Homelite UT80432 manuel dutilisation Packing List, Tools Needed, Raising and Lowering the Handle

Page 12

ASSEMBLY

PACKING LIST

Pressure Washer

25 ft. High Pressure Hose Trigger Handle Holder Spray Wand Holder

Phillips Screw [1/4-20 x 2.27 in.] (2) Phillips Screw (1/4-20 x 1.85 in.) Nuts (3)

Trigger Handle

Spray Wand

5-in-1 Change Over Nozzle Injection Hose plus Filter Washer

4-Cycle Engine Lubricant (SAE 30 or SAE 10W30) High Pressure Hose Storage

Operator’s Manual

TOOLS NEEDED

See Figure 1a.

The following tools (not included or drawn to scale) are needed for assembly:

7/16 in. combination wrench Phillips screwdriver

WARNING:

If any parts are damaged or missing do not operate this product until the parts are replaced. Use of this product with damaged or missing parts could result in serious personal injury.

WARNING:

Do not attempt to modify this product or create acces- sories not recommended for use with this product. Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious personal injury.

WARNING:

To prevent accidental starting that could cause serious personal injury, always disconnect the engine spark plug wire from the spark plug when assembling parts.

RAISING AND LOWERING THE HANDLE

See Figure 2.

nTo raise the handle: pull the handle up until the handle release knob snaps through the locking hole to secure the handle in place.

nTo lower the handle: pull the handle release knob out then lower the handle to the position shown in figure 2.

INSTALLING TRIGGER HANDLE HOLDER, SPRAY WAND HOLDER AND HOSE STORAGE

See Figure 3 - 4.

nRaise handle as described in the Raising and Lowering Handle section.

nPlace hose storage onto the handle as shown.

nAlign the holes in the hose storage with the holes in the handle.

nInsert long screw (1/4-20 x 2.27 in.) through the holes in the left side of the handle and hose storage.

nPlace nut onto long screw and tighten.

nPlace the trigger handle holder onto the handle as shown.

nAlign the holes in the trigger handle holder with the holes in the hose storage and the handle.

nInsert second long screw through the holes in handle, hose storage, and trigger handle holder.

nSlide washer onto screw. Then, place nut onto screw and tighten.

nPlace spray wand holder onto pressure washer frame.

nAlign the holes in the spray wand holder with the holes in the pressure washer frame.

nInsert short screw (1/4-20 x 1.85 in.) through the holes in the spray wand holder and the pressure washer frame.

nPlace nut onto screw and tighten.

ASSEMBLING THE TRIGGER HANDLE

See Figure 5.

nPlace the threaded end of the spray wand in the connector on the end of the trigger handle.

nTurn the connector clockwise until it stops. This secures the spray wand in place.

CONNECTING HIGH PRESSURE HOSE TO TRIGGER HANDLE

See Figure 6.

nScrew the collar on the high pressure hose into the trigger handle inlet coupler by turning the hose collar clockwise.

nPull on the hose to be certain it is properly secured.

CONNECTING THE HIGH PRESSURE HOSE TO THE PUMP

See Figure 7.

After the high pressure hose has been uncoiled and attached to the spray wand:

nAlign the collar on the threaded nipple on the pump.

nInsert the nozzle on the end of the high pressure hose collar into the threaded nipple.

nTurn the collar clockwise to tighten the hose securely to the pump.

nPull on the hose to be certain it is properly secured.

