Hpf Lpf | Vax M-9000 specification

(A9) HPF and LPF settings (when the D-001T is used)

H P F – 4 0 0 H Z L P F – 1 2.5

Rotate the Parameter setting knob to set the cut-off frequencies.

Press the Right or Left shift key to select HPF or LPF, of which parameter that flashes can be adjusted.

Setting Range

HPF

LPF

OFF (default), 20, 25, 31.5, 40, 50, 63, 80, 100, 125, 160, 200, 250, 315, 400 Hz

OFF (default), 4 k, 5 k, 6.3 k, 8 k, 10 k, 12.5 k, 16 k, 20 kHz

(A10) Compressor setting (when the D-001T is used)

C O M P R E S S O R – O F F

Setting Range

OFF (default), 1, 2, 3, 4, 5

Use the compressor to prevent power amplifier overload or to produce more easily heard sound by averaging the audio level. The number shows the compressor's effectiveness level, which can be set by rotating the Parameter setting knob.

•1 (Peak limiter)

Provides a peak limiter function that protects amplifiers and speakers against damage caused by an excessive signal input.

This level is suited to speech applications.

•2 (Peak limiter)

Provides a peak limiter function that protects amplifiers and speakers against damage caused by an excessive signal input.

This level is suited to musical applications.

•3 (Sonic normalizer)

Equalizes the sound volume of reproduced BGM among CDs or pieces of music by boosting small sounds and lowering big sounds, making the entire sound volume uniform.

This level is suited to BGM reproduction.

•4 (Speech leveler)

Makes paging calls easier to hear by equalizing the difference in speech signal volume that may result from individual differences in speaker voice volumes or variations in speaker-to-microphone distances.

Since the volume is extensively corrected, the feedback margin narrows, making it liable to occurrences of feedback. Therefore, special care must be taken when installing microphones and speakers.

This level is suited to microphone speech applications.

•5 (Speech leveler)

Makes paging calls easier to hear by equalizing the difference in speech signal volume that may result from individual differences in speaker voice volumes or variations in speaker-to-microphone distances.

This level 5 is more effective than level 4 described above. Since the volume is extensively corrected, the feedback margin narrows, making it liable to occurrences of feedback. Therefore, special care must be taken when installing microphones and speakers.

This level is suited to microphone speech applications.

