Message | Xerox 4050 NPS, 4090 NPS, 4890 NPS, 4850 NPS guide

PRINTER CONTROLLER MESSAGES

Message

J185 Stacker elevator fails to reach new position.

J188 Exposure level exceeded target + tolerance.

J191 Pixel clock error or SOS/ EOS scan lines missing.

J197 SOS/EOS not balanced.

J198 Polygon motor assembly producing extra scan lines.

J213 PIXEL board VCO voltage out of window during print.

J217 Interpolation overflow

detected.

J230 Dicorotron 1 fault.

J232 Charge 2 shield voltage at max.

J246 Transfer assist blade engage failure.

Explanation/action

The stacker elevator failed two successive attempts to reach a new position.

No action required.

If problem persists, notify your service representative.

The laser exposure did not stabilize to the specified level after power up, or the exposure level exceeded the prescribed limits.

No action required.

If problem persists, notify your service representative.

The pixel clock output malfunctioned.

No action required.

If problem persists, notify your service representative.

The ROS intensity difference is not balanced.

No action required.

If problem persists, notify your service representative.

An extra scan pulse (EOS or SOS) occurred within the scan window time limit.

No action required.

If problem persists, notify your service representative.

The VCO (Voltage Controlled Oscillator) voltage is not within an acceptable range. If this fault occurs during imaging, then a ROS PURGE will occur as well.

No action required.

If problem persists, notify your service representative.

There has been an error in the conversion of 300 dpi data to 600 dpi data.

No action required.

If problem persists, notify your service representative.

The charge 1 shield voltage or the charge 1 shield current is out of tolerance.

No action required.

If problem persists, notify your service representative.

The current charge value has exceeded 204 bits during cycle up of xerographics.

No action required.

If problem persists, notify your service representative.

The transfer assist blade function failed to initialize because solenoids did not engage while level two is NVM enabled.

No action required.

If problem persists, notify your service representative.

XEROX DOCUPRINT 4050/4090/4850/4890/92C NPS MESSAGES GUIDE

48-35

Image 99

Xerox 4050 NPS, 4090 NPS, 4890 NPS, 4850 NPS manual Message

4050 NPS, 4850 NPS, 4090 NPS, 4890 NPS specifications

The Xerox 4890 NPS, 4090 NPS, 4850 NPS, and 4050 NPS are part of Xerox's family of high-performance production printers, designed to meet the demanding needs of commercial printing and large-scale document production. These models integrate advanced technologies and features that enhance productivity, efficiency, and print quality.

The Xerox 4890 NPS stands out for its high-speed capabilities, delivering up to 90 pages per minute. It utilizes a sophisticated print engine that ensures consistent quality across a variety of media. Equipped with the latest digital technology, the 4890 offers sharp imaging and vibrant color reproduction, making it ideal for producing professional-grade marketing materials, reports, and brochures. The system is also designed with user-friendly interfaces, making it easy for operators to manage jobs efficiently.

Similarly, the Xerox 4090 NPS is another powerful model in the line, known for its adaptability and speed, providing up to 90 pages per minute as well. This model supports a wide range of media sizes and types, from lightweight paper to heavier stock, without compromising quality. The 4090 NPS features a robust finishing capability, allowing users to create professionally bound documents, making it a versatile choice for printing houses and corporate environments.

The Xerox 4850 NPS brings a balance of speed and quality, producing documents at 85 pages per minute. This model emphasizes energy efficiency, using economical printing techniques that reduce power consumption while maintaining exceptional print quality. The 4850 is particularly suited for high-volume printing tasks, combining durability with operational efficiency.

Lastly, the Xerox 4050 NPS is known for its compact design and ease of use, making it an excellent choice for environments with limited space. Despite its smaller footprint, it delivers an impressive speed of up to 50 pages per minute and is ideal for producing high-quality documents on demand. The 4050 integrates advanced networking capabilities, enabling seamless integration into existing workflows.

Each of these models leverages Xerox's expertise in digital printing technologies, including advanced toner formulations and high-capacity paper handling systems. They also come equipped with security features that protect sensitive data during the print process. Together, these printers provide a robust solution for businesses looking to optimize their document production capabilities while ensuring high-quality output and efficiency.

