Manuals / Tyco / Household Appliance / Smoke Alarm

Tyco installation manual Appendix H 4100U Specifications

Models: 4100U

1 180

Download 180 pages 17.54 Kb

Page 174

Appendix H

General

Fuses

Firmware Features

Appendix H

4100U Specifications

System Capacity	2,000 points of addressable points, plus 2,000 points of
annunciation. Expansion	Up to capacity above.
	Up to 119 Addressable cards
Cabinet Size	Dependent on system configuration
Cabinet Material	1.6mm Zintex
Cabinet Finish	Powder coated
Cabinet Colour	Cream Wrinkle
Mounting	Wall mount
Mains Input	240V AC, +6%, -10%, 50Hz
Internal Power Supply	24V DC @ 9A
Standby Battery	24V sealed lead acid up 110Ah
Battery Charger	27.3V DC (nominal)
PSU Supervision	Charger high/low, Battery low/fail
Temperature	-5°C to 45°C
Humidity	10% to 90% RH non-condensing

Refer to Table 6-1, 6-2 for full SPS specifications.

Alarm Relay Card

F1 Alarm, 3A, 15 x 5mm, Glass Cartridge

F2 Supervisory, 3A, 15 x 5mm, Glass Cartridge

F3 Trouble, 3A, 15 x 5mm, Glass Cartridge

Fused Distribution Board (if fitted)

