Makita DCS34 manual Putting Into Operation, Mounting the guide bar and saw chain

Page 18

PUTTING INTO OPERATION

CAUTION:

Before doing any work on the guide bar or chain, always

STOPswitch off the engine and pull the plug cap off the spark plug (see "Replacing the spark plug"). Always wear protective gloves!

CAUTION:

Start the chain saw only after having assembled it completely and inspected!

	Mounting the guide bar and saw chain
	Use the universal wrench delivered with the chain saw for
	the following work.
1	Put the chain saw on a stable surface and carry out the
	following steps for mounting the guide bar and chain:

5 4

7 6

Release the chain brake by pulling the hand guard (1) in direction of arrow.

Unscrew retaining nuts (2).

Pull off the sprocket guard (3).

Turn the chain adjusting screw (4) to the left (counterclock- wise) until the pin (5) is at the left stop.

Position the guide bar (6). Make sure that the pin (7) of the chain tightener is in the hole on the guide bar.

Image 18

Contents DCS Contents Makita DCSSymbols Delivery inventorySafety precautions for chain saw operators Additional safety precautionsAnsi B175.1-1991 General Safety PrecautionsDiscription of symbols used on chain saws OperatorUse of the saw Proper clothingSaw Transporting the chain sawFueling Chain saw operating instructionsFeet Fueling instructionsImportant adjustments Working conditionsCutting instructions Kickback Reactive forces during the cut, including kickbackSpeed of contact at which the cutter contacts the object Saw chain cutter sharpnessTo avoid kickback Depth gaugesTo avoid pushback Cutting techniquesPushback To avoid pull-inFelling instructions = cutting down areaPlunge-Cut Method Sectioning MethodLimbing Bucking129 Maintenance and Repair Maintaining and storing the sawDenomination of components 13 14 Identification plate DCSFuel tank cap Technical data DCS Approved bar and chain combinationsLength Putting Into Operation Mounting the guide bar and saw chainTightening the saw chain Checking the chain tension Chain brakeEngaging the chain brake braking Releasing the chain brakeFuel mixture FuelChain oil Correct mixture ratioRefuelling Clean screw cap and tank after refuellingWaste oil Important note on bio-degradable chain oilsChecking the chain lubrication Warm start Starting the engineCold start Stopping the engineChecking the safety chain brake Adjusting the carburetorSet idle speed Sharpening the saw chain Stop 025Min Files and how to work with them Multi-purpose grease Cleaning the brake band and sprocket interiorCleaning the guide bar, lubricating the sprocket nose Grease gunCleaning the air filter Stop Replacing the saw chainReplacing the suction head Checking the ignition spark Replacing / cleaning the spark arrester screenReplacing the spark plug Stop 020Instructions for daily and periodic maintenance Service, spare parts and guaranteeMaintenance and repair Spare parts TroubleshootingGuarantee Malfunction System Observation CauseExtract from the spare parts list DCSSommaire Symboles Etendue de la fournitureMesures de sé curité supplé mentaires Arrêtez le moteur avant de poser la tronçonneuse’utilisateur Description des symboles figurant sur les tronç onneusesMesures gé né rales de sé curité Condition physiqueUtilisation de la tronç onneuse Quels vê tements porter?La tronç onneuse Transport de la tronç onneuseInstructions de ravitaillement PiedsRavitaillement en carburant Dé marrageRé glages importants Conditions de travailInstructions de coupe Choc de recul Kickback Affû tage des plaquettes de coupe de la chaîne Pour é viter le choc de reculLes limiteurs de profondeurs Pour é viter le recul Techniques de coupeLe recul Pour é viter la tractionInstructions d’abattage = zone d’abattageMé thode de sectionnement Mé thode de coupe en plongé eEbranchage Dé bitageEntretien et ré paration Entretien et stockage de la tronç onneuseAnnée de construction Dé signation des piè ces 13 14 Plaque signatiqueDCS Numéro de sérieGuide 3/8 Caracté ristiques techniques DCSCombinaisons autorisé es de guides et de chaînes Longueur Ré fé renceMise EN Route Montage du guide et de la chaîne de sciageTendre la chaîne de sciage Dé clencher le frein de chaîne bloquer Frein de chaîneContrô le de la tension de la chaîne Libé rer le frein à mainMé lange carburant CarburantsHuile de chaîne de sciage Stockage du carburantHuile Usagé e Remplissage des ré servoirsVé rifier le graissage de la chaîne RemarqueDé marrage à chaud Dé marrer le moteurDé marrage à froid Arrê ter le moteurVé rifier le frein de chaîne 65 mm Affû tage de la chaîneDe sciage 65 mmLime et guidage de la lime Pompe à graisse Remplacement de la cré pine d’aspiration Nouvelle chaîne de sciageNettoyage du filtre à air Stop Remplacement de bougie Stop Changement / nettoyage du pare-é tincellesVé rification de l’é tincelle d’allumage Service d’atelier, piè ces de rechange et garantie Indications de maintenance et d’entretien pé riodiquesMaintenance et ré parations Garantie Recherche de pannesPiè ces de rechange Panne Systè me Observation OrigineExtrait de la liste des piè ces de rechange Makita U.S.A., Inc Makita Canada Inc USA