52L TO ‘ON’ POSITION
		～	～	～	UPS
				～	UPS
		AC INPUT	CONVERTER	INVERTER
			FLOAT CHARGE		AC	～
		BATTERIES	EQUAL CHARGE		SWITCH
			EQUAL CHARGE
			DISCHARGE			AC OUTPUT
			DISCHARGE
		～			BYPASS
		BYPASS INPUT			BYPASS
		BYPASS INPUT
			The "AC INPUT" LED unlit.
6	Turn off the AC output
	circuit breaker (52L).		OPERATION GUIDANCE
			MOVE #52C TO ‘OFF’ POSITION
		～	～	～	UPS
				～	UPS
		AC INPUT	CONVERTER	INVERTER
			FLOAT CHARGE		AC	～
			FLOAT CHARGE
		BATTERIES	EQUAL CHARGE		SWITCH
			DISCHARGE			AC OUTPUT
		～			BYPASS
		BYPASS INPUT			BYPASS
		BYPASS INPUT
			The "AC INPUT" LED unlit.
7	Turn off the Bypass		OPERATION GUIDANCE
	input circuit breaker		OPERATION GUIDANCE
	(52C).		MOVE #6CH TO ‘OFF’ POSITION
			WAIT ABOUT 20 MINUTES
			MOVE #8A TO ‘OFF’ POSITION
		～	～	～	UPS
				～	UPS
		AC INPUT	CONVERTER	INVERTER
			FLOAT CHARGE		AC	～
			FLOAT CHARGE
		BATTERIES	EQUAL CHARGE		SWITCH
			DISCHARGE			AC OUTPUT
			DISCHARGE
		～			BYPASS
		BYPASS INPUT			BYPASS
		BYPASS INPUT
			The "BYPASS INPUT" LED unlit.

- 35 -

Image 36

Toshiba TOSNIC-7000S instruction manual 3 H 1 0 0 Complete Shutdown

Contents

July 3 H 1 0 0ALL Rights Reserved Vent type stand-alone lead storage battery Sealed stand-alone lead storage batteryProcedure and the status of the UPS unit Synchronized mode Safety Precautions IntroductionExact nature of what must be done is indicated 3 H 1 0 0 Safety Precautions Use Cards Do not open the rear door Accordance with customer stipulations Locations of the Warning Labels Example 300 kVA Be always Do not turn off Turn on RunningDo not touch rotating section Handling Precautions 3 H 1 0 0 Handling Precautions 3 H 1 0 0 Handling Precautions Contents Appearance Example 300 kVA Controls and Circuit Configuration Panel ControlsExample 300 kVA C52R D72B E52R F52M G52L H8A I6CH This may result in failure Circuit Configuration Fault UPS 3 H 1 0 0 Panel Key-switch Key-switch Function Name RemarksPanel Keys Key Functions For HS or AHH individual battery systems Name Function Remarks Panels Graphic Display Panel 2 Graphic Display Panel Control This LED lights up when the UPS is operating This LED lights up when the AC input circuit breakerThis LED is unlit when the converter has stopped Operating. It blinks when the converter is starting up LCD Display Scroll up Scroll down 3 H 1 0 0 Normal Display Screen Normal Display Screen LCD Screen Description200V 50 % Normal Display Screen 60.0HzBYP I/P-V 401V 3 H 1 0 0 Failure Display Screen Failure Display Screen LCD Screen Description52R Trip 98-09-09 3 H 1 0 0 LCD Screen Switching Operation Types of Operation Pre-operational checkOperation General Description/Objective Startup Starts up and operates the stopped UPS Procedures Startup When the message Appears, turn on Bypass Press ‘RUN’ SwitchMain circuit AC input Circuit breaker 52R Bypass Move #52R to ‘ON’ Position On page 14 for at least Second Wait several seconds For the startup processTo finish Main circuit DC input → The will start Power supply Changing process UPS power supplyHold down the UPS Key g in the Figure On page14 for at 3 H 1 0 0 Switch Power Supply UPS → Bypass 3 H 1 0 0 3 H 1 0 0 Stop Stop Restart Press ‘RUN’ Switch Shutdown Move #52R to ‘OFF’ Breaker72BBatteries LED unlit → This complete UPS Shutdown 3 H 1 0 0 Complete Shutdown Complete Shutdown Circuit switch 6CH Using the scroll keysTurn off the precharge Wait about 20 minutes Until the DC capacitor Changing From Floating Charge to Equalized Charge Changing From Equalized Charge to Floating Charge Check to make sure That the EqualSecond → Change to floating Charge is complete Float Charge LED lit Equal Charge LED unlit Changing from Protective Charge to Floating Charge 3 H 1 0 0 Changing the Power Supply to Maintenance Bypass Changing From UPS to maintenance Bypass Power Supply Changing From Maintenance Bypass to UPS Power Supply Same as steps 1-41 Startup 52R 72B 52C 52M 52L Troubleshooting Types of ErrorsName Description LCD Failure Displays Failure Data Screen52R Trip 98-09-09 Failure Data Screen Descriptions Up to 10 screens of warning data can be displayed Shows the nature of the warning. For details, see Section↑ indicates there is a warning screen before this screen ↓ indicates there is a warning screen after this screen 3 H 1 0 0 Failure Messages Protective Detector Locations Fault Trip LCD Message Description Indication Bypass input frequency error Including operation errorBattery temperature has risen Battery fluid level has gone below prescribed level For Individual battery systems. For HS or AHH batteries Position of Scroll Keys in Failure Data Screens Scroll Keys Scrolls to the previous screen see FigureScrolls to the next screen see Figure Procedure Saving Waveforms Only open the front panel when performing necessary Restoring UPS Operation 11 Restoring UPS Operation Example Also check for otherFailure Data screens 98-09-09 By scrolling with scroll Panel