Contents

Version 7.1 August 2000 721P86941 Page Version 7.1 August 2000 721P86941 Page Laser safety Xerox Docuprint 4050/4090/4850/4890/92C NPS Messages Guide Laser safety Xerox Docuprint 4050/4090/4850/4890/92C NPS Messages Guide Table of Contents Page Table of Contents Page Introduction Conventions Xerox DocuPrint Network Printer Series Page Introduction Conventions Xerox DocuPrint Network Printer Series Page Printer Controller messages Explanation/action Message 48-3 48-4 48-5 48-6 48-7 48-8 Message Explanation/action PS-adminShow Status Messages using Show Status Queuing is Started Scheduling Policy resourceMatch PS-admin C076 Sfrs 48-14 Clear areas 1A and 2A 48-16 48-17 Clear area 2a 48-19 48-20 48-21 48-22 48-23 Bin #1 sensor 48-25 48-26 48-27 48-28 48-29 48-30 48-31 48-32 48-33 Loss of some supply voltage to XER 48-35 48-36 48-37 Type PSP 48-40 48-41 General system messages Memory System Communication FAULT, see Message AT CRT Printer Controller messages 48-2 48-3 48-4 48-5 48-6 48-7 48-8 Message Explanation/action Messages using Show Status Message C076 Message Explanation/action 48-14 Clear areas 1A and 2A 48-16 48-17 Message Explanation/action 48-19 Message 48-21 48-22 48-23 Bin #1 sensor 48-25 Message Explanation/action 48-27 48-28 48-29 Message 48-31 48-32 48-33 Loss of some supply voltage to XER Message 48-36 48-37 Type PSP 48-40 Message Explanation/action General system messages Memory System Communication FAULT, see Message AT CRT Job Ticket must have an extension of .XJT Fatal memory error has occurred. Close some applicationsRestart the Xpps application Job Name is Required Read. There may be a memory problem. The operation is Problem occurred while the command-line arguments wereCancelled Problem occurred while the dropped file names were being Close some applications or add more memory An entry using this page already existsAn error occurred while attempting to free allocate global Network printer An error occurred while the file containing the printer This printer. Call the System AdministratorFor this printer. Call the System Administrator Does not exist or you do not have read access An exception page can not be added when the Image shift Use You must have write accessAn error occurred while XDS was converting the Job Ticket Serviced by this print server. You may not have enough Fields set to Printer default Set to Printer defaultAn exception page can not be added when the Sides imaged To Printer default Code b95p An internal processing error occurred during the printingOperation. You may not have enough memory. Internal error Ticket Library Bound collated sets must contain between 7 and 125 sheets An invalid insert position has been selectedArgument %s is invalid Argument % is invalid. Skip this argument and continue? Copies must be Bound jobs require a paper length of 11.0 inches 279 mm orInches 297 mm Copies must be 1-16 for uncollated Booklet Maker jobs Copies must be 2-70 for uncollated stapled jobs Copies must be 2-50 for uncollated stapled jobs Delete the selected printer? DefaultCopies must be 7-125 for uncollated bound jobs Covers can not use a paper stock with fields set to Printer Enter valid numbers in the Tab Position Field Do you wish to reset to the default Job Ticket values?Values? Enter a sender name in the From field Failed to print the document. An LPR operation timed out Feature conflicts have been found in the Job Ticket. SelectSetup button When paper stock lengths vary If Uncollated and ordered Custom paper type are selected, Order Count must beJobs cannot use more than two ordered stocks No printer connection is selected. a printer connection is One or more stocks have a paper weight that is not betweenJob consisting entirely of transparencies cannot be stapled Or bound Range overlaps an existing range 413 g/m2Only one Chapter Start can be programmed per Ordered stock must have a value Paper stock width must be from 7.00 to 18.27 inches to Paper stock width must be from 203 mm to 216 mm,Paper stock width must be from 203 mm to 432 mm, Length must be from 254 mm to 363 mm Paper stock widths less than 9.0 inches 229 mm cannot be Paper stock width must be from 8.00 inches to 8.50 inches,Length must be from 10.00 inches to 14.02 inches Paper stock widths cannot vary by more than 0.5 inches Paper stocks with widths greater than 9.0 inches 229 mm Paper Weight must have a value between 60 and 413 g/m2Inches 363 mm cannot be bound or stapled Paper stocks with a Custom paper type cannot be drilled Account field cannot