Toshiba TOSNIC-7000S manual

6 F 3 H 1 0 0 1

8.3.6 Changing to Floating Charge etc. (for MSE individual battery)

Table 8.7 shows the procedure used to change manually from protective charge to floating charge.

This operation does not apply to shared battery systems.

(1)An MSE battery normally operate in floating charge mode.

(2)To prevent the battery temperature from rising, the mode changes automatically to protective charge mode when a "BATT FAULT1" (BATTERY OVER TEMP.) warning occurs.

(3)In protective charge mode, the battery is automatically charged at a voltage about 5% lower than normal (floating) charge when the battery temperature has risen above the rated value, in order to prevent deterioration caused by excessive charging at high temperatures.

(4)After a set amount of time has elapsed (about 6 hours), if the "BATT FAULT1" (BATTERY OVER TEMP.) warning message has disappeared, the mode will automatically change back to floating charge. As a result, it will not normally be necessary to change the mode manually as described below.

Table 8.7 Changing from Protective Charge to Floating Charge

Step	Procedure	LCD/LED Status (After Execution)
1	Check to make sure
	that the		UPS SUPPLY
	"PROTECTION" LED		AC-VO	200[V]
	is lit..		AC-VO	200[V]
	is lit..		AC- I O	50[%]
			AC- I O	50[%]
		～	～	～	UPS
				～	UPS
2	Check to make sure	AC INPUT	CONVERTER	INVERTER
2	Check to make sure
	that the "BATT FAULT1"		FLOAT CHARGE		AC	～
			FLOAT CHARGE
	warning message has	BATTERIES	PROTECTION		SWITCH	AC OUTPUT
			PROTECTION
	disappeared.		DISCHARGE
	disappeared.
		～			BYPASS
		BYPASS INPUT			BYPASS
		BYPASS INPUT
3	Hold down the
	"FLOAT" key (h in		UPS SUPPLY
	Figure 6.3.1 on page		AC-VO	200[V]
	14) for at least 0.5		AC-VO	200[V]
	14) for at least 0.5		AC- I O	50[%]
	second.		AC- I O	50[%]
	second.
	→ Change to floating
	charge is complete.	～	～	～	UPS
	charge is complete.			～	UPS
		AC INPUT	CONVERTER	INVERTER
			FLOAT CHARGE		AC	～
			FLOAT CHARGE
		BATTERIES	PROTECTION		SWITCH
			PROTECTION
			DISCHARGE			AC OUTPUT
			DISCHARGE
		～			BYPASS
		BYPASS INPUT			BYPASS
		BYPASS INPUT
			The "FLOAT CHARGE" LED lit.
			The "PROTECTION" LED unlit.

- 39 -

Image 40

Toshiba TOSNIC-7000S instruction manual Changing from Protective Charge to Floating Charge

Contents

3 H 1 0 0 JulyALL Rights Reserved Vent type stand-alone lead storage battery Sealed stand-alone lead storage batteryProcedure and the status of the UPS unit Synchronized mode Introduction Safety PrecautionsExact nature of what must be done is indicated 3 H 1 0 0 Safety Precautions Use Cards Do not open the rear door Accordance with customer stipulations Be always Do not turn off Turn on Running Locations of the Warning Labels Example 300 kVADo not touch rotating section Handling Precautions 3 H 1 0 0 Handling Precautions 3 H 1 0 0 Handling Precautions Contents Appearance Example 300 kVA Controls and Circuit Configuration Panel ControlsExample 300 kVA C52R D72B E52R F52M G52L H8A I6CH This may result in failure Circuit Configuration Fault UPS Key-switch Function Name Remarks 3 H 1 0 0 Panel Key-switchPanel Keys Key Functions For HS or AHH individual battery systems Name Function Remarks Panels Graphic Display Panel 2 Graphic Display Panel Control This LED lights up when the UPS is operating This LED lights up when the AC input circuit breakerThis LED is unlit when the converter has stopped Operating. It blinks when the converter is starting up LCD Display Scroll up Scroll down 3 H 1 0 0 Normal Display Screen Normal Display Screen LCD Screen Description200V 50 % Normal Display Screen 60.0HzBYP I/P-V 401V 3 H 1 0 0 Failure Display Screen Failure Display Screen LCD Screen Description52R Trip 98-09-09 3 H 1 0 0 LCD Screen Switching Operation Types of Operation Pre-operational checkOperation General Description/Objective Startup Starts up and operates the stopped UPS Procedures Startup When the message Appears, turn on Bypass Press ‘RUN’ SwitchMain circuit AC input Circuit breaker 52R Bypass Move #52R to ‘ON’ Position On page 14 for at least Second Wait several seconds For the startup processTo finish Main circuit DC input → The will start Power supply Changing process UPS power supplyHold down the UPS Key g in the Figure On page14 for at 3 H 1 0 0 Switch Power Supply UPS → Bypass 3 H 1 0 0 3 H 1 0 0 Stop Stop Breaker72B Restart Press ‘RUN’ Switch Shutdown Move #52R to ‘OFF’Batteries LED unlit → This complete UPS Shutdown 3 H 1 0 0 Complete Shutdown Complete Shutdown Circuit switch 6CH Using the scroll keysTurn off the precharge Wait about 20 minutes Until the DC capacitor Changing From Floating Charge to Equalized Charge Changing From Equalized Charge to Floating Charge Check to make sure That the EqualSecond → Change to floating Charge is complete Float Charge LED lit Equal Charge LED unlit Changing from Protective Charge to Floating Charge 3 H 1 0 0 Changing the Power Supply to Maintenance Bypass Changing From UPS to maintenance Bypass Power Supply Changing From Maintenance Bypass to UPS Power Supply Same as steps 1-41 Startup 52R 72B 52C 52M 52L Types of Errors TroubleshootingName Description LCD Failure Displays Failure Data Screen52R Trip 98-09-09 Failure Data Screen Descriptions Up to 10 screens of warning data can be displayed Shows the nature of the warning. For details, see Section↑ indicates there is a warning screen before this screen ↓ indicates there is a warning screen after this screen 3 H 1 0 0 Failure Messages Protective Detector Locations Fault Trip LCD Message Description Indication Bypass input frequency error Including operation errorBattery temperature has risen Battery fluid level has gone below prescribed level For Individual battery systems. For HS or AHH batteries Position of Scroll Keys in Failure Data Screens Scrolls to the previous screen see Figure Scroll KeysScrolls to the next screen see Figure Procedure Saving Waveforms Only open the front panel when performing necessary Restoring UPS Operation 11 Restoring UPS Operation Example Also check for otherFailure Data screens 98-09-09 By scrolling with scroll Panel