Toshiba TOSNIC-7000S instruction

6 F 3 H 1 0 0 1

8.3.7 Changing the Power Supply to Maintenance Bypass

This UPS must be completely shut down when performing maintenance and inspections. In such cases, the power supply to the load will go through the maintenance bypass. Table 8.8 shows the procedure used to change the power supply to this maintenance bypass. Table 8.9 shows how to change the power supply from the maintenance bypass back to the UPS.

Table 8.8 Changing From UPS to maintenance Bypass Power Supply

Step	Procedure	LCD/LED Status (After Execution)
1-3 Same as steps 1-5 in Section 8.3.4 "Stop."
4	Turn ON maintenance		BYPASS
	bypass AC circuit		BYPASS
	breaker 52M. ,*
			MOVE #52C AND #52L TO ‘ON’
		～	～	～	UPS
				～	UPS
		AC INPUT	CONVERTER	INVERTER
			FLOAT CHARGE		AC	～
			FLOAT CHARGE
		BATTERIES	EQUAL CHARGE		SWITCH
			DISCHARGE			AC OUTPUT
			DISCHARGE
		～			BYPASS
		BYPASS INPUT			BYPASS
		BYPASS INPUT

	52R	72B	52C	52M	52L
MCCB	OFF	OFF	ON	ON	ON

5	Perform steps 6	When the UPS is shutdown completely, nothing at all will be
	through 11 in Table 8.4 displayed on the LCD screen and all LEDs will be unlit.
	“Complete Shutdown”
	on page 34 to shut		52R	72B	52C	52M	52L
	down the UPS		52R	72B	52C	52M	52L
	completely.	MCCB	OFF	OFF	OFF	ON	OFF
	→Change to	MCCB	OFF	OFF	OFF	ON	OFF
	→Change to
	maintenance bypass
	power supply
	complete.

*During load operation, always operate the circuit breakers in the following order : 52M ON→52lL OFF→ 52C OFF

**When power is supplied to the UPS, circuit breaker 52M cannot be turned on.

- 40 -

Image 41

Toshiba TOSNIC-7000S instruction manual 3 H 1 0 0 Changing the Power Supply to Maintenance Bypass

Contents

ALL Rights Reserved July3 H 1 0 0 Sealed stand-alone lead storage battery Vent type stand-alone lead storage batteryProcedure and the status of the UPS unit Synchronized mode Exact nature of what must be done is indicated Safety PrecautionsIntroduction Use 3 H 1 0 0 Safety Precautions Cards Accordance with customer stipulations Do not open the rear door Do not touch rotating section Locations of the Warning Labels Example 300 kVABe always Do not turn off Turn on Running Handling Precautions 3 H 1 0 0 Handling Precautions 3 H 1 0 0 Handling Precautions Contents Example 300 kVA Appearance Panel Controls Controls and Circuit ConfigurationExample 300 kVA C52R D72B E52R F52M G52L H8A I6CH This may result in failure Circuit Configuration UPS Fault Panel Keys 3 H 1 0 0 Panel Key-switchKey-switch Function Name Remarks Name Function Remarks Key Functions For HS or AHH individual battery systems Graphic Display Panel Panels 2 Graphic Display Panel Control This LED lights up when the AC input circuit breaker This LED lights up when the UPS is operatingThis LED is unlit when the converter has stopped Operating. It blinks when the converter is starting up Scroll up Scroll down LCD Display Normal Display Screen LCD Screen Description 3 H 1 0 0 Normal Display Screen200V 50 % 60.0Hz Normal Display ScreenBYP I/P-V 401V Failure Display Screen LCD Screen Description 3 H 1 0 0 Failure Display Screen52R Trip 98-09-09 3 H 1 0 0 LCD Screen Switching Operation Pre-operational check Types of OperationOperation General Description/Objective Startup Starts up and operates the stopped UPS Startup Procedures Bypass Press ‘RUN’ Switch When the message Appears, turn onMain circuit AC input Circuit breaker 52R Bypass Move #52R to ‘ON’ Position Wait several seconds For the startup process On page 14 for at least SecondTo finish Main circuit DC input UPS power supply → The will start Power supply Changing processHold down the UPS Key g in the Figure On page14 for at 3 H 1 0 0 Switch Power Supply UPS → Bypass 3 H 1 0 0 Stop 3 H 1 0 0 Stop Batteries LED unlit → This complete UPS Shutdown Restart Press ‘RUN’ Switch Shutdown Move #52R to ‘OFF’Breaker72B Complete Shutdown 3 H 1 0 0 Complete Shutdown Using the scroll keys Circuit switch 6CHTurn off the precharge Wait about 20 minutes Until the DC capacitor Changing From Floating Charge to Equalized Charge Check to make sure That the Equal Changing From Equalized Charge to Floating ChargeSecond → Change to floating Charge is complete Float Charge LED lit Equal Charge LED unlit Changing from Protective Charge to Floating Charge Changing From UPS to maintenance Bypass Power Supply 3 H 1 0 0 Changing the Power Supply to Maintenance Bypass Same as steps 1-4 Changing From Maintenance Bypass to UPS Power Supply1 Startup 52R 72B 52C 52M 52L Name Description TroubleshootingTypes of Errors Failure Data Screen LCD Failure Displays52R Trip 98-09-09 Failure Data Screen Descriptions Shows the nature of the warning. For details, see Section Up to 10 screens of warning data can be displayed↑ indicates there is a warning screen before this screen ↓ indicates there is a warning screen after this screen Protective Detector Locations 3 H 1 0 0 Failure Messages LCD Message Description Indication Fault Trip Including operation error Bypass input frequency errorBattery temperature has risen Battery fluid level has gone below prescribed level Position of Scroll Keys in Failure Data Screens For Individual battery systems. For HS or AHH batteries Scrolls to the next screen see Figure Scroll KeysScrolls to the previous screen see Figure Saving Waveforms Procedure Restoring UPS Operation Only open the front panel when performing necessary Also check for other 11 Restoring UPS Operation ExampleFailure Data screens 98-09-09 By scrolling with scroll Panel