Makita DCS34 manual Files and how to work with them

Page 27

Files and how to work with them

Sharpen using a special file holder with a saw chain round file dia. 5/32" (4.0 mm). Normal round files are not appropriate for this work. See "Accessories" for the order number.

The file should cut only when pushed forwards (arrow). Lift the file when leading it backwards.

First sharpen the shortest cutter. The length of this cutter is then the standerd for all other cutters of the chain.

Always guide the file horizontally (90o to the guide bar).

D

The file holder makes file guidance easier. It is marked for

the correct 30° sharpening angle (keep the marks parallel with

4/5

the chain when filing, see illustration) and limits the cut depth

to the correct 4/5 of the file diameter. See "Accessories" for

the order number.

30°

E

After having sharpened the chain, the height of the depth limiter must be checked by means of a chain gauge. See "Accessories" for the order number.

Correct even the smallest excess height (13) with a special flat file. See "Accessories" for the order number.

Round off the front of the depth limiter (14).

13

14

F

27

Image 27

Contents DCS Makita DCS ContentsDelivery inventory SymbolsAdditional safety precautions Safety precautions for chain saw operatorsOperator General Safety PrecautionsDiscription of symbols used on chain saws Ansi B175.1-1991Transporting the chain saw Proper clothingSaw Use of the sawFueling instructions Chain saw operating instructionsFeet FuelingImportant adjustments Working conditionsCutting instructions Reactive forces during the cut, including kickback KickbackDepth gauges Saw chain cutter sharpnessTo avoid kickback Speed of contact at which the cutter contacts the objectTo avoid pull-in Cutting techniquesPushback To avoid pushback= cutting down area Felling instructionsSectioning Method Plunge-Cut MethodLimbing Bucking129 Maintaining and storing the saw Maintenance and RepairDenomination of components 13 14 Identification plate DCSFuel tank cap Technical data DCS Approved bar and chain combinationsLength Mounting the guide bar and saw chain Putting Into OperationTightening the saw chain Releasing the chain brake Chain brakeEngaging the chain brake braking Checking the chain tensionCorrect mixture ratio FuelChain oil Fuel mixtureImportant note on bio-degradable chain oils Clean screw cap and tank after refuellingWaste oil RefuellingChecking the chain lubrication Stopping the engine Starting the engineCold start Warm startChecking the safety chain brake Adjusting the carburetorSet idle speed Sharpening the saw chain Stop 025Min Files and how to work with them Grease gun Cleaning the brake band and sprocket interiorCleaning the guide bar, lubricating the sprocket nose Multi-purpose greaseCleaning the air filter Stop Replacing the saw chainReplacing the suction head 020 Replacing / cleaning the spark arrester screenReplacing the spark plug Stop Checking the ignition sparkInstructions for daily and periodic maintenance Service, spare parts and guaranteeMaintenance and repair Malfunction System Observation Cause TroubleshootingGuarantee Spare partsDCS Extract from the spare parts listSommaire Etendue de la fourniture SymbolesArrêtez le moteur avant de poser la tronçonneuse Mesures de sé curité supplé mentairesCondition physique Description des symboles figurant sur les tronç onneusesMesures gé né rales de sé curité ’utilisateurTransport de la tronç onneuse Quels vê tements porter?La tronç onneuse Utilisation de la tronç onneuseDé marrage PiedsRavitaillement en carburant Instructions de ravitaillementRé glages importants Conditions de travailInstructions de coupe Choc de recul Kickback Affû tage des plaquettes de coupe de la chaîne Pour é viter le choc de reculLes limiteurs de profondeurs Pour é viter la traction Techniques de coupeLe recul Pour é viter le recul= zone d’abattage Instructions d’abattageMé thode de coupe en plongé e Mé thode de sectionnementDé bitage EbranchageEntretien et stockage de la tronç onneuse Entretien et ré parationNuméro de série Dé signation des piè ces 13 14 Plaque signatiqueDCS Année de constructionLongueur Ré fé rence Caracté ristiques techniques DCSCombinaisons autorisé es de guides et de chaînes Guide 3/8Montage du guide et de la chaîne de sciage Mise EN RouteTendre la chaîne de sciage Libé rer le frein à main Frein de chaîneContrô le de la tension de la chaîne Dé clencher le frein de chaîne bloquerStockage du carburant CarburantsHuile de chaîne de sciage Mé lange carburantRemplissage des ré servoirs Huile Usagé eRemarque Vé rifier le graissage de la chaîneArrê ter le moteur Dé marrer le moteurDé marrage à froid Dé marrage à chaudVé rifier le frein de chaîne 65 mm Affû tage de la chaîneDe sciage 65 mmLime et guidage de la lime Pompe à graisse Remplacement de la cré pine d’aspiration Nouvelle chaîne de sciageNettoyage du filtre à air Stop Remplacement de bougie Stop Changement / nettoyage du pare-é tincellesVé rification de l’é tincelle d’allumage Service d’atelier, piè ces de rechange et garantie Indications de maintenance et d’entretien pé riodiquesMaintenance et ré parations Panne Systè me Observation Origine Recherche de pannesPiè ces de rechange GarantieExtrait de la liste des piè ces de rechange USA Makita U.S.A., Inc Makita Canada Inc