Wayne-Dalton 341458 TorqueMaster Plus Reset Instructions Continued, Installation

Models: 341458

1 38
Download 38 pages 17.55 Kb
Page 31
Image 31
TorqueMaster® Plus Reset

TorqueMaster® Plus Reset

Instructions Continued...

Tools Needed:

If the system is engaged, follow these

steps to reset the system:

 

2.Disengage opener (if installed) by pulling or placing emergency disconnect in the manual operated position.

3.With the door in the open position, clamp vice grips on both tracks just below the bottom section roller.

4.Now is a good time to remove vehicles from garage, and provide clear access to end brackets.

5.Flip the ratchet pawl knob on both

end brackets to the upper position (see illustration).

Place vice clamps

BELOW BOTTOM SECTION on both vertical track

6.Raise door 2”-3” and then lower door. Repeat process until anti-drop device resets (see disengaged illustrations on reverse side).

IMPORTANT: BE PREPARED TO SUPPORT THE TOTAL WEIGHT OF THE DOOR.

7.Cautiously remove the vice clamps from both tracks and with assistance lower the door.

8.Check for spring tension. Starting on the right hand side, place a ratchet and 5/8” socket on the Torquemaster® Plus winding shaft (see illustration in instruction manual). Ensure ratchet is set so that it will tighten counter clockwise on the right hand side, and clockwise on the left hand side (if applicable). If tension is present, remove the ratchet and check the left hand side (if applicable). If spring(s) have tension, proceed to Balancing Door Step 1; if no spring tension is present, contact a qualified door installation company to replace the spring(s).

Lower Position

Pawl Knob in Lower

Position

UPPER Position

Pawl knob in UPPER

Position

INSTALLATION

IMPORTANT: HAVE A QUALIFIED DOOR INSTALLATION COMPANY MAKE ADJUSTMENTS/REPAIRS TO CABLES, SPRING ASSEMBLIES AND OTHER HARDWARE.

BALANCING DOOR

1.Lift door and check its balance. Adjust spring(s), if door lifts by itself (hard to pull down) or if door is difficult to lift (easy to pull down). Anytime spring adjustments are made, ratchet pawl knob must be

in the upper position (see illustration on reverse side). An unbalanced door such as this can cause idrive® or Torquemaster® Plus operation problems.

End Bracket

Ratchet with 5/8” Manual background Socket

PAWL

 

To

 

 

 

 

 

 

 

 

fatal

,

 

 

 

 

 

 

 

 

until

from

 

 

 

 

 

 

 

To

spr

 

 

 

 

 

 

 

 

safely

 

 

 

 

 

 

 

 

and follow

 

read

i

(

 

 

3” Extension

 

installationthe d

ire

 

 

 

 

DO

NOT

 

 

 

 

 

 

 

 

instructiotions

in

 

 

 

 

 

manual

 

 

Dr

 

 

No space betREMOVE. ns/ownersthe

 

 

 

 

Ratchet

Pawlweena

 

THIS

TA

 

 

 

 

 

Cable

Drum

nd

 

 

G.

e Ratchet

 

 

 

 

DISENGAGED

SIDE VIEW

 

 

um

 

 

 

 

 

 

 

 

 

 

DISENG

AGED U

 

 

 

 

 

 

 

 

 

 

NDERNEATH VI

 

 

 

 

 

 

 

Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your local 31 yellow pages business listings or go to the Find a Dealer section online at www.Wayne-Dalton.com

Page 31
Image 31
Wayne-Dalton 341458 installation instructions TorqueMaster Plus Reset Instructions Continued, Installation