Upx | ZyXEL Communications U-336R/RE instruction

Command	Options		Function & Description	Ref.
	I12		Display physical layer status.
Ln	n=0-7		Speaker volume control. The higher	S24.4-6
	4 *		the value, the higher the volume.
Mn			Speaker control.	S21.1-2
	M0		Speaker always OFF.
	M1	*	Speaker ON until call is answered.
	M2		Speaker always ON.
	M3		Speaker ON after the last digit is
			dialed out and OFF when carrier is
			detected.
Nn	n=0-7		Ring volume control.'N0' will	S24.0-2
	5 *		disable the audio ring function.
O			Return to on-line state.
O1			Force modem to request a retrain.
Qn			Result code displayed.	S23.7
	Q0	*	Modem returns result code.
	Q1		Modem does not return result code.
	Q2		Modem returns result code but quiet	S40.1
			after answering on a RING (see also
			S42.2).
Sr.b=n			Set bit 'b' of S-register 'r' to value 'n'.
			'n' is a binary digit '0' or '1'.
Sr.b?			Display value of bit 'b' of S-register
			'r'.
Sr=n			Set S-register 'r' to value 'n'. 'n' must
			be a decimal number between 0 and
			255.
Sr?			Display value stored in S-register 'r'.
T			Ton dial.	S23.1
UPX			Download firmware to the Flash
			EPROM by using Xmodem
			protocol.