42

Image 42

Vax M-9000 operating instructions Hpf Lpf

Contents

Series Amplifiers Operating Instructions Table of Contents Setting Dimensional Diagrams Specifications Important Safety Instructions FCC Requirements When Installing the Unit Safety PrecautionsSafety Symbol and Message Conventions When the Unit is in Use Over 10 cm General Description Features Installation Precautions Handling Precautions Nomenclature and Functions Fault indicator Emergency indicatorUnit indicator Input meter status indicator Output meter status indicator Output meterOutput level indication Changing the indicated channels on the Level output meter 9060S, A-9120S 90009060DH, A-9120DH, A-9120DL 9240SH Preamplifier output Power amplifier input terminals Mode switchBlank panel accessory Speaker output terminal Monaural input terminals 1 Optional Modules1. D-001T 2-Channel Input Module 2. T-001T Audio Output Expansion Module ZP-001T Zone Paging Module Telephone input terminal TELControl input terminal Contact Control output terminal OUT 1, 2, 3, 4, 5, 6, 7, 8, E 4. C-001T Control I/O Expansion ModuleControl input terminal in 1, 2, 3, 4, 5, 6, 7, 8, E AN-001T Ambient Noise Sensor Input Module Optional Accessories AN-9001 Ceiling Mount MicrophoneFront Side Rear ZM-9001 Zone Manager Bottom Control buttons 1Control output terminal E, OUT Volume control ZM-9002 Zone Manager Description of Mixer Mode General Description Application example for a ball room, meeting room, etc Glossary ANC Ambient Noise Control function AN-001T only Basic Operation Power ON/OFFOperation Keys and knobs Changing the output parameters Input channel ON/OFFOutput channel ON/OFF Recalling Scene Memory Paging port mode Zone Paging Ring signal mode Example when input keys are locked Releasing Key Lock Operation Example Setting Setting Menu Flow Basic Setting Operation Moving to setting screensTip Setting content selection Returning to the upper hierarchy level Input Setting Setting flow chart 43-A15 A2 Input channel name setting Input setting itemsA1 Input gain setting 1 I N + 1 2 0 HPF LPF A14 Operation mode setting when the ZP-001T is used D E = P a G I N G P O R T X I M U M L E V E L M P L E T I M E I N R a T I O C K E R P R I O R I T Y A24 Ducker ON/OFF setting when the AN-001T is not usedC K E R O F F Priority Audio Output Setting T 1 O U T E Q = a L L F L a T B5 Speaker parameter presettingSpeaker EQ settings 122SUBWFER*1 1SUBWOOFER*2 2SUBWOOFER*33SUBWOOFER*4 SR-S4 SINGLE*6 HX-5E LOCUT*8 B7 HPF and LPF settings F 4 0 0 H Z L P F 1 B8 Compressor setting M P R E S S O R O F F B9 Delay ON/OFF setting L a Y O F FPage Utility Setting Interlock output control setting G I N G O F F M a T T E N U a T E N 0 1 N O N E N =N = 1 2 3 4 5 6 7 8 9 a B C M O T E 1 V O L U M E U T =U T = 1 2 3 4 5 6 7 8 9 a B C M O T E 1 O U T P U T N S E L S Y N C O N C20 Communication speed bps setting R I a L S P E E D = 5 C18 Password settingC19 Gate release time setting T E R E L E a S E T I M E C17 Lock status display Y L O C K U N L O C K E D C22 Firmware version indication R M V E R S I O N = 1.1 C23 Memory initialization I T I a L I Z E O K ? Paging Setting Paging function SP1 SP2 SP3 SP4 65-D2 Paging setting items D1 Paging input channel setting G I N G O N I NG I N G T R I G Z P G I N G S Y N C O F F G I N G D I S a B L E O F F Control input terminal Control Input Function Setting When the control input function Is set to EMG-MUTE p -E16 Control input function setting items E1 Control input function setting N 0 1 N O N EN 0 1 L O a D B a N K N 0 1 V O L U P E8 Volume increasing level settingE9 Volume decreasing level setting N 0 1 V O L D O W N E11 Input/Output channel number selection N 0 1 C H O N N 0 1 S Y N C E14 Interlock output control settingE17 Interlock output control setting N 0 1 E M G M U T EPage Control Output Function Setting Control output function setting items F1 Control output function setting U T 0 1 N O N EF4 Scene memory bank number selection U T 0 1 S C E N E F6 Input/Output channel number selection U T 0 1 C H O N I N ALL Key Lock Function SettingKeys that can be locked Util All-key lock ON/OFF p -G1 Y L O C K a L L O F F Y L O C K I N P U T O F FY L O C K O U T P U T O F F Y L O C K U T I L O F F G6 Setting key lock ON/OFFG7 Power switch lock ON/OFF Y L O C K P O W E R O F F Password setting Key lock setting operation Memory Setting Scene memory save p -H3 A D E N E S E T T I N G S a V EV E H5 Scene memory erasure when Erase is set A S EW E R O N L a S T S T a T E HOW to Store or Erase Scene Memory Storing Scene Memory Erasing Scene Memory Press for over 2 seconds Setting the Scene Memory to be Recalled at Power-On Restoring Factory Default Setting Default Setting Table Audio output settings ALL Flat Trigger C-IN Utility settingsPaging input settings Trigger VOX Control input function Loadbank Control input function settingControl output function setting Control input function Volup Scene memory Erase Memory settingsScene memory Save Scene memory P-ON Module Combination Module InstallationModule Installation Channel Numbers and Terminal Numbers Insert the C-001T module in the open slot Module Installation Examples Control I/O Terminal Connections Remote volumes 1Connections Control inputs 1 Control outputs 1 Operation by control input Pulse trigger Level trigger 100 Transformer output terminal connectionDirect output terminal connection Control input terminal 10114.3. C-001T Module Connections Control output terminal RS-232C Connector Connection 102AN-001T and AN-9001 Connections Removable Terminal Plug Connection Connector connection103 Cable end treatment 104 Rack Mounting Bracket Attachment AN-9001 Installation 105Tips AN-9001 Dimensional Diagrams106 Front Bottom ZM-9002 107ZM-9001 Front Bottom Front View without panel Side HOW to USE the Supplied Software 108System requirements Installing the Software Connecting the Unit to the PC109 Setting the Communication Port and Speed 110 111 Updating the Firmware 112 113 Storing or Recalling Parameters Set at the Unit 114 115 Monitoring the Units Operation StatusScreen indications and their descriptions 116 117 Activating the Control InputStep Error Indications 118 Troubleshooting 119 Block Diagram 120 Signal Flow Diagram 121ZP-001T Zone Paging ADC LPF Level Diagram122 Slot Specifications 24.1. M-9000 123 Accessories 124 125 24.2. A-9060DH, A-9120DH 126 127 24.3. A-9120DL 128 129 24.4. A-9060S, A-9120S 130 131 24.5. A-9240SH 132 133 24.6.1. D-001TCmrr 134 24.6.2. T-001T 135 24.6.3. C-001TZP-001T 136 AN-001T ZM-9001 137AN-9001 ZM-9002 200604