Page 8 — English

Page 11 Page 13
Image 12
Page 11 Page 13
Contents PSI Pressure Washer Save this Manual for Future ReferenceSoap Soap Iii Paper clip pièces de papier, clips de papel Table of Contents IntroductionImportant Safety Instructions Read ALL Instructions3 English Specific Safety Rules 4 EnglishSymbols 5 English6 English Features AssemblyConnecting High Pressure Hose to Trigger Handle Connecting the High Pressure Hose to the PumpPacking List Tools NeededConnecting the Garden Hose to the Pressure Washer OperationAttaching Injection Hose See Figures 9Applications Adding Lubricant to the EngineStarting and Stopping the Pressure Washer Oxygenated FuelsUsing the Spray Wand Trigger INSTALLING/REMOVING NozzlesUsing the 5-IN-1 Change Over Nozzle Using the High Pressure HoseWashing with Detergent Rinsing with the Pressure WasherMoving the Pressure Washer See Figures 18Maintenance Pump Lubrication Storing the Pressure WasherPreparing for USE After Storage 14 EnglishPeriodic Maintenance Schedule Maintenance Items Each use Weekly 25 hrs 50 hrs 200 hrs15 English Troubleshooting Problem Cause Solution16 English Warranty Limited NON Engine Warranty Statement17 English Instructions Importantes Concernant LA Sécurité AVERTISSEMENT Lire Toutes LES Instructions  Faire preuve de prudence pour éviter de glisser ou tomberRègles DE Sécurité Particulières 4 FrançaisSymboles Avertissement5 Français 6 Français Caractéristiques AssemblageListe DE Contrôle Outils NécessairesRélever ET Abaisser LA Poignée Assemblage DE Poignée DE GâchetteInstallation DU Tuyau D’INJECTION UtilisationConnexion DU Tuyau D’ARROSAGE AU Nettoyeur Haute Pression AJOUT/VÉRIFICATION DE LubrifiantCarburants Oxygénés Appoint D’ESSENCEMise EN Marche / Arrêt DU Nettoyeur Haute Pression Voir les figures 13INSTALLATION/RETRAIT DES Buses Fonctionnement Poignée DE GâchetteUtilisation DE LA Buse À Permutation 5 EN Utilisation DU Tuyau Haute PressionDéplacement DU Nettoyeur Haute Pression Nettoyage Avec DU DétergentRinçage Avec LE Nettoyeur Haute Pression Voir les figures 18 etEntretien Entretien DE BuseEntretien Général Nettoyage DU Filtre À AIRRemise EN Service Après Remisage Changement Huile DE MoteurLubrification DU Pompe Remisage DU Nettoyeur Haute PressionTableau DE Calendrier D’ENTRETIEN Périodique 15 FrançaisProblème Cause Solution Dépannage16 Français Garantie Énoncé DE LA Garantie Limitée Hors Moteur17 Français Instrucciones DE Seguridad Importantes Guarde Estas Instrucciones Área DE TrabajoPágina 3 Español Reglas DE Seguridad Específicas Página 4 EspañolSímbolos PeligroAdvertencia PrecauciónPágina 6 Español Características ArmadoLista DE Empaquetado Herramientas NecesariasLevantar Y Bajar EL Mango Armado DE Mango DEL GatilloFuncionamiento Cómo Conectar LA Manguera DE InyeccionPágina 9 Español Usos Abastecimiento DE Lubricante DEL MotorCombustibles Oxigenados Abastecimiento DEL Tanque DE GasolinaUSO DEL Mango DEL Gatillo Instalar Y Desmontaje LAS BoquillasUSO DE LA Boquilla Intercambiable 5 EN USO DE LA Manguera DE Alta PresiónLavado CON Detergente Traslado DE LA Lavadora DE PresiónPágina 12 Español Mantenimiento Mantenimiento GeneralMantenimiento DE LAS Boquillas Limpieza DEL Filtro DE AireCambio DE Aceite DE Motor Lubricación DE LA BombaGuardado DE LA Lavadora DE Presión Página 14 EspañolPrograma DE Mantenimiento Página 15 EspañolSolución DE Problemas Problema Causa SoluciónPágina 16 Español Garantía Página 17 EspañolOPERATOR’S Manual Manuel D’UTILISATION Manual DEL Operador

UT80432 specifications

The Homelite UT80432 is a powerful and versatile electric chainsaw designed for homeowners and DIY enthusiasts who require a reliable tool for cutting and trimming tasks around the yard. As a part of the Homelite lineup, this chainsaw combines innovative technologies with user-friendly features, making it an ideal choice for both novice and experienced users.

One of the most notable features of the UT80432 is its robust 8-amp motor. This powerful engine provides ample cutting strength, allowing users to tackle various tasks such as pruning branches, cutting firewood, or handling small to medium-sized trees. The chainsaw's design focuses on efficiency, enabling users to make swift and precise cuts with minimal effort.

The UT80432 is equipped with a 12-inch cutting bar and chain, which strikes an excellent balance between maneuverability and cutting capacity. This length is suitable for a variety of applications, ensuring that users can perform their tasks effectively without being overwhelmed by the size and weight of the tool. Its lightweight construction further enhances usability, making it easy to carry and operate for extended periods.

Safety is a paramount concern in any power tool, and the Homelite UT80432 doesn't fall short in this aspect. It features a chain brake that immediately halts the chain's operation in the event of kickback, providing an additional layer of protection for users. Additionally, the chainsaw includes a safety switch to prevent accidental starts, ensuring peace of mind during operation.

Another key characteristic of the UT80432 is its tool-free chain tensioning system. This feature simplifies the process of adjusting the chain tension, making it easier for users to maintain optimal performance without the need for specialized tools. The clear viewing window for the oil reservoir allows users to easily monitor oil levels, which helps prolong the life of the chain and bar.

The chainsaw is further designed with ergonomic considerations. Its cushioned handle ensures a comfortable grip, reducing user fatigue during prolonged use. The overall weight distribution of the unit contributes to better control and stability, which fosters greater precision during cutting tasks.

In summary, the Homelite UT80432 is an efficient and user-friendly electric chainsaw that stands out due to its powerful motor, lightweight design, safety features, and easy maintenance capabilities. It is a practical addition to any homeowner's toolkit, particularly for those looking to manage their outdoor spaces effectively and safely.
Top Page Image Contents