F1 24V Out, 1A 20 x 5mm Glass Cartridge

F2 24V Out, 1A 20 x 5mm Glass Cartridge

F3 24V Out, 1A 20 x 5mm Glass Cartridge

F4 24V Out, 1A 20 x 5mm Glass Cartridge

•WALK TEST System Test

•4 Operator Access Levels

•Event Historical Logging

•Device selectable Alarm Verification

•Individual Zone Isolate

•Addressable device disable/enable

•Non-volatile Flash EPROM for field editable program changes

•Expansion cards firmware upgraded via download to flash EPROMs

H-1

Image 174

Tyco installation manual Appendix H 4100U Specifications

Contents

Installation 4100U Fire Indicator PanelFire Alarm System, Installation & Maintenance AustralianPage Manufacture Copyrights and TrademarksApprovals Product / SiteNon-DisclosureAgreement End User Liability DisclaimerModel Number & Firmware Revision DocumentAmendment Log Cautions, Warnings, and Regulatory Information Table of Contents Overview Chapter 2 Installing 4100U FACP Components4100U PIDs Assemblies, Cards & & ModulesNon-4100U Chapter 3 Installing 4100 MINIPLEX ComponentsChapter 4 Installing 4100U MINIPLEX Components 3-29Chapter 5 Networking Chapter 7 SPS Field Wiring 4100U Chapter 8 Installing 4100U IDNet & 4100MXP Cards Chapter 9 PC Software Connections Chapter 11 Installation Checklist, Commissioning& Maintenance Chapter 10 Australian Version SpecificsAppendix A The Device Configuration DIP Switch Appendix G Compatible Batteries List of Figures List of Tables Page Topic Introduction to the 4100U Fire Alarm SystemChapter See Page #System Configurations Standalone Configuration Figure 1-1.Standalone 4100U SystemMINIPLEX Configuration Continued on next pageMINIPLEX Configuration, Continued Figure 1-2.MINIPLEX 4100U SystemNetwork Configuration Figure 1-3.Hub/Ring ConfigurationContinued on next page Network Configuration, Continued Figure 1-4.Interconnected Loop Configuration4100 PIDs Non-4100U Empty cabinets with Doors Cream Wrinkle 4100U Cabinet Part Identification Numbers PIDs4100U PIDs Number of bays4100U PIDs, Continued Chapter Installing 4100U FACP Components TopicSee Page # Introduction to FACPs 4100U Continued on next pageOverview CPU Bay Introduction to FACPs 4100U, Continued Figure 2-1.Master CPU MotherboardContinued on next page BATTERY BACKUP SERVICE MODEMCONNECTOR P4 Introduction to FACPs 4100U, ContinuedContinued on next page Introduction to FACPs 4100U, ContinuedTable 2-1.Master Controller LEDs 1 through Master Controller Daughter Card LEDsContinued on next page Introduction to FACPs 4100U, ContinuedFigure 2-3.Operator Interface Operator Interface Additional CPU Bay ModulesIntroduction to FACPs 4100U, Continued Figure 2-4.System Power SupplySystem Power Supply SPS Continued on next pageFigure 2-5.The Power Distribution Interface PDI Introduction to FACPs 4100U, Continued← Mounting Bracket Step 1. Mounting Cabinets 4100UStep 2. Mounting Card Bays to Cabinets 4100U ← Bay FrontStep 3. Configuring Cards 4100U Continued on next pageStep 3. Configuring Cards 4100U, Continued Step 4. Interconnecting Modules and BaysContinued on next page Card Interconnections in the CPU Bay Card Continued on next page2-12 Interconnections Within Expansion BaysContinued on next page Connecting to MotherboardsFigure 2-7. Bay-to-BayInterconnections Basic Bay-To-BayInterconnections continuedConnector with White Wire Goes to P3 Connecting to Motherboards continuedConnector with Blue Wire Goes to P2 733-525HarnessFigure 2-9.Expansion Bay 4”x 5” Card Placement Continued on next page2-15 Figure 2-10.Expansion Bay Motherboard Placement Continued on next pageon P1 or leftmost pin connector are removed Figure 2-11.Mixed Module PlacementPlacement Continued on next pageFigure 2-12.Slave Card/PDI Connection Continued on next pagedirectly of modules are as follows Figure 2-15.LED/Switch Controller ContinuedFigure 2-14.LED/Switch Modules Continued on next pageContinued occursContinued on next page Continued Figure 2-16.LED/Switch Card MountingLED/Switch Modules Continued on next pageContinued Figure 2-17.Controller Card MountingContinued on next page Continued on next page Interconnecting CardsContinued Changing Display Card LEDs, continuedFigure 2-19.LED/Switch Controller Wiring ContinuedThe Terminal Block Utility Module 4100U Overview Mounting to the Electronics BayPage Topic Installing 4100 MINIPLEX Components Non-4100UChapter See Page #Introduction to MINIPLEX Systems Non-4100U NotesContinued Figure 3-1.MINIPLEX System DesignOverview Seventh floorMINIPLEX System Components Non-4100U Figure 3-2.The Remote Unit Interface CardContinued on next page MINIPLEX System Components Non-4100U, Continued Figure 3-3.The RIC II CardMINIPLEX System Guidelines Non-4100U Installing Modules into Cabinets Non-4100U Continued on next pageInstalling the RIC II Motherboard Continued on next page3-36 Connecting the 733-525Harness Continued on next page565-233 POWER4100 733-672HarnessMINIPLEX Wiring Non-4100U Continued on next pageMINIPLEX Wiring Non-4100U, Continued Figure 3-7.MINIPLEX Wiring NotesChapter Installing 4100U MINIPLEX Components TopicSee Page # Introduction to MINIPLEX Transponders 4100U Continued on next pageNot currently available in Australia Continued on next pageThe Local Mode TIC Figure 4-1.Transponder Interface Cards 4100-0622DIGITALAUDIO RISER Continued on next pageLocal mode is supported by the following Continued on next pageTable 5-1.TIC Specifications Electrical SpecificationsEnvironmental Specifications MINIPLEX System Guidelines 4100U Configuring Cards 4100U TIC/Riser Mounting 4100U Figure 4-2.TIC MountingContinued on next page TIC/Motherboard Interconnections 4100U Figure 4-3.Transponder Cabinet InterconnectionsPDI Jumpers Figure 4-4.The Ferrite Bead RUI Wiring 4100UFigure 4-5.TIC Wiring to the Host Panel Continued on next pagePage Chapter Networking TopicSee Page # Getting Started most secure and fault-tolerantwiring possible Figure 5-1. 