begin with a Space NecessaryStapled collated sets must contain between 2 and 50 sheets Stapled collated sets must contain between 2 and 70 sheets Characters hyphen-, slash/, asterisk*, plus sign+, number Currently selected printer is now the default printerAccount field may contain upper case alphabetic Characters, numerals 0 through 9, a blank, or the following Job location Destination and the document file names must differDestination name must not have an extension of XJT Destination of Save or Print & Save requires a valid saved Down or the connection timed out Do not have access rightsNot have access rights. Call the System Administrator Document cannot be copied to the spool directory on File %s is invalid and can not be dropped System AdministratorEntered page range is invalid Exception Pages range From must be greater than zero Continue? File containing the printer capabilities cannot be openedFile containing the printer capabilities is corrupted Do not have read access to the file Will fault at the printer. Do you want the Job Name to beSelected printer. Assign defaults to the indicated areas or Cancel the operation? Job Ticket file cannot be found. You must specify a name Be used. To modify those settings, reprogram the Job TicketSetup Job Ticket is invalid Maximum number of Chapter Starts has been defined Directory. Notify the System AdministratorLocal family mask file .MSK for this printer does not exist Or cannot be opened. It should be located in your Windows Necessary Product Support Library is not loaded. To reinstall XppsNetwork Server configuration file QUEUE.CFG for this Notify the System Administrator Range values must be Number specified by To exceeds the total numberPages in the job From field. Enter only numeric values Overwrite it? Print job was cancelledJob Ticket features could not be determined Print & Save Destination Job Ticket already exists Printer specified in the file containing the printer Printer setup structure for the Xerox Job Ticket LibraryCould not be created and initialized Printer specified in the connection is not supported To a connected printer Selected queue is not configured for Xerox useDocuSP Server Save Destination Job Ticket already exists. Overwrite it? Starting Page must be greater than zero Reinstall XDSInitialized. You may have to reinstall XDS Specified file already exists. Overwrite it? Support libraries required for the Xerox Job Ticket Library Reinstall XppsLibrary could not be loaded. You may have to reinstall Xpps Library are not the most recent version. You may have to Tab Positions must be from 1 through Library could not be loaded. You may have to reinstall XDSWeight for Paper stock 1 is not between 60 and 200 g/m2 Tab Control libraries that are required for the Xerox Job X Image Shift must be from -17.0 inches to 6.7 inches, Weight for Paper stock 1 is not between 60 and 413 g/m2Have to reinstall XDS Y Image Shift must be from -14.3 inches to 14.3 inches Image Shift must be from -372 mm to 372 mm X Image Shift must be from -216 mm to 216 mm, and the YImage Shift must be from -356 mm to 356 mm X Image Shift must be from -432 mm to 170 mm, and the Y Xerox Document Submission Application cannot load You may have to reinstall XDSAdministrator May have to reinstall XDS Application is unknown File, XPPPRES.DLL. You may have to reinstall XppsXerox Job Ticket libraries are invalid. You may have to Xerox Job Ticket Library cannot be loaded. The calling File, XRXUTIL.DLL. You may have to reinstall Xpps This application. You may have to reinstall XDSBe loaded. You may have to reinstall Xpps File, XPPPNET.DLL. You may have to reinstall Xpps You must restart windows and reinstall XDS Library file, XPPPNET.DLL. You may have to reinstall XppsLibraries. You may have to reinstall Xpps Needed to print documents or to setup Job Tickets. Select Accommodated by this dialog box. You must Change or Delete There was a problem while a window handle was being storedOr retrieved This operation results in more page ranges than can be Windows Check the default stockVersion of software. Some Job Ticket options will not be Available Please check the stocks being used in the Covers dialog Require 1-sided for Sides Imaged. Please check the defaultStocks being used in the Exception Pages dialog box Transparencies require None or Print on Side 1 for Printing Uncollated jobs cannot be sent to the Booklet Maker Or you do not have read accessUsed in the Exception Pages dialog Job was being closed. Resend the job Conventional