Operation Advanced
Using the RTM Function
The 8080 incorporates a
HINT In the factory default condition, CONTROL pedal 1 is set to adjust the volume of each patch and CONTROL pedal 2 can be assigned to various parameters with the CONTROL switches. Before you make any changes, we suggest to try this out for yourself.
Using the CONTROL pedals for RTM
Using CONTROL pedals 1 and 2 to continuously adjust parameters such as volume or wah can be very effective during a performance. To do this, the following steps are required.
•In the TOTAL module, select the effect module to be assigned to CONTROL pedal 1 and 2.
•Within the selected effect module, select the parameter to be controlled and the change direction.
|
|
|
|
|
|
|
|
|
|
|
| EDIT |
|
|
|
|
|
|
|
|
|
|
|
|
|
| EXIT |
|
|
|
|
|
| Display |
|
|
|
|
| 1 | EDIT/EXIT key |
|
| |
|
|
|
|
|
|
|
|
|
| TOTAL |
|
| ||
|
|
|
|
|
|
|
|
|
| TOTAL key |
|
| ||
|
| FINE TUNE |
|
|
|
| CONTROL |
|
|
|
|
|
| |
|
|
|
|
|
|
|
| SWITCH |
| 3, 6, 7 |
|
|
| |
|
|
|
|
|
|
|
| INDICATOR |
|
|
|
| ||
|
|
|
|
|
|
|
| MAX |
| Data entry knobs | ||||
|
|
|
| MIN | MAX 1 | 2 MIN | MAX |
|
|
|
| |||
|
|
|
|
| 3 | 4 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 1/2 | INCREASE |
|
|
|
| MIN MAX |
|
|
|
| MIN | MAX | MIN | MAX |
|
|
|
|
|
| |
COMP EFF1 | DIST | EQ EFF2 | EFF3 DLY REV TOTAL |
|
|
|
|
| CONTROL |
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| UTILITY | |
|
|
|
|
|
|
|
|
| CONTROL | PEDAL |
|
|
| |
STORE | GROUP | EDIT | UTILITY | – TYPE + |
|
|
| MIN | SWITCH | 2, 5 | UTILITY/PAGE key | PAGE | ||
(EXECUTE) | COMPARE | EXIT | PAGE | PRESENCE | OUTPUT | BLINK | ||||||||
|
|
|
|
|
|
|
| (DLY:TAP) |
|
|
|
| ||
ADVANCED GUITAR EFFECTS PROCESSOR |
|
|
|
|
| DECREASE |
|
|
| |||||
|
|
|
|
|
|
|
|
| 8 |
|
|
|
| |
|
|
|
|
|
|
| USER |
|
|
|
|
|
| |
CONTROL |
| BANK |
|
| FUNCTION |
| STORE/EXECUTE key |
|
| |||||
PEDAL |
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
| STORE |
|
|
|
|
|
|
|
|
|
|
|
|
|
| (EXECUTE) |
|
|
|
|
|
|
|
|
|
|
|
| 4 | Effect key COMP | CONTROL |
| |
|
|
|
|
|
|
|
|
|
|
|
| PEDAL |
| |
|
|
|
|
|
|
|
|
|
| 9 | CONTROL pedal 1 |
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| ||
1
2
the EDIT/EXIT key .
Press the
UTILITY/PAGE key once. |
The 8080 enters the Edit mode. If the TOTAL key is not flashing, press the TOTAL key to select the TOTAL parameters.
3
| Data entry knob |
| Use | 3 to |
CONTROL pedal 1
CONTROL
PEDAL.
This page serves to assign effect modules to the CONTROL switches (data entry knob 2), CONTROL pedal 1 (data entry knob 3) and CONTROL pedal 2 (data entry knob 4).
The illustration below shows an example for assigning the EF3 effect module to CONTROL pedal 1.
CONTROL SET: CSW=DLY Ž 2 CP1=EF3 CP2=OFF4
Press the Effect key for the effect module assigned to the CONTROL pedal to display the parameters of that module.
| FLG | DPT=50 | SPD= | 50 |
Ž | FB= 0 | MAN= | 0 |
|
|
|
|