4100-6014Network Interface Card Continued on next pageFigure 5-2.UT Motherboard with City Connection Figure 5-3.UT Motherboard without City ConnectionContinued on next page •4100-6057 Fiber-OpticMedia Card •4100-6056Wired Media CardFigure 5-5.The 4100/4120-0142Wired Media Card Each module is shown belowEnvironmental Specifications All Modules Step 1. Configuring Network CardsSpecifications Electrical Specifications MotherboardStep 1. Configuring Network Cards, Continued Step 2. Mounting Media Cards to the NIC Figure 5-6.Media Card MountingStep 3. Mounting Network Cards Figure 5-7.Installing the Daughter CardStep 4. Wiring Network Cards Overview Wiring GuidelinesContinued on next page Step 4. Wiring Network Cards, Continued Table 5-2.Wiring DistancesContinued on next page optic cable Step 4. Wiring Network Cards, ContinuedFigure 5-9.Fiber Wiring Continued on next pageStep 4. Wiring Network Cards, Continued Using 4190-9010 Bi-DirectionalCouplersContinued on next page Figure 5-10.Coupler Wiring Step 4. Wiring Network Cards, ContinuedThe illustration below shows coupler wiring connected to the 4100-6014NICWired Media Card Connection Step 4. Wiring Network Cards, ContinuedWired Media Card Connection Motherboard Port for MediaWiring Illustrations Wired Media Style 7 Wiring Step 4. Wiring Network Cards, ContinuedFigure 5-12.Wired Media, Style 7 Wiring Continued on next pageFiber Optic Style 7 Wiring Step 4. Wiring Network Cards, ContinuedFigure 5-13.Fiber Optic, Style 7 Wiring Continued on next pageStyle 7 Wiring Step 4. Wiring Network Cards , ContinuedWired Media and Fiber OpticPage Topic The System Power Supply & Alarm Relay CardChapter See Page #AC Input Specifications SPS SpecificationsTable 6-1.SPS Input and Output Specifications DC Output SpecificationsAlarm Conditions SPS Specifications, ContinuedTable 6-2.SPS Current Specifications Standby ConditionsR341 Battery Charger Voltage SPS ConfigurationSPS Specifications, Continued R342 Voltage Measurement CalibrationSPS LED Indications The SPS has the following LEDsClass A Trouble Earth Fault Search Short Circuit Troubleshooting on SPSOverview IDNet Power Monitor Trouble Extra Device Channel Fail No Answer Bad Answer Output AbnormalThe Alarm Relay Card Figure 6-1.The Alarm Relay CardThe Alarm Relay Card, Continued Table 6-3.Alarm Relay Card Jumper PositionsChapter SPS Field Wiring 4100U TopicSee Page # General Field Wiring Guidelines Figure 7-1.The Ferrite Bead SX0005Continued on next page SPS NAC Field Wiring Guidelines Continued on next pageFigure 7-2.Class A NAC Wiring SPS NAC Field Wiring Guidelines, ContinuedSPS NAC Field Wiring Guidelines, Continued Continued on next pagePower Supply Wiring Distances Figure 7-3.Class B WiringMax Distance Table 7-1.Class A Wiring DistancesAlarm Max DistanceAlarm Power Supply Wiring Distances, ContinuedTable 7-2.Class B Wiring Distances Max DistanceSPS Auxiliary Power Wiring Continued on next pageSPS Auxiliary Power Wiring, Continued Figure 7-4.Auxiliary Power WiringSPS Relay Wiring SPS Auxiliary Relay Wiring, Continued The Figure below shows the SPS relaysRelays SPS IDNet Wiring Overview IDNet Wiring GuidelinesContinued on next page SPS IDNet Wiring, Continued Figure 7-6.Class A WiringContinued on next page SPS IDNet Wiring, Continued Figure 7-7.Class B WiringChapter Installing 4100U IDNet & 4100MXP Cards TopicSee Page # The IDNet Card Figure 8-1.The IDNet CardElectrical Specifications The IDNet Card, ContinuedTable 8-1.IDNet Specifications Environmental SpecificationsInstalling the IDNet Card onto the PDI Installing the ID-Netinto a 4100 Card Bay A- A+ B- B+Figure 8-3.Mounting into 4100 legacy Bay Configuring the Card 1 2 3 4 5 6 7Figure 8-4.DIP Switch SW1 Wiring to IDNet Devices Continued on next pageTable 8-2Cable Run Lengths Wiring to IDNet Devices, ContinuedFigure 8-5.Class A Wiring Continued on next pageWiring to IDNet Devices, Continued Figure 8-6.Class B WiringTroubleshooting on IDNet The 4100MXP Introduction Power ConnectionPage See Page # Chapter PC Software ConnectionsTopic Software ModesFigure 9-2.Data Transfer Interface Software ModesFigure 9-1.Service and Diagnostic Interface Continued on next pagerunning Bootloader Software Modes, ContinuedFigure 9-3.Bootloader Interface Software ModesPage Chapter Australian Version Specifics TopicSee Page # Summary Of Australian Version Specifics Australian Panel Format Table 10-2.Switch Status 4100U Fan Control ModuleTable 10-1.Switch/LED Format Continued on next pageFigure 10-1.Fan Control Module Brigade Interfaces Chapter TopicSee Page # Installation Checklist NotesAlignment & Adjustment Power Up & Placing into Operation Maintenance Page 1 2 3 4 5 6 7 Appendix A The Device Configuration DIP SwitchFigure A-1.DIP Switch SWx Continued on next pagecontinued Table A-1.Card AddressesOverview AddressTopic Appendix B Programming RequirementsRequired Features See Page #Appendix C Checking System Wiring NotesContinued on next page Circuit Type Appendix C: Checking System Wiring, ContinuedMeter Readings Meter ReadingAppendix D Earth Fault Detection General Guidelines Earth Fault Searching from the Front Panel Continued on next pagethe Next and Previous buttons Continued on next pagePress the Enter button to start the search Search Results Continued on next pageEARTH FAULT Search Results, ContinuedEARTH FAULT EARTH FAULTA. Find and repair the fault in the main panel Earth Fault Search ExampleFigure F-1.Earth Fault Example Continued on next pageSearch Results, Continued 1.Select Location SearchAppendix E Related Documentation Continued on next pageBook Part Appendix E: Related Documentation, ContinuedContinued on next page Title contTitle cont Appendix E: Related Documentation, ContinuedBook Part NumberTopic Appendix F Compatible Actuating DevicesList of Approved Devices See Page #Olsen Range - Conventional Detectors List of Approved Devices, ContinuedHochiki Range - Conventional Detectors Apollo Range - Conventional DetectorsCerberus Range - Conventional Detectors List of Approved Devices, ContinuedBrooks Range - Conventional Detectors Simplex Range - Analog Addressable SensorsCompatible Detectors, IDNET List of Approved Devices, ContinuedCompatible Addressable Field Devices, IDNet •Century Power Sonic PS12 series Appendix G Compatible Batteries•Power Sonic PS12 Series •Power Block PB12 series G-1Appendix H 4100U Specifications Voltage & Current Ratings of Modules & Assemblies Power Supply & Battery Capacity Calculations AppendixCopper Line Characteristics Appendix J Cable CharacteristicsLine Characteristics Continued on next pagePower Margin Network, ContinuedFibre Optic Cable Characteristics Fibre CableFibreAppendix K List of Drawings