Using the USER FUNCTION switch to select PRESET A/B/C

The USER FUNCTION switch can be used to select a group among PRESET groups A, B, C. To do this, the function of the USER FUNCTION switch must be set to "PRESET" in Utility mode.

 

 

 

 

Display

 

 

 

 

 

2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FINE TUNE

 

 

 

 

 

 

CONTROL

 

 

 

 

 

 

 

 

 

 

 

 

SWITCH

 

 

 

 

 

 

 

 

 

 

 

 

INDICATOR

 

1

 

 

 

 

 

 

 

 

 

 

MAX

 

 

 

 

 

 

 

MIN

MAX 1

2 MIN

MAX

 

 

 

 

 

 

 

 

 

3

4

 

 

 

 

 

 

 

 

 

MIN

MAX

MIN

MAX

1/2

INCREASE

 

 

 

 

 

 

 

 

 

COMP EFF1

DIST

EQ EFF2

EFF3 DLY

REV

TOTAL

 

 

 

 

 

CONTROL

 

 

 

 

 

 

 

 

 

 

 

 

STORE

GROUP

EDIT

UTILITY

 

 

 

 

 

 

MIN

CONTROL

PEDAL

–

TYPE

+

 

 

 

SWITCH

 

(EXECUTE)

COMPARE

EXIT

PAGE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

BLINK

 

 

 

 

 

 

 

 

PRESENCE

OUTPUT

(DLY:TAP)

 

 

ADVANCED GUITAR EFFECTS PROCESSOR

 

 

 

 

 

 

 

 

3

 

 

 

 

 

 

 

 

 

 

 

DECREASE

 

 

 

 

 

 

 

 

 

 

 

–(TAP/HOLD)

 

 

 

 

 

 

 

 

 

USER

 

 

CONTROL

 

BANK

 

 

 

 

FUNCTION

 

 

 

 

 

 

 

 

 

 

PEDAL

 

 

 

 

 

 

 

 

 

 

 

4

 

 

 

 

 

 

 

 

 

 

 

 

Data entry knobs 1-4

MIN MAX

UTILITY/PAGE key

UTILITY

PAGE

STORE

(EXECUTE)

STORE/EXECUTE key

USER FUNCTION switch

USER

FUNCTION

Operation Advanced

1 In Play mode, press

the UTILITY/PAGE key three

times to call up the page shown below.

2 Use Data entry knob 2 to

set the "USER FUNCTION=" item to "PRESET".
This is the page for selecting the function of the USER FUNCTION switch.
USER FUNCTION=MANUAL 3

USER FUNCTION=PRESET 3

3 Press the

The Utility mode settings are stored

 

STORE/EXECUTE key two

and the unit returns to the Play

times.

mode.

4

5

Press the

USER FUNCTION switch while

playing the instrument in Play mode.

Select a patch from the new PRESET group.

The new PRESET group (folder) will be briefly shown on the display, such as "Pfold=B", and the group is switched.

The new patch becomes active. ("Selecting a patch" p. 11).

A01 8080LEAD LVL= 80

AMP ÁVOL ªOFF §HLD

USER

FUNCTION

Press

USER FUNCTION switch

A01 8080LEAD Pfold=B

AMP ÁVOL ªOFF §HLD

B01 8080LEAD LVL= 80

AMP ÁVOL ªOFF §HLD

B05 8080LEAD LVL= 80 AMP ÁVOL ªOFF §HLD

✎If Utility mode settings are not stored, they will remain active only until the unit is next turned off. When turned on again, NOthe unit reverts to the previous settings. If you wish to keep changes you have made, do not forget to press the

STORE/EXECUTE key twice to perform the store process. Note that any edited patch will also be stored at this time.

✎NOSimply pressing the USER FUNCTION switch does not yet change the currently selected patch.

■40