Worth Data 701 RF manual ONE-WAY Setup Mode Sign on Site Testing

Q

quiet zone 8-7

R

R/F Serial Pin-outs	C-1
R/F Terminal Firmware Upgrades	D-1
R/F Terminal Menu Functions
ONE-WAY	1-6
SETUP MODE	1-6
SIGN ON	1-6
SITE TESTING	1-6
Radio traffic contention	4-6
Raising the Base station to increase range	4-1
Range problems	8-5
Reader doesn't beep when reading bar codes	8-7
reading credit cards	6-4
reading magstripe	6-4
reading through a windshield	L-3
Reading through a windshield	L-3
reaing in sunlight using aiming dot	L-3
Re-assigning character codes	2-17
rechargeable batteries	2-18
recharging battery procedure	1-6

Recording a voice message using the microphone ... 7-3

Recording and Playback of Voice Messages	............ 7-3
Recording time alloted for voice messages	7-2
Recovering from hardware failures	5-2
Recv Setup/Voice Please Wait	7-5
Red LED	8-4
Reduced Space Symbology code	2-14
Re-initailizing terminals	6-2
Reinitialization
of Base Station with Terminal Signed-On	.......... 6-12
Re-initialize command	6-3
Relay Cannot be Heard	8-4
Relay Existence setup parameter
how to set for Relays	4-4
Relay ID - configuring	2-23
Relay ID and Frequency	B-4
Relay n Cannot Be Heard by the Base	B-4,B-6

RELAY n CANNOT BE HEARD BY THE BASE . 4-4

Relay Setup	2-22
Relay Station failures	B-3,B-6
Relay Station RS422 Pin-outs	B-3,C-2
Relay stations cable failures	B-3,B-6
Relay Stations
changing a Base to operate as a Relay	A-1
connecting	B-1
multi-dropping additional	B-1
no serial parameters needed	B-2
troubleshooting unconnected relay	B-4,B-6
using to extend RF range	B-1
Relay test cable	B-4
relay wiring	B-2
Relays
overlapping area with Base	4-5
RS-422 termination	A-2,B-6
resending prompts after a sign-out	5-3
Reset	2-21
response time is poor	8-5
Restrictions on bar code data length	2-15
Restrictions on using arrow keys to transmit special
characters	6-12
Results of Site Test	4-2
retransmission	3-3
returns to 1st screen	8-6

RF 700 Configuration Utility		2-22
RF link test		2-23
RF System
Base Station failures		5-3
before you begin programming		5-1
creating programs to prompt the terminal		6-1
operator errors		5-3
planning for expansion		5-2
planning for failures		5-1
planning for hardware failures		5-2
Relay station failures	B-3,B-6
using Demo programs to test system		5-2
RF System Setup		2-1
RF Terminal
how it finds a Relay		4-4
installation		1-4
opening screen		1-6
sleep mode and wake up intervals		3-3
system components		1-1
RF Terminal Cases and Holsters		N-4
RF Terminal Channel		2-5
RF Terminal Default Settings		2-1
RF Terminal ID		2-5
in programing message from host to terminal		6-1
RF Terminal Problems		8-6
RF Terminal setup
using keypad to setup		2-3
using the bar coded setup menu		2-2
RF Terminal Setup		2-1
2 of 5 Code		2-13
2 of 5 Length		2-14
Batteries		2-18
Baud Rate for serial printer		2-21
Beep Tone		2-18
Characters		2-17
Code 3 of 9		2-10
Data Bits setting for serial printer		2-21
Date Format		2-18
Display of Year		2-19
ENTER key elimination for Control Keys Only ..		2-6
Laser Scanner Options		2-20
LCD Backlight Display Mode		2-7
LCD Display Mode		2-7
MSI/Plessey		2-14
Parity for serial printer		2-21
Preamble		2-15
Protocol setting for serial printer		2-21
Reset		2-21
RF Terminal Channel		2-5
RF Terminal ID		2-5
RSS-14 code		2-14
Security Code		2-6
Set Date		2-19
Set Time		2-19
Shut Down Time		2-20
Skip Opening Screens		2-8
Stop Bits setting for serial printer		2-21
Voice Message Partitions	2-19,2-20
RF Terminal Setup
Codabar		2-13
Code 128		2-12
Code 93		2-15
UPC/EAN		2-11
RF Terminal Setup Menu on keypad		2-3
RF Terminal Setup Parameters		2-5
RIGHT ARROW key
transmitting ASCII 31 to host		6-12
RMA's		8-8

5