AT Command Set Summaries 79

Image 91

ZyXEL Communications U-336R/RE manual Upx

Contents

ZyXEL ZyXEL Limited Warranty Iii FCC Part 15 InformationCopyright 1997 by ZyXEL Acknowledgments Information for Canadian Users Page ∙ E-mail Contacting ZyXEL Vii Contents Leased Line Operation Synchronous Mode Operation Fax Operation Special Functions Upgrading Your Modem AT Command Set SummariesDiagnostics & Troubleshooting Status Registers & Result Codes Index Terminal PinoutsXii Standard Features Modem FeaturesIntroduction Intelligent Features Fax Compatibility Technical Specifications Enclosed Equipment Unpacking Your ModemRequired Equipment Becoming a Registered Owner Introduction Name Blinking InstallationInstallation 336R/RE Modem Card DSR TXDRXD DTR Required Steps for U-336R/RE Installation Connect to phone lines Installing the modem card Fax/Modem Communication Software Installation Hooking Up PowerConnect to Computers AT&F Setting Value For troubleshooting suggestions Installation Basic Modem Operation Understanding AT CommandsUsing the Windows 95 Hyper Terminal Program Basic Modem Operation ATEnter Dialing and Answering Techniques Dialing using the ATD Command ATS0=0 Making Your First ConnectionAuto-Answer and Hook Controls ATS0=n Quick Tips when issuing AT Commands AT Command Set/Type Example Command Description Modem Result Codes Changing S Register Values Viewing S Register Values AT&Zs=n Non-Volatile MemoryStoring Phone Numbers Dialing Stored Phone Numbers Helpful Hints for PC Computers Saving Settings and User Profiles AT Command Description Default Modem Settings for PC’sZyXEL Serial/Parallel I/O Card Mac Software Tips Special AT Command Settings for MacintoshHelpful Hints for Macintosh Computers Macintosh Serial Port Helpful Hints for UNIX-Based Computers Basic Modem Settings for UnixSerial Cable Unix Software Tips 25bis Command Set Synchronous Mode OperationSynchronous Mode Operation Clock Options Syntax Command with Description Parameters RTS Options Data Command State OptionsDialing from Synchronous Mode Sync AT&M1 Auto-Answer Answering from Synchronous ModeManual Answer Synchronous Mode Operation Leased Line Operation Connecting to a Leased LineLine Type Setting AT-Command Description Auto Handshake Power Level SettingLeased Line Handshaking Manual Connect AT*M1 Leased-Line Dial BackupDial Backup AT*M0 Aborting from Leased-Line Operation Terminating a Leased Line Connection Special Functions Special FunctionsSecurity Functions Levels of Security User Passwords Enters the callback number Command Function AT*Rab Remote ConfigurationAT*Wab Caller Number Delivery Caller ID Ring Here is an example Distinctive Ring Type Bit Ring Sequence Extended Distinctive Ring EDR Special Functions S51 Bit-mapped register default Bits Bin Dec Description Setting Up EDR CID/EDR RD EDR Application Example Special Functions Special Functions Modem as Fax Machine Fax OperationFax Operation Defining the Fax Command Sets Fax Command setsITU-T T.30 Fax Protocol Command Value Description Class 1 Command Set +FTH and +FRH support value 3 V.21 ch / 300 bps only Class 2 Command Set Value Command Syntax Description+FCIG=string Ln,df,ec,bf,st +FDCC=vr,br,wd +FDR +FDCS=vr,br,wd+FDIS=vr,br,wd,l Df,ec,bf,st +FMFR? +FK+FLID=string +FMDL? Response Value Function and Description +FREV?+FCFR +FVOICE +FPOLL +FCO Class 2.0 Command Set+FBS? +FCC=vr,br,w +FDT +FLI=string +FIS=vr,br,wdTpr,idr,nsr +FRQ=pgl,cbl +FNS=string+FPI=string DCE +FCICSI ID HEX +FNF A0-BF+FNC NSC FIF CIG ID +FNSNSS FIF +FPI Extended Fax AT Command Set Modem will wait for DC2 at the beginning of every Busy #PstringNo Dial Tone No Carrier Snnnn Field DescriptionPstring Flow Control Fax Reception from a BBS String Error LevelConnect Init AT&FX7S0=1#B1+FCLASS=6 ExtrnMail ZyXEL errorlevel AT Command Set Summaries AT Command Set SummariesBasic AT Command Set Command Options Function & Description Command Options Function & Description UPX Link Status Report output appears as follows Description of ATI2 Output Output Parameter Output Value Description Data Type Description DTE DTE/DCE Extended AT& Command Set Command Options Function & Description Command Options Function & Description Command Options Function & Description Command Options Function & Description Command Options Function & Description Extended AT* Command Set Command Options Function & Description Command Options Function & Description Basic S-Registers ATSn=x Command Function & Description +RefStatus Registers & Result Codes Register Descriptions Extended S-Registers ATSn=x Command Bit Dec Hex Function and description Command Bit Dec Hex Function and description Command Bit Dec Hex Function and description Command Bit Dec Hex Function and description Command Bit Dec Hex Function and description ATX1 ATX2 ATX3 ATX4 Command Bit Dec Hex Function and description Command Bit Dec Hex Function and description Command Bit Dec Hex Function and description Command Bit Dec Hex Function and description ATA Command Bit Dec Hex Function and description Command Bit Dec Hex Function and description Command Bit Dec Hex Function and description Command Bit Dec Hex Function and description Command Bit Dec Hex Function and description Command Bit Dec Hex Function and description Register bit number, b, used in ATSr.b=n ATSr.b=? ATXn Result Code Option Table Result Code Options+nnn Supported Numerical Verbose Connect Strings for Error Corrected ConnectionsResult Code Field Descriptions Field Name Possible Values 24000 Status Registers & Result Codes Diagnostics Diagnostics & TroubleshootingDiagnostics & Troubleshooting Power-On Self Test FR Calibration Loopback Tests Indicator Lights Line Condition Status Display Received Signal Power Level RX Link Status Report ATI2 Characters sent from the DTE to the modem for transmission Data bytes sent to the remote modem ∙ Local Hang-up ∙ Remote Hang-up ∙ Carrier Lost ∙ On Line AT Command Set Problems Trouble Shooting Your modem fails to execute AT commands Answer Problems Command Echo Problems Dialing Problems Connect Problems Data Transfer Problems Upgrading Your Modem Upgrading Your ModemUpgrading by Flash Eprom Type ATUPXenter Kernel Recovery Mode Terminal Pinouts Terminal PinoutsTerminal Blocks TIP Name Pin/Signal Direction DescriptionPC Serial Port Pinouts Signa Mac Modem Description Din Macintosh Serial Port Pinouts Terminal Pinouts Index Index Smartdrv