9

Tools Needed:

Power Drill

7/16” Socket

Driver

Stacking Sections

NOTE: For door section identification see page 4.

NOTE: Make sure hinge leafs are flipped down, when stacking another section on top. Place rollers in hinge tubes of the second section (lock section). With assistance, lift second section and guide rollers into the vertical tracks. Align vertical marks in the upper alignment sticker, with the lower alignment sticker on right hand side on the back of door. Keep sections aligned and fasten hinges to connect the sections using 1/4” - 14 x 5/8” self-tapping screws. Repeat for other section(s) except top section. IMPORTANT: When securing the end hinges to the sections with 1/4” - 14 x 5/8” self-tapping screws, ensure they are attached as shown in the illustrations above.

IMPORTANT: Push & hold the hinge leafs against section while securing with 1/4” - 14 x 5/8” self-tapping screws. End Hinges have (2) screws and Intermediate hinges have (3) screws.

(2) 1/4” - 14 X 5/8”

SELF-TAPPING SCREWS

Alignment stickers

Right end hinge

(2) 1/4” - 14 X 5/8”

SELF-TAPPING SCREWS

Left end hinge

(3) 1/4” - 14 X 5/8”

SELF-TAPPING SCREWS

Intermediate hinge

 

 

 

 

 

 

 

(2) 1/4” - 14 X 5/8”

 

 

 

(3) 1/4” - 14 X 5/8” SELF-TAPPING

 

 

 

SELF-TAPPING SCREWS

SCREWS

 

 

 

 

 

 

 

End hinges (left hand shown, right

Intermediate hinges

 

 

hinge symmetrically opposite)

 

 

 

 

 

 

 

 

 

10

Top Brackets

2nd set of holes

 

 

 

 

 

 

 

 

from bottom

 

 

 

Tools Needed:

NOTE: For door section identification see

Top section

 

 

 

 

Power Drill

page 4.

 

 

 

 

 

 

 

 

 

 

 

Endcap

 

 

 

7/16” Socket

To install the L-shaped top brackets,

 

 

 

 

 

 

 

 

 

Driver

align the top holes in the top bracket

 

 

 

 

 

 

base with the second set of holes from

 

TOP BRACKET BASE

 

 

 

bottom of endcap.

 

 

 

 

 

 

 

 

 

 

Fasten top bracket base to endcap using

TOP

 

 

 

 

 

SECTION

 

 

 

 

 

(4) 1/4” - 14 x 5/8” self-tapping screws.

 

 

(4) 1/4” - 14 x 5/8”

 

 

 

 

 

 

 

Secure the top bracket slide to the

 

 

 

SELF TAPPING

 

 

bracket base loosely using (2)

 

2nd set of

 

SCREWS

 

 

 

 

 

 

 

1/4” - 20 x 5/8” carriage bolts and (2)

 

 

 

 

 

 

holes from

 

 

 

 

1/4” - 20 flanged hex nuts. The bracket

 

bottom

 

 

 

 

will be tightened and adjusted in Step

 

 

 

 

 

 

15. Insert rollers into top bracket slide.

(2) 1/4” - 20 x 5/8”

TOP BRACKET

TOP

TOP BRACKET

 

 

 

CARRIAGE BOLTS

SLIDE

SECTION

SLIDE

ROLLER

 

Repeat for other side.

 

 

 

 

 

 

 

 

 

(2) 1/4” - 20

FLANGED

HEX NUTS

16Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your local

yellow pages business listings or go to the Find a Dealer section online at www.Wayne-Dalton.com

Page 16
Image 16
Wayne-Dalton 341458 installation instructions Stacking Sections, Top Brackets