memory. Close some other applications and try Application that is using Xppp and try againUncollated transparencies cannot be stapled or bound Uncollated transparencies cannot be stapled Restart Windows Exit and restart WindowsIs not a Novell NetWare server Minimum rights that are required are Write and Create 49-50 Windows workstation messages File. Retrieve it? Network printer This printer. Call the System Administrator File is corrupted Set to Printer default Ticket Library An invalid insert position has been selected Bound jobs require a paper length of 11.0 inches 279 mm or Copies must be 2-50 for uncollated stapled jobs Copies must be 7-125 for uncollated bound jobs Values? Failed to print the document. An LPR operation timed out If Uncollated and ordered Custom paper type are selected, Job consisting entirely of transparencies cannot be stapled 413 g/m2 Paper stock width must be from 203 mm to 216 mm, Paper stock width must be from 8.00 inches to 8.50 inches, Inches 363 mm cannot be bound or stapled Necessary Account field may contain upper case alphabetic Destination and the document file names must differ Document cannot be copied to the spool directory on System Administrator Continue? Will fault at the printer. Do you want the Job Name to be Job Ticket is invalid Local family mask file .MSK for this printer does not exist Necessary Product Support Library is not loaded. Number specified by To exceeds the total number Print & Save Destination Job Ticket already exists Printer setup structure for the Xerox Job Ticket Library Reprint or Print Server file path should not contain a drive Specified file already exists. Overwrite it? Library are not the most recent version. You may have to Xpps Weight for Paper stock 1 is not between 60 and 413 g/m2 X Image Shift must be from -216 mm to 216 mm, and the Y XDS Xerox Job Ticket libraries are invalid. You may have to Xerox Job Ticket Library, XPPP.DLL, does not recognize Library file, XPPPNET.DLL. You may have to reinstall Xpps There was a problem while a window handle was being stored Version of software. Some Job Ticket options will not be Stocks being used in the Exception Pages dialog box Used in the Exception Pages dialog Uncollated transparencies cannot be stapled or bound Restart Windows Minimum rights that are required are Write and Create 49-50 Application Name could not be printed on LaserWriter Because of a communication error, Document Name fromCould not find the default Job Ticket specified in the User Preferences dialog. Internal defaults will be used JPM down Problem establishing connection to specified printerQueuing is disabled LaserWriter is disconnected or switched off. Please try Application menu or check the PrintMonitor window Want PrintMonitor to adjust its memory size and try again?Selected ticket is not valid. The previous ticket remains Effect 50-4 Macintosh workstation messages JPM down Selected ticket is not valid. The previous ticket remains 50-4 Bad Queue Value virtual printer Bad Queue Value No queues configuredCan’t access path Ambiguous value for option Can’t initialize Sigquit handler Can’t add file to internal table pathCan’t get file from internal table # Can’t initialize Sigint handler Error getting initial working directory Error changing to directory pathError creating temporary data file Error copying STANDARD-INPUT Invalid indirection file Error getting unique data filenameError opening configuration file path JobTicket error for option JobTicketSetSourceDoc JobTicketOverlayJob TicketSetDispositions Job TicketSetSender Non-unique option Memory allocation errorLprtab2ps copy file is too large Missing value for option SetOfDispCreate SetOfDispInsertSystem error Server or directory unreachable Unable to find server name DOS workstation messages Can’t add file to internal table path Couldn’t encode job ticket to file Error getting unique data filename JobTicketOverlay Lprtab2ps copy file is too large Server or directory unreachable Unable to find server name Unix workstation messages Can’t create job ticket file Can’t create job ticket Client software was unable to access the directory using Entering the print command, an invalid option was specified 52-5 Lpr command was entered, but the job is too large. This is a Print request not forwarded 52-8 Unix workstation messages Can’t add file to internal table path Can’t open local printer file path Error copying STANDARD-INPUT JobTicketDecodeAXJT JTDocumentterCreate Print request not forwarded Unable to find listfile